Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 61300-1:2016

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - BASIC TEST AND MEASUREMENT PROCEDURES - PART 1: GENERAL AND GUIDANCE

    Available format(s):  Hardcopy, PDF

    Superseded date:  22-06-2022

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions and abbreviations
    4 Requirements for the IEC 61300-2 series and
       the IEC 61300-3 series
    5 Standard atmospheric conditions
    6 Significance of the numerical value of a quantity
    7 Graphical symbols and terminology
    8 Safety
    9 Calibration
    10 Launch conditions
    Annex A (normative) - Multimode launch condition
            requirement for measuring attenuation of
            components terminated on IEC 60793-2-10 type
            A1a and A1b fibres
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Defines general information and guidance for the basic test and measurement procedures defined in the IEC 61300-2 and IEC 61300-3 series for interconnecting devices and passive components.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 61300-3-53:2015 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-53: Examinations and measurements - Encircled angular flux (EAF) measurement method based on two-dimensional far field data from step index multimode waveguide (including fibre)
    IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS)
    IEC TR 62614-2:2015 Fibre optics - Multimode launch conditions - Part 2: Determination of launch condition requirements for measuring multimode attenuation
    IEC 60050-731:1991 International Electrotechnical Vocabulary (IEV) - Part 731: Optical fibre communication
    EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
    IEC 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
    EN 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    IEC 60793-2-30:2015 Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres
    EN 60793-2-40:2016 Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres
    IEC 60793-2-40:2015 Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres
    IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
    EN 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
    EN 61300-3-1:2005 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-1: Examinations and measurements - Visual examination
    IEC 61280-4-1:2009 Fibre-optic communication subsystem test procedures - Part 4-1: Installed cable plant - Multimode attenuation measurement
    EN 60793-2-30:2015 Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres
    IEC 61300-3-35:2015 RLV Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-35: Examinations and measurements - Visual inspection of fibre optic connectors and fibre-stub transceivers
    EN 61280-1-4:2010 Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method
    EN 61300-3-35:2015 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-35: Examinations and measurements - Visual inspection of fibre optic connectors and fibre-stub transceivers
    IEC 61315:2005 Calibration of fibre-optic power meters
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    EN 61280-4-1:2009 FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT
    EN 60825-2:2004/A2:2010 SAFETY OF LASER PRODUCTS - PART 2: SAFETY OF OPTICAL FIBRE COMMUNICATION SYSTEMS (OFCS)
    IEC 62614:2010 Fibre optics - Launch condition requirements for measuring multimode attenuation
    EN 61315:2006 Calibration of fibre-optic power meters
    EN 62614 : 2010 FIBRE OPTICS - LAUNCH CONDITION REQUIREMENTS FOR MEASURING MULTIMODE ATTENUATION
    IEC 61300-3-1:2005 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-1: Examinations and measurements - Visual examination
    IEC 61280-1-4:2009 Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective