I.S. EN 573-3:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ALUMINIUM AND ALUMINIUM ALLOYS - CHEMICAL COMPOSITION AND FORM OF WROUGHT PRODUCTS - PART 3: CHEMICAL COMPOSITION AND FORM OF PRODUCTS
Hardcopy , PDF
English
01-01-2013
14-09-2019
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
1 Scope
2 Normative references
3 Chemical composition limits
4 Writing rules
5 Alloy designations
6 Sequence of elements
7 Rounding rules for determination of compliance
Annex A (normative) - Form of products
Annex B (normative) - Guidelines for the introduction
of new wrought aluminium and wrought aluminium
alloys in CEN/TC 132 standards
Bibliography
Describes the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
| DevelopmentNote |
Supersedes I.S. EN 573-4. (09/2007)
|
| DocumentType |
Standard
|
| Pages |
39
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 573-3 : 2013 | Identical |
| EN 573-3:2013 | Identical |
| NF EN 573-3 : 2013 | Identical |
| BS EN 573-3:2013 | Identical |
| DIN EN 573-3:2013-12 | Identical |
| NS EN 573-3 : 2013 | Identical |
| NEN EN 573-3 : 2013 | Identical |
| ONORM EN 573-3 : 2013 | Identical |
| UNE-EN 573-3:2014 | Identical |
| S.R. 325:2013+A2:2018/AC:2019 | RECOMMENDATIONS FOR THE DESIGN OF MASONRY STRUCTURES IN IRELAND TO EUROCODE 6 |
| I.C.P. 2:2002 | SLATING AND TILING |
| EN 1715-2:2008 | Aluminium and aluminium alloys - Drawing stock - Part 2: Specific requirements for electrical applications |
| EN 13957:2008 | Aluminium and aluminium alloys - Extruded round, coiled tube for general applications - Specification |
| EN 1301-2:2008 | Aluminium and aluminium alloys - Drawn wire - Part 2: Mechanical properties |
| EN 851:2014 | Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications |
| EN 683-2:2006 | Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties |
| EN 573-2:1994 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 2: Chemical symbol based designation system |
| EN 485-2:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties |
| EN 13981-2:2004 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 2: Plates and sheets |
| TEAL 1 : 2015 | INTERNATIONAL ALLOY DESIGNATIONS AND CHEMICAL COMPOSITION LIMITS FOR WROUGHT ALUMINUM AND WROUGHT ALUMINUM ALLOYS |
| EN 586-2:1994 | Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements |
| EN 1396:2015 | Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications |
| EN 570:2007 | Aluminium and aluminium alloys - Impact extrusion slugs obtained from wrought products - Specification |
| EN 541:2006 | Aluminium and aluminium alloys - Rolled products for cans, closures and lids - Specifications |
| EN 13958:2008 | Aluminium and aluminium alloys - Cold drawn, round, coiled tube for general applications - Specification |
| EN 13981-1:2003 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 1: Extruded products |
| EN 14286:2008 | Aluminium and aluminium alloys - Weldable rolled products for tanks for the storage and transportation of dangerous goods |
| EN 14121:2009 | Aluminium and aluminium alloys - Sheet, strip and plate for electrotechnical applications |
| EN 941:2014 | Aluminium and aluminium alloys - Circle and circle stock for the production of general applications - Specifications |
| EN 12392:2016 | Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment |
| EN 13981-4:2006 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 4: Forgings |
| EN 754-2:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties |
| EN 1386:2007 | Aluminium and aluminium alloys - Tread plate - Specifications |
| EN 1592-2:1997 | Aluminium and aluminium alloys - HF seam welded tubes - Part 2: Mechanical properties |
| EN 1715-4:2008 | Aluminium and aluminium alloys - Drawing stock - Part 4: Specific requirements for welding applications |
| EN 546-2:2006 | Aluminium and aluminium alloys - Foil - Part 2: Mechanical properties |
| EN 573-1:2004 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 1: Numerical designation system |
| EN 755-2:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties |
| EN 1715-3:2008 | Aluminium and aluminium alloys - Drawing stock - Part 3: Specific requirements for mechanical uses (excluding welding) |
| EN 603-2:1996 | Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.