I.S. EN 60534-7:2010
Current
The latest, up-to-date edition.
INDUSTRIAL-PROCESS CONTROL VALVES - PART 7: CONTROL VALVE DATA SHEET
Hardcopy , PDF
English
01-01-2010
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Application
5 General requirements sheet
6 Preparation of data sheet
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Specifies a list of requirements that are normally necessary for the procurement of the majority of control valves for process systems.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 60534-7:2010 | Identical |
| IEC 60534-7:2010 | Identical |
| EN 60534-8-3:2011 | Industrial-process control valves - Part 8-3: Noise considerations - Control valve aerodynamic noise prediction method |
| EN 60534-8-4:2015 | Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow |
| EN 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| IEC 60534-3-3:1998 | Industrial-process control valves - Part 3-3: Dimensions End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves |
| EN 60534-2-4 : 2009 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 2-4: FLOW CAPACITY - INHERENT FLOW CHARACTERISTICS AND RANGEABILITY |
| IEC 60534-3-1:2000 | Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves |
| EN 60534-2-5:2003 | Industrial-process control valves - Part 2-5: Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery |
| IEC 60534-8-1:2005 | Industrial-process control valves - Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves |
| IEC 60534-2-5:2003 | Industrial-process control valves - Part 2-5: Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery |
| EN 60534-4 : 2006 | Industrial-process control valves - Part 4: Inspection and routine testing |
| EN 60534-8-1:2005 | Industrial-process control valves - Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 60534-2-1:2011/AC:2015 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 2-1: FLOW CAPACITY - SIZING EQUATIONS FOR FLUID FLOW UNDER INSTALLED CONDITIONS (IEC 60534-2-1:2011) |
| IEC 60534-3-2:2001 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves |
| EN 60534-3-2:2001 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves |
| IEC 60534-4:2006 | Industrial-process control valves - Part 4: Inspection and routine testing |
| IEC 60534-8-4:2015 | Industrial-process control valves - Part 8-4: Noise considerations - Prediction of noise generated by hydrodynamic flow |
| EN 60534-5:2004 | Industrial-process control valves - Part 5: Marking |
| EN 60534-3-1:2000/corrigendum:2000 | INDUSTRIAL-PROCESS CONTROL VALVES - PART 3-1: DIMENSIONS - FACE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, STRAIGHT PATTERN AND CENTRE-TO-FACE DIMENSIONS FOR FLANGED, TWO-WAY, GLOBE-TYPE, ANGLE PATTERN CONTROL VALVES |
| IEC 60534-2-1:2011 | Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions |
| EN 60534-3-3:1998 | Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves |
| IEC 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
| IEC 60534-5:2004 | Industrial-process control valves - Part 5: Marking |
| IEC 60534-8-3:2010 | Industrial-process control valves - Part 8-3: Noise considerations - Control valve aerodynamic noise prediction method |
| IEC 60534-2-4:2009 | Industrial-process control valves - Part 2-4: Flow capacity - Inherent flow characteristics and rangeability |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.