• I.S. EN 60923:2005

    Current The latest, up-to-date edition.

    AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2005

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General notes on tests
    5 Marking
    6 Ballasts designed to operate at various
       supply voltages
    7 Circuit power-factor
    8 Supply current
    9 Current waveform
       9.1 Lamp operating current waveform
       9.2 Test procedure
    10 Magnetic screening
    11 Ignitors
    12 Electrical requirements for ballasts for
       high-pressure mercury vapour lamps
       12.1 Ballast setting
       12.2 Short-circuit current
       12.3 Open-circuit voltage (minimum voltage for
            stable operation)
    13 Electrical requirements for ballasts for low-pressure
       sodium vapour lamps
       13.1 Ballast setting
       13.2 Short-circuit current and run-up conditions
       13.3 Open-circuit voltage (minimum voltage for
            stable operation)
    14 Electrical requirements for ballasts for metal
       halide lamps
       14.1 Ballast setting
       14.2 Short-circuit current and run-up conditions
       14.3 Open-circuit voltage (minimum voltage for
            stable operation)
    15 Electrical requirements for ballasts for high-pressure
       sodium vapour lamps
       15.1 Ballast setting
       15.2 Short-circuit current
       15.3 Open-circuit voltage
    Annex A (normative) Reference ballasts
    Annex B (normative) Reference lamps
    Annex C (normative) General requirements for tests
    Annex D (normative) Explanation of measurements of
                           ballast setting and lamp-operating
                           current waveform for high-pressure sodium
                           vapour lamps
    Annex E (informative) Interpretations
    Annex ZA (normative) Normative references to international
                           publications with their corresponding
                           European publications
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines performance requirements for ballasts for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps.

    General Product Information - (Show below) - (Hide below)

    Development Note To be read in conjunction with I.S. EN 60922. (02/2002) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60188 : 2001 High-pressure mercury vapour lamps - Performance specifications
    EN 60192:2001 LOW PRESSURE SODIUM VAPOUR LAMPS - PERFORMANCE SPECIFICATIONS
    IEC 61547:2009 Equipment for general lighting purposes - EMC immunity requirements
    IEC 60662:2011 High-pressure sodium vapour lamps - Performance specifications
    EN 61347-2-9:2013 LAMP CONTROLGEAR - PART 2-9: PARTICULAR REQUIREMENTS FOR ELECTROMAGNETIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) (IEC 61347-2-9:2012)
    IEC 60192:2001 Low-pressure sodium vapour lamps - Performance specifications
    IEC 60188:2001 High-pressure mercury vapour lamps - Performance specifications
    IEC 61347-2-9:2012 Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
    IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
    EN 61347-2-1:2001/A2:2014 LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS) (IEC 61347-2-1:2000/A2:2013)
    IEC 61347-2-1:2000+AMD1:2005+AMD2:2013 CSV Lamp controlgear - Part 2-1: Particular requirements for startingdevices (other than glow starters)
    IEC 61167:2015 Metal halide lamps - Performance specification
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    IEC 60921:2004+AMD1:2006 CSV Ballasts for tubular fluorescent lamps - Performance requirements
    EN 61347-1:2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS (IEC 61347-1:2015)
    IEC 60598-1:2014+AMD1:2017 CSV Luminaires - Part 1: General requirements and tests
    EN 60662:2012 HIGH-PRESSURE SODIUM VAPOUR LAMPS - PERFORMANCE SPECIFICATIONS (IEC 60662:2011, MODIFIED)
    IEC 61000-3-2 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT <= 16 A PER PHASE)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective