Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 61319-1:1999

    Current The latest, up-to-date edition.

    INTERCONNECTIONS OF SATELLITE RECEIVING EQUIPMENT - PART 1: EUROPE

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-1999

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Explanation of terms and abbreviations
    4 Interface requirements for polarizers and
      polarswitchers
      4.1 Mechanical polarizers (optional)
      4.2 Magnetic polarizers (using the Faraday effect)
           4.2.1 Polarizers for two orthogonal polarizations
           4.2.2 Polarizers for four polarizations
      4.3 Polarswitchers
    5 Interface requirements for low-noise block
      converters (LNB)
      5.1 Characteristic impedance of the first intermediate
           frequency (IF) output
      5.2 Interface between the LNB (outdoor part) and the satellite
           receiver (indoor part), case 1: one IF input signal and
           one two-state control command
           5.2.1 Single-band block converters
           5.2.2 Dual-band block converters
           5.2.3 Combination of dual-band block converter with
                 polarswitcher
      5.3 Interface between the LNB (outdoor part) and the
           satellite
           receiver (indoor part) case 2: two IF input signals and
           internal two-state control command
      5.4 Connectors
    6 Interface requirements for switching between different antenna
      sources or antenna positions
      6.1 Electrical matching values for the actuator motor supply
      6.2 Electrical matching values for the antenna position sensor
      6.3 Interface between the antenna position control unit and
           the satellite receiver
           6.3.1 Circular connector
           6.3.2 Domestic Digital Bus (D2B)
    7 Interface requirements for satellite receivers and external
      decoders, descramblers and conditional access systems
    8 Interface requirements for Digital Satellite Radio (DSR)
      receivers
      8.1 Configuration of receiving equipment
           8.1.1 Direct reception of radio only
           8.1.2 Direct reception of radio and television
           8.1.3 Cable reception
      8.2 Audio-frequency outputs of DSR receivers
    Annex A (informative) Interconnections between a satellite
                          receiver and a decoder
    Annex ZA (normative) Normative references to international
                          publications with their corresponding
                          European publications
    Annex ZB (normative) Communication between the satellite
                          receiver and the peripheral equipment using
                          the Digital Satellite Equipment Control
                          bus (DiSEqC)
      ZB.1 Scope
      ZB.2 Normative references
      ZB.3 Basic principle of the extended signalling method
      ZB.4 Typical applications
      ZB.5 Combination of conventional and new signalling messages
      ZB.6 Simple Tone Burst control signal
      ZB.7 Method of data bit signalling
      ZB.8 Structure of a DiSEqC message
      ZB.9 Cascaded DiSEqC devices
      ZB.10 Power management
      ZB.11 Reset at power set-up
      ZB.12 Reset when using loop-through tuners
      ZB.13 D.C. voltage rise and settling time
      ZB.14 Time sequences for DiSEqC messages
      ZB.15 Frequency allocation of the local oscillators
      ZB.16 Characteristics of the signalling d.c. voltage
      ZB.17 Characteristics of the 22 kHz signalling tone
      ZB.18 Transport of the 22 kHz tone
      ZB.19 IPR, trademark and logo
    Figures

    Abstract - (Show below) - (Hide below)

    Covers standardization of interconnections and matching values for satellite receivers for individual television and sound radio broadcast reception in the 10,70 GHz to 12,75 GHz band.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 61030:1993 Audio, video and audiovisual systems - Domestic Digital Bus (D2B)
    EN 60065:2014/AC:2017-01 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
    HD 134.2 : 200S2 RADIO-FREQUENCY CONNECTORS - COAXIAL UNMATCHED CONNECTOR
    IEC 60169-2:1965 Radio-frequency connectors. Part 2: Coaxial unmatched connector
    IEC 60130-9:2011 Connectors for frequencies below 3 MHz - Part 9: Circular connectors for radio and associated sound equipment
    HD 483.15 : 200S4 SOUND SYSTEM EQUIPMENT - PREFERRED MATCHING VALUES FOR THE INTERCONNECTION OF SOUND SYSTEM COMPONENTS
    HD 483.11 : 200S3 SOUND SYSTEM EQUIPMENT - APPLICATION OF CONNECTORS FOR THE INTERCONNECTION OF SOUND SYSTEM COMPONENTS
    IEC 60933-4:1994 Audio, video and audiovisual systems - Interconnections and matching values - Part 4: Connector and cordset for domestic digital bus (D2B)
    IEC 60958:1989 Digital audio interface
    EN 60933-4:1994 Audio, video and audiovisual systems - Interconnections and matching values - Part 4: Connector and cordset for domestic digital bus (D2B)
    IEC 60268-15:1996 Sound system equipment - Part 15: Preferred matching values for the interconnection of sound system components.
    EN 60130-9:2011 Connectors for frequencies below 3 MHz - Part 9: Circular connectors for radio and associated sound equipment
    IEC 61030:1991 Audio, video and audiovisual systems - Domestic Digital Bus (D2B)
    EN 60169-24:1993 Radio-frequency connectors - Part 24: Radio-frequency coaxial connectors with screw coupling, typically for use in 75 ohm cable distribution systems (Type F)
    IEC 60169-24:1991 Radio-frequency connectors - Part 24: Radio-frequency coaxial connectors with screw coupling, typically for use in 75 ohm cable distribution systems (Type F)
    EN 60958:1990/A2:1995 DIGITAL AUDIO INTERFACE
    IEC 60268-11:1987 Sound system equipment. Part 11: Application of connectors for the interconnection of sound system components
    IEC 60807-9:1993 Rectangular connectors for frequencies below 3 MHz - Part 9: Detail specification for a range of peritelevision connectors
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective