Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 60544-2:2012

    Current The latest, up-to-date edition.

    ELECTRICAL INSULATING MATERIALS - DETERMINATION OF THE EFFECTS OF IONIZING RADIATION ON INSULATING MATERIALS - PART 2: PROCEDURES FOR IRRADIATION AND TEST (IEC 60544-2:2012 (EQV))

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2012

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Irradiation
    4 Test
    5 Report
    Annex A (informative) - Examples of test reports
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Defines the controls maintained over the exposure conditions during and after the irradiation of insulating materials with ionizing radiation prior to the determination of radiation-induced changes in physical or chemical properties.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    EN 60544-1:2013 Electrical insulating materials - Determination of the effects of ionizing radiation - Part 1: Radiation interaction and dosimetry
    IEC 60212:2010 Standard conditions for use prior to and during the testing of solid electrical insulating materials
    EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
    IEC 60544-4:2003 Electrical insulating materials - Determination of the effects of ionizing radiation - Part 4: Classification system for service in radiation environments
    HD 429 : 200S1 METHODS OF TEST FOR VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS
    IEC 60167:1964 Methods of test for the determination of the insulation resistance of solid insulating materials
    IEC 60544-1:2013 Electrical insulating materials - Determination of the effects of ionizing radiation - Part 1: Radiation interaction and dosimetry
    HD 568 : 200S1 METHODS OF TEST FOR THE DETERMINATION OF THE INSULATION RESISTANCE OF SOLID INSULATING MATERIALS
    IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    EN 60243-1:2013 ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013)
    IEC 60544-3:1979 Guide for determining the effects of ionizing radiation on insulating materials - Part 3: Test procedures for permanent effects
    EN 60544-4:2003 Electrical insulating materials - Determination of the effects of ionizing radiation - Part 4: Classification system for service in radiation environments
    ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
    EN ISO 868:2003 Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003)
    ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)
    ISO 178:2010 Plastics Determination of flexural properties
    EN 60212:2011 Standard conditions for use prior to and during the testing of solid electrical insulating materials
    ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective