• I.S. EN 61000-4-25:2002

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ELECTROMAGNETIC COMPATIBILITY (EMC) - TESTING AND MEASUREMENT TECHNIQUES - HEMP IMMUNITY TEST METHODS FOR EQUIPMENT AND SYSTEMS (IEC 61000-4-25:2001 (EQV))

    Available format(s):  Hardcopy, PDF

    Superseded date:  27-03-2020

    Language(s):  English

    Published date:  01-01-2002

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION
    1 Scope
    2 Normative references
    3 Definitions
    4 General
    5 Immunity tests and immunity test levels
    6 Test equipment
    7 Test set-up
    8 Test procedure
    9 Test results and test reports
    Annex A (informative) - Rationale for the immunity test
            levels
    Annex B (informative) - Conducted immunity tests for
            antennas
    Annex C (informative) - Conducted disturbance immunity
            tests
    Annex D (informative) - Damped oscillatory wave test
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Describes the immunity test levels and related test methods for electrical and electronic equipment and systems exposed to high-altitude electromagnetic pulse (HEMP) environments.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC TR 61000-5-3:1999 Electromagnetic compatibility (EMC) - Part 5-3: Installation and mitigation guidelines - HEMP protection concepts
    IEC 60038:2009 IEC standard voltages
    VG 96903-78 : 2011 NUCLEAR ELECTROMAGNETIC PULSE (NEMP) AND LIGHTNING PROTECTION - TEST METHODS, TEST EQUIPMENT AND LIMITING VALUES - PART 78: DIRECT INJECTION OF NEMP DISTURBING QUANTITIES TO CABLES AND CABLE HARNESSES OF MULTI-APPLICATION EQUIPMENT (TEST METHOD LF 78)
    IEC 61024-1:1990 PROTECTION OF STRUCTURES AGAINST LIGHTNING - GENERAL PRINCIPLES
    IEC 61000-2-10:1998 Electromagnetic compatibility (EMC) - Part 2-10: Environment - Description of HEMP environment - Conducted disturbance
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST
    EN 61000-2-10 : 1999 Electromagnetic compatibility (EMC) - Part 2-10: Environment - Description of HEMP environment - Conducted disturbance
    EN 61000-4-11:2004/A1:2017 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017)
    IEC 61000-2-11:1999 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 2-11: ENVIRONMENT - CLASSIFICATION OF HEMP ENVIRONMENTS
    IEC 61000-4-11:2004+AMD1:2017 CSV Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests
    EN 60068-1:2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    EN 61000-2-9 : 1996 ELECTROMAGNETIC COMPATIBILITY (EMC) - ENVIRONMENT - DESCRIPTION OF HEMP ENVIRONMENT - RADIATED DISTURBANCE - BASIC EMC PUBLICATION
    IEC 61000-4-33:2005 Electromagnetic compatibility (EMC) - Part 4-33: Testing and measurement techniques - Measurement methods for high-power transient parameters
    MIL STD 461 : G REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC INTERFERENCE CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT
    IEC 61000-4-20:2010 Electromagnetic compatibility (EMC) - Part 4-20: Testing and measurement techniques - Emission and immunity testing in transverse electromagnetic (TEM) waveguides
    VG 96903-70 : 2011 NUCLEAR ELECTROMAGNETIC PULSE (NEMP) AND LIGHTNING PROTECTION - TEST METHODS, TEST EQUIPMENT AND LIMITING VALUES - PART 70: DIRECT INJECTION OF NEMP DISTURBING QUANTITIES INTO LINE TERMINALS OF MULTI-APPLICATION EQUIPMENT (TEST METHOD LF 70)
    ISO 7137:1995 Aircraft Environmental conditions and test procedures for airborne equipment
    IEC 61000-2-9:1996 ELECTROMAGNETIC COMPATIBILITY (EMC) - ENVIRONMENT - DESCRIPTION OF HEMP ENVIRONMENT - RADIATED DISTURBANCE - BASIC EMC PUBLICATION
    EN 61000-4-4:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012)
    EN 61000-4-13:2002/A2:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002/A2:2015)
    IEC 61000-4-18:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 4-18: Testing and measurement techniques - Damped oscillatory wave immunity test
    IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests
    EN 61000-4-20:2010 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-20: TESTING AND MEASUREMENT TECHNIQUES - EMISSION AND IMMUNITY TESTING IN TRANSVERSE ELECTROMAGNETIC (TEM) WAVEGUIDES
    EN 60038 : 2011 CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective