• I.S. EN 61851-1:2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 1: GENERAL REQUIREMENTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  26-07-2019

    Language(s):  English

    Published date:  01-01-2011

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General requirements
    5 Rating of the supply a.c. voltage
    6 General system requirement and interface
    7 Protection against electric shock
    8 Connection between the power supply and the EV
    9 Specific requirements for vehicle inlet,
       connector, plug and socket-outlet
    10 Charging cable assembly requirements
    11 EVSE requirements
    Annex A (normative) - Pilot function through a control pilot
            circuit using PWM modulation and a control pilot wire
    Annex B (informative) - Example of a circuit diagram for a
            basic and universal vehicle coupler
    Annex C (informative) - Example of a method that provides the
            pilot function equivalent to a hard wired system
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding European
             publications
    Annex ZB (normative) - Special national conditions

    Abstract - (Show below) - (Hide below)

    Pertains to on-board and off-board equipment for charging electric road vehicles at standard a.c. supply voltages (as per IEC 60038) up to 1000 V and at d.c. voltages up to 1500 V, and for providing electrical power for any additional services on the vehicle if required when connected to the supply network.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017) 2011 Edition is Partially Superseded by I.S. EN 62752. (07/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    IEC 60038:2009 IEC standard voltages
    IEC 60245-2:1994+AMD1:1997+AMD2:1997 CSV Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 2: Test methods
    PREN 61009-1 : DRAFT 2011 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCBOS) - PART 1: GENERAL RULES
    ISO 6469-2:2009 Electrically propelled road vehicles Safety specifications Part 2: Vehicle operational safety means and protection against failures
    IEC 60245-1:2003+AMD1:2007 CSV Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 1: General requirements
    EN 60068-2-75 : 2014 ENVIRONMENTAL TESTING - PART 2-75: TESTS - TEST EH: HAMMER TESTS (IEC 60068-2-75:2014)
    EN 61000-6-1 : 2007 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS
    IEC 61540:1997+AMD1:1998 CSV Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)
    PREN 61008-1 : DRAFT 2011 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCBS) - PART 1: GENERAL RULES
    IEC 60245-6:1994 RUBBER INSULATED CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V - PART 6: ARC WELDING ELECTRODE CABLES
    IEC 62196-2:2016 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
    EN 61000-6-3:2007/A1:2011/AC:2012 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010)
    PREN 60038 : DRAFT 2011 CENELEC STANDARD VOLTAGES
    IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
    IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV Plugs and socket-outlets for household and similar purposes - Part1: General requirements
    IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules
    IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
    HD 60364-4-41:2017/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK
    EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
    IEC 61000-6-1 : 3.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS
    IEC 62335:2008 Circuit breakers - Switched protective earth portable residual current devices for class I and battery powered vehicle applications
    IEC 61851-22:2001 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: AC ELECTRIC VEHICLE CHARGING STATION
    EN 62196-1 : 2014 PLUGS, SOCKET-OUTLETS, VEHICLE CONNECTORS AND VEHICLE INLETS - CONDUCTIVE CHARGING OF ELECTRIC VEHICLES - PART 1: GENERAL REQUIREMENTS (IEC 62196-1:2014, MODIFIED)
    IEC 60050-442:1998 International Electrotechnical Vocabulary (IEV) - Part 442: Electrical accessories
    IEC 61009-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers with integral overcurrentprotection for household and similar uses (RCBOs) - Part 1: General rules
    EN 60947-3:2009/A2:2015 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS (IEC 60947-3:2008/A2:2015)
    IEC 61000-6-3:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
    IEC 60364-6:2016 Low voltage electrical installations - Part 6: Verification
    SAE J 1772 : 2016 SAE ELECTRIC VEHICLE AND PLUG IN HYBRID ELECTRIC VEHICLE CONDUCTIVE CHARGE COUPLER
    IEC TR 60755:2008 General requirements for residual current operated protective devices
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60245-4:2011 RUBBER INSULATED CABLES - RATED VOLTAGES UP TO AND INCLUDING 450/750 V - PART 4: CORDS AND FLEXIBLE CABLES
    IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
    IEC 60884-2-5:2017 Plugs and socket-outlets for household and similar purposes - Part 2-5: Particular requirements for adaptors
    EN 60664-1 : 2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    EN 60068-2-78 : 2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012)
    IEC 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
    ISO 6469-3:2011 Electrically propelled road vehicles Safety specifications Part 3: Protection of persons against electric shock
    IEC 60947-3:2008+AMD1:2012+AMD2:2015 CSV Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
    EN 50065-1 : 2011 SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 1: GENERAL REQUIREMENTS, FREQUENCY BANDS AND ELECTROMAGNETIC DISTURBANCES
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    IEC 61180-1:1992 High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    EN 60068-2-30 : 2005 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
    IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
    EN 60276 : 1996 DEFINITIONS AND NOMENCLATURE FOR CARBON BRUSHES, BRUSH-HOLDERS, COMMUTATORS AND SLIP-RINGS
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements
    IEC 60947-6-1:2005+AMD1:2013 CSV Low-voltage switchgear and controlgear - Part 6-1: Multiple functionequipment - Transfer switching equipment
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    EN 60309-2:1999/A2:2012 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES (IEC 60309-2:1999/A2:2012)
    IEC 60309-2:1999+AMD1:2005+AMD2:2012 CSV PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES
    EN 61180-1 : 1994 HIGH-VOLTAGE TEST TECHNIQUES FOR LOW-VOLTAGE EQUIPMENT - PART 1: DEFINITIONS, TEST AND PROCEDURE REQUIREMENTS
    IEC 61851-21:2001 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 21: ELECTRIC VEHICLE REQUIREMENTS FOR CONDUCTIVE CONNECTION TO AN A.C./D.C. SUPPLY
    IEC 60990:2016 Methods of measurement of touch current and protective conductor current
    EN 60309-1:1999/A1:2007/AC:2014 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60309-1:1999/A2:2012)
    IEC 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements
    EN 60990 : 2016 METHODS OF MEASUREMENT OF TOUCH CURRENT AND PROTECTIVE CONDUCTOR CURRENT (IEC 60990:2016)
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective