I.S. EN 60793-2-60:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
OPTICAL FIBRES - PART 2-60: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY C SINGLE-MODE INTRACONNECTION FIBRES
Hardcopy , PDF
English
01-01-2008
02-03-2026
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
FOREWORD
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Symbols and abbreviations
4 Specifications
4.1 Dimensional requirements
4.2 Mechanical requirements
4.3 Transmission requirements
4.4 Environmental requirements
4.4.1 Transmission requirements
4.4.2 Mechanical requirements
Annex A (normative) Family specification for C1 single-mode fibre
Annex B (normative) Family specification for C2 single-mode fibre
Annex C (normative) Family specification for C3 single-mode fibre
Annex D (normative) Family specification for C4 single-mode fibre
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Bibliography
Applies to optical fibre types C1, C2, C3, C4, as described in Table 1. These fibres are used for the intraconnections within or between components or photonic systems or subsystems.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| IEC 60793-2-60:2008 | Identical |
| EN 60793-2-60:2008 | Identical |
| BS EN 60793-2-60:2008 | Equivalent |
| EN 60793-1-32:2010 | Optical fibres - Part 1-32: Measurement methods and test procedures - Coating strippability |
| EN 60793-1-46:2002 | Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in optical transmittance |
| EN 60793-1-21:2002 | Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry |
| EN 60793-1-20:2014/AC:2016-03 | OPTICAL FIBRES - PART 1-20: MEASUREMENT METHODS AND TEST PROCEDURES - FIBRE GEOMETRY (IEC 60793-1-20:2014/COR1:2016) |
| EN 60793-1-44:2011 | Optical fibres - Part 1-44: Measurement methods and test procedures - Cut-off wavelength |
| IEC 60793-1-44:2011 | Optical fibres - Part 1-44: Measurement methods and test procedures - Cut-off wavelength |
| EN 60793-1-30:2011 | Optical fibres - Part 1-30: Measurement methods and test procedures - Fibre proof test |
| IEC 60793-1-52:2014 | Optical fibres - Part 1-52: Measurement methods and test procedures - Change of temperature tests |
| IEC 60793-2:2015 | Optical fibres - Part 2: Product specifications - General |
| IEC 60793-1-50:2014 | Optical fibres - Part 1-50: Measurement methods and test procedures - Damp heat (steady state) tests |
| IEC 60793-1-42:2013 | Optical fibres - Part 1-42: Measurement methods and test procedures - Chromatic dispersion |
| EN 60793-1-40:2003 | Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation |
| IEC 60793-1-33:2017 | Optical fibres - Part 1-33: Measurement methods and test procedures - Stress corrosion susceptibility |
| IEC 60793-1-32:2010 | Optical fibres - Part 1-32: Measurement methods and test procedures - Coating strippability |
| IEC 60793-1-51:2014 | Optical fibres - Part 1-51: Measurement methods and test procedures - Dry heat (steady state) tests |
| EN 60793-1-22:2002 | Optical fibres - Part 1-22: Measurement methods and test procedures - Length measurement |
| EN 60793-1-50:2015 | Optical fibres - Part 1-50: Measurement methods and test procedures - Damp heat (steady state) tests |
| IEC 60793-1-46:2001 | Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in optical transmittance |
| IEC 60793-1-40:2001 | Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation |
| IEC 60793-1-45:2017 | Optical fibres - Part 1-45: Measurement methods and test procedures - Mode field diameter |
| IEC TR 61931:1998 | Fibre optic - Terminology |
| EN 60793-1-31:2010 | Optical fibres - Part 1-31: Measurement methods and test procedures - Tensile strength |
| IEC 60793-1-21:2001 | Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry |
| EN 60793-1-52:2014 | Optical fibres - Part 1-52: Measurement methods and test procedures - Change of temperature tests |
| EN 60793-1-51:2014 | Optical fibres - Part 1-51: Measurement methods and test procedures - Dry heat (steady state) tests |
| EN 60793-2:2016 | Optical fibres - Part 2: Product specifications - General |
| IEC 60793-1-47:2017 | Optical fibres - Part 1-47: Measurement methods and test procedures - Macrobending loss |
| IEC 60793-1-20:2014 | Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry |
| IEC 60793-1-53:2014 | Optical fibres - Part 1-53: Measurement methods and test procedures - Water immersion tests |
| IEC 60793-1-34:2006 | Optical fibres - Part 1-34: Measurement methods and test procedures - Fibre curl |
| IEC 60793-1-22:2001 | Optical fibres - Part 1-22: Measurement methods and test procedures - Length measurement |
| IEC 60793-1-31:2010 | Optical fibres - Part 1-31: Measurement methods and test procedures - Tensile strength |
| IEC 60793-1-30:2010 | Optical fibres - Part 1-30: Measurement methods and test procedures - Fibre proof test |
| IEC 60793-1-54:2012 | Optical fibres - Part 1-54: Measurement methods and test procedures - Gamma irradiation |
Important note : Users cannot be edited or removed once added to your Multi user PDF.