I.S. EN IEC 62561-2:2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES
Hardcopy , PDF
English
16-04-2018
12-10-2019
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Tests
6 Electromagnetic compatibility (EMC)
7 Structure and content of the test report
Annex A (normative) - Environmental test for conductors,
air-termination rods and earth lead-in rods
Annex B (normative) - Electrical test
Annex C (normative) - Requirements for conductors
Annex D (normative) - Requirements for earth electrodes
Annex E (normative) - Flow chart of tests for air-termination
conductors, air-termination rods, earth lead-in rods,
down-conductors, earth conductors and earth plates,
see Figure E.1
Annex F (normative) - Flow chart of tests for earth rods
Annex G (normative) - Flow chart of tests of couplers
for earth rods
Bibliography
Annex ZA (normative) - Normative references to
International publications with their
corresponding European publications
Defines the requirements and tests for: - metallic conductors (other than 'natural' conductors) that form part of the air-termination and down-conductor systems, - metallic earth electrodes that form part of the earth-termination system.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. Supersedes I.S. EN 62561-2. (04/2018)
|
| DocumentType |
Standard
|
| Pages |
0
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| IEC 62561-2:2012 | Identical |
| EN IEC 62561-2:2018 | Identical |
| EN 50164-2:2008 | Lightning Protection Components (LPC) - Part 2: Requirements for conductors and earth electrodes |
| EN 62305-4:2011/AC:2016 | PROTECTION AGAINST LIGHTNING - PART 4: ELECTRICAL AND ELECTRONIC SYSTEMS WITHIN STRUCTURES (IEC 62305-4:2010) |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| IEC 60468:1974 | Method of measurement of resistivity of metallic materials |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| IEC 62561-1:2017 | Lightning protection system components (LPSC) - Part 1: Requirements for connection components |
| IEC 62305-1:2010 | Protection against lightning - Part 1: General principles |
| EN ISO 6988:1994 | Metallic and other non-organic coatings - Sulfur dioxide test with general condensation of moisture (ISO 6988:1985) |
| EN 62305-3:2011 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic method |
| EN 62561-1:2017 | Lightning Protection System Components (LPSC) - Part 1: Requirements for connection components |
| IEC 62305-4:2010 | Protection against lightning - Part 4: Electrical and electronic systems within structures |
| ISO 1460:1992 | Metallic coatings — Hot dip galvanized coatings on ferrous materials — Gravimetric determination of the mass per unit area |
| ISO 6988:1985 | Metallic and other non organic coatings — Sulfur dioxide test with general condensation of moisture |
| IEC 60068-2-52:2017 | Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) |
| IEC 62305-3:2010 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| ISO 6957:1988 | Copper alloys — Ammonia test for stress corrosion resistance |
| EN ISO 2178:2016 | Non-magnetic coatings on magnetic substrates - Measurement of coating thickness - Magnetic method (ISO 2178:2016) |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.