Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 60143-1:2015

    Current The latest, up-to-date edition.

    SERIES CAPACITORS FOR POWER SYSTEMS - PART 1: GENERAL

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2015

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    FOREWORD
    1 Scope and object
    2 Normative references
    3 Terms and definitions
    4 Service conditions
    5 Quality requirements and tests
    6 Insulation level
    7 Overloads, overvoltages and duty cycles
    8 Safety requirements
    9 Markings and instruction books
    10 Guide for selection of ratings, installation and operation
    Annex A (normative) - Test requirements and application
            guide for external fuses and units to be externally fused
    Annex B (informative) - Economic evaluation of series
            capacitor bank losses
    Annex C (informative) - Capacitor bank fusing and unit
            arrangement
    Annex D (informative) - Examples of typical connection
            diagrams for large series capacitor installations for
            transmission lines
    Annex E (informative) - Precautions to be taken to avoid
            pollution of the environment by polychlorinated
            biphenyls
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Pertains both to capacitor units and capacitor banks intended to be used connected in series with an a.c. transmission or distribution line or circuit forming part of an a.c. power system having a frequency of 15 Hz to 60 Hz.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60060-2:2010 High-voltage test techniques - Part 2: Measuring systems
    IEC 60143-2:2012 Series capacitors for power systems - Part 2: Protective equipment for series capacitor banks
    IEC 60270:2000+AMD1:2015 CSV High-voltage test techniques - Partial discharge measurements
    IEC 61048:2006+AMD1:2015 CSV Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp circuits - General and safety requirements
    EN 62271-1:2017 High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
    IEC 60050-601:1985 International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General
    IEC TS 60815-2:2008 Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems
    EN 60143-3:2015 Series capacitors for power systems - Part 3: Internal fuses
    EN 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
    EN 60549:2013 High-voltage fuses for the external protection of shunt capacitors
    IEC 60909-0:2016 Short-circuit currents in three-phase a.c. systems - Part 0: Calculation of currents
    IEC 60549:2013 High-voltage fuses for the external protection of shunt capacitors
    IEC TR 60996:1989 Method for verifying accuracy of tan delta measurements applicable to capacitors
    IEC 61049:1991 Capacitors for use in tubular fluorescent and other discharge lamp circuits. Performance requirements
    EN 60143-2:2013 Series capacitors for power systems - Part 2: Protective equipment for series capacitor banks
    IEC 60721-2-6:1990 Classification of environmental conditions. Part 2: Environmental conditions appearing in nature. Earthquake vibration and shock
    IEC 60871-1:2014 Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V - Part 1: General
    IEC 60273:1990 Characteristic of indoor and outdoor post insulators for systems with nominal voltages greater than 1000 V
    EN 60071-1:2006/A1:2010 INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES
    IEC 62271-1:2017 High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
    IEC 60252-1:2010+AMD1:2013 CSV AC motor capacitors - Part 1: General - Performance, testing andrating - Safety requirements - Guidance for installation and operation
    IEC 60071-2:1996 Insulation co-ordination - Part 2: Application guide
    IEC 60050-436:1990 International Electrotechnical Vocabulary (IEV) - Part 436: Power capacitors
    EN 60071-2:1997 Insulation co-ordination - Part 2: Application guide
    IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
    IEC 60071-1:2006+AMD1:2010 CSV Insulation co-ordination - Part 1: Definitions, principles and rules
    EN 60871-1:2014 Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V - Part 1: General
    IEC 60143-3:2015 Series capacitors for power systems - Part 3: Internal fuses
    IEC TS 60815-1:2008 Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles
    IEC 60143-4:2010 Series capacitors for power systems - Part 4: Thyristor controlled series capacitors
    EN 60143-4 : 2010 SERIES CAPACITORS FOR POWER SYSTEMS - PART 4: THYRISTOR CONTROLLED SERIES CAPACITORS
    IEEE 693-2005 IEEE Recommended Practice for Seismic Design of Substations
    IEC TS 60815-3:2008 Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems
    IEC 60110-1:1998 Power capacitors for induction heating installations - Part 1: General
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective