• I.S. EN 62282-3-200:2016

    Current The latest, up-to-date edition.

    FUEL CELL TECHNOLOGIES - PART 3-200: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions, operating process and symbols
    4 Reference conditions
    5 Item of performance test
    6 Test preparation
    7 Measurement instruments and measurement
       methods
    8 Test plan
    9 Test methods and computation of test results
    10 Test reports
    Annex A (normative) - Uncertainty analysis
    Annex B (normative) - Calculation of fuel heating
            value
    Annex C (normative) - Reference gas
    Annex D (informative) - Maximum acceptable instantaneous
            electric power output transient
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Defines operational and environmental aspects of the stationary fuel cell power systems performance.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 62282-3-2. (01/2012) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TR 15916:2015 Basic considerations for the safety of hydrogen systems
    EN 60688:2013 ELECTRICAL MEASURING TRANSDUCERS FOR CONVERTING A.C. AND D.C. ELECTRICAL QUANTITIES TO ANALOGUE OR DIGITAL SIGNALS (IEC 60688:2012)
    IEC 61672-2:2013+AMD1:2017 CSV Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests
    EN ISO 11541 : 2002 NATURAL GAS - DETERMINATION OF WATER CONTENT AT HIGH PRESSURE
    ISO 3648:1994 Aviation fuels Estimation of net specific energy
    ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
    ISO 6976:2016 Natural gas Calculation of calorific values, density, relative density and Wobbe indices from composition
    ISO 14687-3:2014 Hydrogen fuel Product specification Part 3: Proton exchange membrane (PEM) fuel cell applications for stationary appliances
    EN 60359 : 2002 ELECTRICAL AND ELECTRONIC MEASUREMENT EQUIPMENT - EXPRESSION OF PERFORMANCE
    EN 61672-2:2013/A1:2017 ELECTROACOUSTICS - SOUND LEVEL METERS - PART 2: PATTERN EVALUATION TESTS (IEC 61672-2:2013/A1:2017)
    ISO 11086:1996 Gas turbines Vocabulary
    IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
    IEC TS 62282-1:2013 Fuel cell technologies - Part 1: Terminology
    IEC 60688:2012 Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
    EN ISO 10523 : 2012 WATER QUALITY - DETERMINATION OF PH (ISO 10523:2008)
    EN 61000-4-7:2002/A1:2009 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO (IEC 61000-4-7:2002/A1:2008)
    ISO 6975:1997 Natural gas — Extended analysis — Gas-chromatographic method
    ISO 7935:1992 Stationary source emissions Determination of the mass concentration of sulfur dioxide Performance characteristics of automated measuring methods
    IEC 62052-11:2003+AMD1:2016 CSV Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 11: Metering equipment
    ISO 8217:2017 Petroleum products Fuels (class F) Specifications of marine fuels
    ASTM F 2602 : 2013-10 TEST METHOD FOR DETERMINING THE MOLAR MASS OF CHITOSAN AND CHITOSAN SALTS BY SIZE EXCLUSION CHROMATOGRAPHY WITH MULTI-ANGLE LIGHT SCATTERING DETECTION (SEC-MALS)
    ISO 6060:1989 Water quality — Determination of the chemical oxygen demand
    ISO 4677-1:1985 Atmospheres for conditioning and testing Determination of relative humidity Part 1: Aspirated psychrometer method
    ISO 16622:2002 Meteorology Sonic anemometers/thermometers Acceptance test methods for mean wind measurements
    ISO 11042-1:1996 Gas turbines — Exhaust gas emission — Part 1: Measurement and evaluation
    ISO 11042-2:1996 Gas turbines — Exhaust gas emission — Part 2: Automated emission monitoring
    EN 61672-1:2013 ELECTROACOUSTICS - SOUND LEVEL METERS - PART 1: SPECIFICATIONS (IEC 61672-1:2013)
    EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
    EN 50470-1:2006 Electricity metering equipment (a.c.) - Part 1: General requirements, tests and test conditions - Metering equipment (class indexes A, B and C)
    ISO 11541:1997 Natural gas Determination of water content at high pressure
    EN 62282-3-201:2017 Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
    EN ISO 6975 : 2005 NATURAL GAS - EXTENDED ANALYSIS - GAS-CHROMATOGRAPHIC METHOD
    IEC 61000-4-7:2002+AMD1:2008 CSV Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto
    IEC 62053-22:2003+AMD1:2016 CSV Electricity metering equipment (a.c.) - Particular Requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S)
    ISO 9000:2015 Quality management systems Fundamentals and vocabulary
    IEC 60359:2001 Electrical and electronic measurement equipment - Expression of performance
    ISO 5815-2:2003 Water quality Determination of biochemical oxygen demand after n days (BODn) Part 2: Method for undiluted samples
    ISO 5348:1998 Mechanical vibration and shock Mechanical mounting of accelerometers
    ISO 10849:1996 Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Performance characteristics of automated measuring systems
    ISO 10780:1994 Stationary source emissions — Measurement of velocity and volume flowrate of gas streams in ducts
    EN 61028:1993/A2:1997 ELECTRICAL MEASURING INSTRUMENTS - X-Y RECORDERS
    ISO 10523:2008 Water quality — Determination of pH
    ISO 10396:2007 Stationary source emissions — Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems
    IEC 61028:1990 Electrical measuring instruments - X-Y recorders
    ISO 4677-2:1985 Atmospheres for conditioning and testing Determination of relative humidity Part 2: Whirling psychrometer method
    EN 61000-4-13:2002/A2:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002/A2:2015)
    IEC 60050-300:2001 International Electrotechnical Vocabulary (IEV) - Part 300: Electrical and electronic measurements and measuring instruments - Part 311: General terms relating to measurements - Part 312: General terms relating to electrical measurements - Part 313: Types of electrical measuring instruments - Part 314: Specific terms according to the type of instrument
    IEC 62282-3-201:2017 Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems
    IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests
    ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
    ISO 11632:1998 Stationary source emissions — Determination of mass concentration of sulfur dioxide — Ion chromatography method
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective