I.S. EN 26:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
Hardcopy , PDF
11-01-2024
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification of water heaters
5 Constructional requirements
6 Operational requirements
7 Rational use of energy
8 Fitness for purpose
9 Marking and instructions
10 Ecodesign Data
11 Energy Labelling Data
Annex A (informative) - National situations
Annex B (normative) - Test apparatus for type C[1], C[3], B[4]
and B[5] water heaters
Annex C (normative) - Test apparatus for type C[21] appliances
Annex D (normative) - Description of the sealed room for the
tests of type A[AS] appliances
Annex E (informative) - Soundness of the gas circuit test -
Volumetric method
Annex F (informative) - Principal symbols and abbreviations used
Annex G (informative) - Guidelines for extension to other categories
Annex H (informative) - A deviations
Annex I (normative) - Lists of materials currently used
Annex J (normative) - Test methods to determine the effects of
to long-term thermal load, long-term condensate exposure,
condensing/non-condensing cycling and resistance to UV
radiation
Annex K (informative) - NOx conversion calculation
Annex L (normative) - Parts in copper or copper alloys
Annex M (informative) - Compilation of the test conditions for
the various gas families
Annex N (informative) - Alternative Method for the determination
of the nominal heat input or the maximum and minimum heat
input (according to 6.3.1) for appliances using a pneumatic
gas/air ratio control system
Annex ZA (informative) - Relationship between this European
Standard and the requirements of EU Directive 2009/142/EC
Annex ZB (informative) - Relationship between this European
Standard and the requirements of Commission Regulation
(EU) No 814/2013
Annex ZC (informative) - Relationship between this European
Standard and the requirements of Commission Delegated
Regulation (EU) No 812/2013
Bibliography
Specifies the specifications and test methods concerning the construction, safety, rational use of energy and fitness for purpose, and also the classification and marking of gas-fired instantaneous water heaters for sanitary uses, hereafter called 'water heaters'.
DocumentType |
Standard
|
Pages |
172
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NEN EN 26 : 2015 | Identical |
DIN EN 26:2015-08 | Identical |
NBN EN 26 : 2015 | Identical |
UNI EN 26 : 2007 | Identical |
EN 26:2015 | Identical |
UNE-EN 26:2016 | Identical |
SN EN 26:2015 | Identical |
BS EN 26:1998 | Identical |
NF EN 26 : 2015 | Identical |
NS EN 26 : 1997 | Identical |
EN 1859:2009+A1:2013 | Chimneys - Metal chimneys - Test methods |
IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV | Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
EN 15502-1:2012+A1:2015 | Gas-fired heating boilers - Part 1: General requirements and tests |
IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
EN 1856-2:2009 | Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes |
EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
EN 13203-1:2015 | Gas fired domestic appliances producing hot water - Part 1: Assessment of performance of hot water deliveries |
EN 13216-1:2004 | Chimneys - Test methods for system chimneys - Part 1: General test methods |
ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
EN ISO 3166-1:2014 | Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013) |
EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
EN 14241-1:2013 | Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners |
ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
EN 14459:2015 | Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment |
EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
EN 125:2010+A1:2015 | Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
EN 126:2012 | Multifunctional controls for gas burning appliances |
CEN/TR 1749:2014 | European scheme for the classification of gas appliances according to the method of evacuation of the combustion products (types) |
EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
EN 60335-2-102:2016 | Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
ISO 6914:2013 | Rubber, vulcanized or thermoplastic Determination of ageing characteristics by measurement of stress relaxation in tension |
EN 14471:2013+A1:2015 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
CR 1472:1997 | General guidance for the marking of gas appliances |
ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
ISO 3166-1:2013 | Codes for the representation of names of countries and their subdivisions Part 1: Country codes |
EN 1443:2003 | Chimneys - General requirements |
EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
EN 1856-1:2009 | Chimneys - Requirements for metal chimneys - Part 1: System chimney products |
EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
ISO 301:2006 | Zinc alloy ingots intended for castings |
EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
ISO 178:2010 | Plastics Determination of flexural properties |
ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
EN 513:1999 | Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering |
EN 88-1:2011+A1:2016 | Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa |
ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
EN 573-1:2004 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 1: Numerical designation system |
EN 15036-1:2006 | Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1: Airborne noise emissions from heat generators |
ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
ISO 2781:2008 | Rubber, vulcanized or thermoplastic Determination of density |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.