Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 623-4:2004

    Current The latest, up-to-date edition.

    ADVANCED TECHNICAL CERAMICS - MONOLITHIC CERAMICS - GENERAL AND TEXTURAL PROPERTIES - PART 4: DETERMINATION OF SURFACE ROUGHNESS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2004

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principles of conventional surface texture measurement
      4.1 Surface texture parameters
      4.2 Trace manipulation
      4.3 Instrument calibration
    5 Factors affecting the determination of surface texture
      of ceramics
      5.1 Microstructural influences
      5.2 Special surface profiles
      5.3 Influences of form
      5.4 Instrumental influence
    6 Test procedure
      6.1 Machine set-up
      6.2 Test requirements
      6.3 Test piece measurement
    7 Test report
    Annex A (informative) Interlaboratory evaluation of ceramic
            surface texture test procedures
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the use of conventional stylus type instruments for the measurement of surface texture of advanced monolithic technical ceramics, sets the test machine measuring parameters and recommends the adoption of certain precautions and conditions of measurement.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. ENV 623-4 (12/2004)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 4287:1998/A1:2009 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - TERMS, DEFINITIONS AND SURFACE TEXTURE PARAMETERS
    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO 12179:2000 Geometrical Product Specifications (GPS) Surface texture: Profile method Calibration of contact (stylus) instruments
    EN ISO 13565-3 : 2000 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE - PROFILE METHOD - SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 3: HEIGHT CHARACTERIZATION USING THE MATERIAL PROBABILITY CURVE
    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    ISO 13565-3:1998 Geometrical Product Specifications (GPS) Surface texture: Profile method; Surfaces having stratified functional properties Part 3: Height characterization using the material probability curve
    EN ISO 4288 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - RULES AND PROCEDURES FOR THE ASSESSMENT OF SURFACE TEXTURE
    ENV 1006 : DRAFT 2003 ADVANCED TECHNICAL CERAMICS - MONOLITHIC CERAMICS - GUIDANCE ON THE SELECTION OF TEST PIECES FOR THE EVALUATION OF PROPERTIES
    EN ISO 12179:2000/AC:2008 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - CALIBRATION OF CONTACT (STYLUS) INSTRUMENTS
    EN ISO 11562:1997/AC:2008 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - METROLOGICAL CHARACTERISTICS OF PHASE CORRECT FILTERS
    EN 623-1:2006 Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 1: Determination of the presence of defects by dye penetration
    EN ISO 13565-2 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD; SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 2: HEIGHT CHARACTERIZATION USING THE LINEAR MATERIAL RATIO
    ISO 5436-2:2012 Geometrical product specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards
    EN ISO 5436-2:2012 Geometrical product specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2012)
    ISO 3274:1996 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
    ISO 5436-1:2000 Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 1: Material measures
    EN ISO 13565-1 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 1: FILTERING AND GENERAL MEASUREMENT CONDITIONS
    EN ISO 3274 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - NOMINAL CHARACTERISTICS OF CONTACT (STYLUS) INSTRUMENTS
    EN ISO 5436-1 : 2000 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD; MEASUREMENT STANDARDS - PART 1: MATERIAL MEASURES
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective