• I.S. EN 60695-2-10:2013

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    FIRE HAZARD TESTING - PART 2-10: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE APPARATUS AND COMMON TEST PROCEDURE (IEC 60695-2-10:2013 (EQV))

    Available format(s):  Hardcopy, PDF

    Superseded date:  03-01-2022

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Description of the test apparatus
    5 Verification of the apparatus
    6 Conditioning
    7 Common test procedure
    Annex A (informative) - Equipment manufacturers and suppliers
    Annex B (informative) - Guidance on 'ignition' and 'flaming'
            observations
    Annex C (informative) - Guidance on the verification procedure
            of the glow-wire temperature measuring system by
            the heating current
    Bibliography
    Annex ZA (normative) - Normative references to international
             Publications with their corresponding
             European publications

    Abstract - (Show below) - (Hide below)

    Defines the glow-wire apparatus and common test procedure to simulate the effects of thermal stresses which may be produced by heat sources such as glowing elements or overloaded resistors, for short periods, in order to assess the fire hazard by a simulation technique.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 60695-2-1-0. (05/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60584-2 : 1993 THERMOCOUPLES - PART 2: TOLERANCES (IEC 584-2:1982 + A1:1989)
    ISO 13943:2017 Fire safety Vocabulary
    IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
    IEC 60695-2-13:2010+AMD1:2014 CSV Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials
    EN 60695-2-13:2010/A1:2014 FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014)
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    IEC 60695-2-12:2010+AMD1:2014 CSV Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials
    IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
    EN 60584-1:2013 THERMOCOUPLES - PART 1: EMF SPECIFICATIONS AND TOLERANCES (IEC 60584-1:2013)
    EN ISO 13943:2017 Fire safety - Vocabulary (ISO 13943:2017)
    ISO 4046-4:2002 Paper, board, pulps and related terms Vocabulary Part 4: Paper and board grades and converted products
    IEC 60695-1-11:2014 Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment
    EN 60695-2-12:2010/A1:2014 FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014)
    IEC 60695-1-10:2016 Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
    IEC 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
    EN 60695-2-11:2014 FIRE HAZARD TESTING - PART 2-11: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY TEST METHOD FOR END-PRODUCTS (GWEPT) (IEC 60695-2-11:2014)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective