• I.S. EN 161:2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-12-2021

    Language(s):  English

    Published date:  11-04-2011

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Classification
    5 Units of measurement and test conditions
    6 Construction requirements
    7 Performance
    8 EMC/Electrical requirements
    9 Marking, installation and operating instructions
    Annex A (informative) - Gas connections in common use
            in the various countries
    Annex B (informative) - Leak-tightness test - volumetric
            method
    Annex C (informative) - Leak-tightness test - pressure
            loss method
    Annex D (normative) - Conversion of pressure loss into
            leakage rate
    Annex E (normative) - Electrical/electronic component fault
            modes
    Annex F (normative) - Additional requirements for safety
            accessories and pressure accessories as defined in
            EU Directive 97/23/EC
    Annex G (normative) - Materials for pressurized parts
    Annex H (informative) - Additional materials for pressurized
            parts
    Annex I (normative) - Requirements for controls used in
            DC supplied gas burners and gas burning appliances
    Annex AA (normative) - Method for the determination of
             Performance Level (PL)
    Annex BB (informative) - Model of a FMEA for valves
    Annex ZA (informative) - Relationship between this European
             Standard and the Essential Requirements of EU
             Directive 2009/142/EC relating to appliances burning
             gaseous fuels
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the safety, construction and performance requirements for automatic shutoff valves for use with gas burners, gas appliances and similar use, hereafter referred to as 'valves'.

    General Product Information - (Show below) - (Hide below)

    Development Note 2011 Edition Re-Issued in February 2013 & incorporates AMD 3 2013. (02/2013)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 13906-1:2013 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs
    EN 175301-803:2006 Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable
    EN 13906-2:2013 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs
    EN 14459:2015 Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 61058-1:2016 Switches for appliances - Part 1: General requirements
    EN 13611:2015/AC:2016 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
    EN 61058-1:2002/A2:2008 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    EN 60730-1:2016 Automatic electrical controls - Part 1: General requirements
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective