• I.S. EN 60695-11-10:2013

    Current The latest, up-to-date edition.

    FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS (IEC 60695-11-10:2013 (EQV))

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Significance of the fire tests
    6 Apparatus
    7 Test specimens
    8 Test method A - Horizontal burning test
    9 Test method B - Vertical burning test
    Annex A (informative) - Precision of test method A
    Annex B (informative) - Precision of test method B
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Defines small-scale laboratory test procedures intended to compare the burning behaviour of different materials used in electrotechnical products when vertically or horizontally oriented test bar specimens are exposed to a small flame ignition source with a nominal thermal power of 50 W.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
    IEC 60695-11-4:2011 FIRE HAZARD TESTING - PART 11-4: TEST FLAMES - 50 W FLAME - APPARATUS AND CONFIRMATIONAL TEST METHOD
    ISO 293:2004 Plastics Compression moulding of test specimens of thermoplastic materials
    IEC 60695-1-30:2017 FIRE HAZARD TESTING - PART 1-30: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - PRESELECTION TESTING PROCESS - GENERAL GUIDELINES
    IEC 60695-4:2012 FIRE HAZARD TESTING - PART 4: TERMINOLOGY CONCERNING FIRE TESTS FOR ELECTROTECHNICAL PRODUCTS
    ISO 845:2006 Cellular plastics and rubbers Determination of apparent density
    EN ISO 9773:1998/A1:2003 Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source - Amendment 1: Specimens (ISO 9773:1998/Amd 1:2003)
    ISO 9773:1998 Plastics Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source
    ISO 295:2004 Plastics Compression moulding of test specimens of thermosetting materials
    ISO 13943:2017 Fire safety Vocabulary
    EN ISO 293 : 2005 PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOPLASTIC MATERIALS
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    EN 60695-11-4 : 2011 FIRE HAZARD TESTING - PART 11-4: TEST FLAMES - 50 W FLAME - APPARATUS AND CONFIRMATIONAL TEST METHOD (IEC 60695-11-4:2011)
    EN 60695-4:2012 FIRE HAZARD TESTING - PART 4: TERMINOLOGY CONCERNING FIRE TESTS FOR ELECTROTECHNICAL PRODUCTS (IEC 60695-4:2012)
    EN ISO 307:2007/A1:2013 PLASTICS - POLYAMIDES - DETERMINATION OF VISCOSITY NUMBER (ISO 307:2007/AMD 1:2013)
    ISO 9772:2012 Cellular plastics Determination of horizontal burning characteristics of small specimens subjected to a small flame
    IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
    EN ISO 295 : 2004 PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS
    ISO 307:2007 Plastics Polyamides Determination of viscosity number
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    EN ISO 291:2008 PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING AND TESTING
    IEC 60695-1-11:2014 Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment
    IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
    ISO 1043-1:2011 Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics
    IEC 60695-1-10:2016 FIRE HAZARD TESTING - PART 1-10: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - GENERAL GUIDELINES
    ISO 16012:2015 Plastics Determination of linear dimensions of test specimens
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective