• There are no items in your cart

I.S. EN 60384-14:2016

Current

Current

The latest, up-to-date edition.

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT - PART 14: SECTIONAL SPECIFICATION - FIXED CAPACITORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION AND CONNECTION TO THE SUPPLY MAINS

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2016

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.


Dates of withdrawal of national standards are available from NSAI.

National Foreword
FOREWORD
1 General
2 Preferred ratings and characteristics
3 Assessment procedures
4 Test and measurement procedures
Annex A (normative) - Circuit for the impulse voltage
        test
Annex B (normative) - Circuit for the endurance test
Annex C (normative) - Circuit for the charge and
        discharge test
Annex D (normative) - Declaration of design (confidential
        to the manufacturer and the certification body)
Annex E (informative) - Pulse test circuits
Annex F (normative) - Particular requirements for
        safety test of surface-mounting capacitors
Annex G (informative) - Capacitance ageing of fixed
        capacitors of ceramic dielectric, Class 2
Annex H (normative) - Use of safety approved a.c.
        rated capacitors in d.c. applications
Annex I (normative) - Humidity robustness grades for
        applications, where high stability under high
        humidity operating conditions is required
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Pertains to capacitors and resistor-capacitor combinations which will be connected to an a.c. mains or other supply with nominal voltage not exceeding 1000 V a.c. (r.m.s.) or 1000 V d.c. and with a nominal frequency not exceeding 100 Hz.

DevelopmentNote
Supersedes I.S. EN 132400. (10/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
DocumentType
Standard
Pages
150
PublisherName
National Standards Authority of Ireland
Status
Current
Supersedes

IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
IEC 61193-2:2007 Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages
IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
EN 60065:2014/AC:2017-01 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
EN 60068-1:2014 Environmental testing - Part 1: General and guidance
EN 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
IEC 61210:2010 Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements
IEC 60384-1:2016 Fixed capacitors for use in electronic equipment - Part 1: Generic specification
IEC 60940:2015 Guidance information on the application of capacitors, resistors, inductors and complete filter units for electromagnetic interference suppression
EN 60068-2-17:1994 Environmental testing - Part 2: Tests - Test Q: Sealing
IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
EN 61193-2 : 2007 QUALITY ASSESSMENT SYSTEMS - PART 2: SELECTION AND USE OF SAMPLING PLANS FOR INSPECTION OF ELECTRONIC COMPONENTS AND PACKAGES
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 60063:2015 Preferred number series for resistors and capacitors
EN 61210:2010 Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements
IEC 60384-14-3:2004 Fixed capacitors for use in electronic equipment - Part 14-3: Blank detail specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains - Assessment level DZ
CISPR 17:2011 Methods of measurement of the suppression characteristics of passive EMC filtering devices
EN 60384-1:2016 Fixed capacitors for use in electronic equipment - Part 1: Generic specification
ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
EN 55017 : 2011 METHODS OF MEASUREMENT OF THE SUPPRESSION CHARACTERISTICS OF PASSIVE EMC FILTERING DEVICES (CISPR 17:2011)
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
HD 243 : S12 GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT - INDEX, SURVEY AND COMPILATION OF THE SINGLE SHEETS
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests

€88.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.