• I.S. EN 61076-3-114:2009

    Current The latest, up-to-date edition.

    CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-114: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR FREQUENCIES UP TO 600 MHZ FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 11 RELATED TO IEC 61076-3-106 - BAYONET COUPLING TYPE

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION
    1 General data
      1.1 Scope
      1.2 Normative references
    2 Terms and definitions
    3 Dimensional information
      3.1 Common features
      3.2 General
      3.3 Contact arrangement of all connector types
      3.4 IP65 and IP67 sealing
      3.5 Industrial IEC 60603-7 variant 11 - Bayonet coupling
      3.6 Termination and mounting information
      3.7 General
      3.8 Mounting information for variant 11, fixed connector
      3.9 Cap for fixed connector
      3.10 Cap for free connector
    4 Gauges
      4.1 Connectors, IEC 60603-7 interface
    5 Characteristics
      5.1 Climatic category
      5.2 Electrical
      5.3 Transmission characteristics
    6 Test schedule
      6.1 General
      6.2 Test procedures and measuring methods
      6.3 Preconditioning
      6.4 Wiring and mounting of specimens
      6.5 Arrangement for contact resistance test
      6.6 Arrangement for dynamic stress tests (test phase AP2)
      6.7 Basic (minimum) test schedule
      6.8 Full test schedule
      Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Specifies protective housings for upgrading existing 8-way shielded and unshielded connectors utilizing the interface described in IEC 60603-7-2, IEC 60603-7-3, IEC 60603-7-4, IEC 60603-7-5, and IEC 60603-7-7 to IP65 and IP67 ratings according to IEC 60529, for use in industrial environments.

    General Product Information - (Show below) - (Hide below)

    Committee SR 48B
    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61076-1:2006 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
    EN 60603-7-7:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-7: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 600 MHZ
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    EN 60512-1-100 : 2012 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 1-100: GENERAL - APPLICABLE PUBLICATIONS (IEC 60512-1-100:2012)
    IEC 60603-7-2:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-2: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 100 MHZ
    MIL DTL 26482 : H CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, QUICK DISCONNECT, ENVIRONMENT RESISTING, RECEPTACLES AND PLUGS, GENERAL SPECIFICATION FOR
    EN 60068-1 : 2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    EN 60512-1 : 2001 ELECTROMECHANICAL COMPONENTS FOR ELECTRONIC EQUIPMENT - BASIC TESTING PROCEDURES AND MEASURING METHODS - PART 1: GENERAL
    EN 61076-1 : 2006 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
    IEC 61156-2:2010 MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS - PART 2: SYMMETRICAL PAIR/QUAD CABLES WITH TRANSMISSION CHARACTERISTICS UP TO 100 MHZ - HORIZONTAL FLOOR WIRING - SECTIONAL SPECIFICATION
    IEC 60603-7-3:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-3: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 100 MHZ
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60603-7:2008+AMD1:2011 CSV Connectors for electronic equipment - Part 7: Detail specification for 8-way, unshielded, free and fixed connectors
    IEC 60512-1-100:2012 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 1-100: GENERAL - APPLICABLE PUBLICATIONS
    EN 60664-1 : 2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    EN 60603-7-4 : 2010 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-4: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ
    IEC 61156-4:2009 MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS - PART 4: RISER CABLES - SECTIONAL SPECIFICATION
    IEC 60603-7-5:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-5: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ
    IEC 61156-3:2008 MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS - PART 3: WORK AREA CABLE - SECTIONAL SPECIFICATION
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    IEC 60512-1:2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 1: GENERAL
    EN 60068-2-30 : 2005 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    IEC 60603-7-7:2010 Connectors for electronic equipment - Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN 60068-2-14 : 2009 ENVIRONMENTAL TESTING - PART 2-14: TESTS - TEST N: CHANGE OF TEMPERATURE
    IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
    IEC 60603-7-4:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-4: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS, FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 250 MHZ
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective