I.S. EN 60079-19:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
EXPLOSIVE ATMOSPHERES - PART 19: EQUIPMENT REPAIR, OVERHAUL AND RECLAMATION
Hardcopy , PDF
09-01-2020
English
01-01-2011
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Additional requirements for the repair and overhaul of equipment
with type of protection 'd' (flameproof)
6 Additional requirements for the repair and overhaul of equipment
with type of protection 'i' (intrinsic safety)
7 Additional requirements for the repair and overhaul of equipment
with type of protection 'p' (pressurized)
8 Additional requirements for the repair and overhaul of equipment
with type of protection 'e' (increased safety)
9 Additional requirements for the repair and overhaul of equipment
with type of protection 'n'
10 Additional requirements for the repair and overhaul of equipment
covered by IEC 60079-26
11 Additional requirements for the repair and overhaul of equipment
with type of protection Group III 't' (formerly know as 'tD'
or DIP)
12 Additional requirements for the repair and overhaul of equipment
with type of protection pressurization 'pD'
Annex A (normative) - Identification of repaired equipment by
marking
Annex B (normative) - Knowledge, skills and competencies of
'Responsible Persons' and 'Operatives'
Annex C (normative) - Requirements for measurements in flameproof
equipment during overhaul, repair and reclamation
(including guidance on tolerances)
Annex ZA (normative) - Normative references to international
publications with their corresponding European publications
Bibliography
Provides instructions, principally of a technical nature, on the repair, overhaul, reclamation and modification of equipment designed for use in explosive atmospheres.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
166
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 60079-19 : 2015-09 | Identical |
| NBN EN 60079-19 : 2011 AMD 1 2015 | Identical |
| NF EN 60079-19 : 2011 AMD 1 2015 | Identical |
| EN 60079-19:2011/A1:2015 | Identical |
| IEC 60079-19:2010+AMD1:2015 CSV | Identical |
| BS EN 60079-19 : 2011 | Identical |
| ISO/IEC 17000:2004 | Conformity assessment Vocabulary and general principles |
| ISO 4526:2004 | Metallic coatings Electroplated coatings of nickel for engineering purposes |
| EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
| IEC 60050-426:2008 | International Electrotechnical Vocabulary (IEV) - Part 426: Equipment for explosive atmospheres |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 6158:2011 | Metallic and other inorganic coatings Electrodeposited coatings of chromium for engineering purposes |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN ISO 6158:2011 | Metallic and other inorganic coatings - Electrodeposited coatings of chromium for engineering purposes (ISO 6158:2011) |
| EN ISO 4526:2004 | Metallic coatings - Electroplated coatings of nickel for engineering purposes (ISO 4526:2004) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.