• I.S. EN 60297-3-106:2010

    Current The latest, up-to-date edition.

    MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-106: ADAPTATION DIMENSIONS FOR SUBRACKS AND CHASSIS APPLICABLE WITH METRIC CABINETS OR RACKS IN ACCORDANCE WITH IEC 60917-2-1

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope and object
    2 Normative references
    3 Arrangement overview and definitions
    4 Dimensions for flanges of 19 in subracks or chassis
      applicable for mounting on metric cabinets or racks
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Describes dimensions for mounting flanges of 19 in subracks or chassis that are to be mounted into metric cabinets or racks.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60297-3-101:2004 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units
    IEC 61587-2:2011 Mechanical structures for electronic equipment - Tests for IEC 60917 and 60297 - Part 2: Seismic tests for cabinets and racks
    IEC 60917-2-1:1993 Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 1: Detail specification - Dimensions for cabinets and racks
    IEC 61587-3:2013 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets and subracks
    IEC 61587-1:2016 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
    EN 60297-3-101:2004 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-101: SUBRACKS AND ASSOCIATED PLUG-IN UNITS
    IEC 60917-2-4:2010 Modular order for the development of mechanical structures for electronic equipment practices - Part 2-4: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Adaptation dimensions for subracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in)
    EN 60917-2-4 : 2010 MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES - PART 2-4: SECTIONAL SPECIFICATION - INTERFACE COORDINATION DIMENSIONS FOR THE 25 MM EQUIPMENT PRACTICE - ADAPTATION DIMENSIONS FOR SUBRACKS OR CHASSIS APPLICABLE IN CABINETS OR RACKS IN ACCORDANCE WITH IEC 60297-3-100 (19 IN)
    IEC 60917-2-2:1994 Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 2: Detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units
    EN 60917-2-1 : 1995 MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES - PART 2: SECTIONAL SPECIFICATION - INTERFACE CO-ORDINATION DIMENSIONS FOR THE 25 MM EQUIPMENT PRACTICE - SECTION 1: DETAIL SPECIFICATION - DIMENSIONS FOR CABINETS AND RACKS
    IEC 60297-3-100:2008 Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets
    IEC 60917-1:1998+AMD1:2000 CSV Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective