I.S. EN 60695-11-20:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FIRE HAZARD TESTING - PART 11-20: TEST FLAMES - 500 W FLAME TEST METHODS
Hardcopy , PDF
23-11-2021
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Significance of the fire tests
6 Apparatus
7 Test specimens
8 Test procedure
Annex A (normative) - Detailed requirements for the
flame application point
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Explains a test method consisting of two small-scale laboratory test procedures which is intended to compare the burning behaviour of different materials used in electrotechnical products.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
76
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| SN EN 60695-11-20 : 1999 AMD 1 2003 | Identical |
| BS EN 60695-11-20:2015 | Identical |
| DIN EN 60695-11-20 : 2016 | Identical |
| UNE-EN 60695-11-20:2016 | Identical |
| EN 60695-11-20:2015 | Identical |
| NF EN 60695-11-20 : 2015 | Identical |
| EN 60695-11-20:2015/AC:2016 | Identical |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| IEC 60695-1-30:2017 | Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines |
| IEC 60695-4:2012 | Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical products |
| ISO 845:2006 | Cellular plastics and rubbers — Determination of apparent density |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 13943:2017 | Fire safety — Vocabulary |
| EN ISO 293:2005 | Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004) |
| EN ISO 845:2009 | Cellular plastics and rubbers - Determination of apparent density (ISO 845:2006) |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| EN 60695-4:2012 | FIRE HAZARD TESTING - PART 4: TERMINOLOGY CONCERNING FIRE TESTS FOR ELECTROTECHNICAL PRODUCTS (IEC 60695-4:2012) |
| EN 60695-11-3:2012 | Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods |
| IEC GUIDE 104:2010 | The preparation of safety publications and the use of basic safety publications and group safety publications |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN ISO 295:2004 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| IEC 60695-11-3:2012 | Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| EN ISO 13943:2017 | Fire safety - Vocabulary (ISO 13943:2017) |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
| IEC 60695-1-11:2014 | Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment |
| IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| IEC 60695-1-10:2016 | Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines |
| ISO 16012:2015 | Plastics Determination of linear dimensions of test specimens |
| EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
| EN ISO 294-3:2003 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.