I.S. EN ISO 11114-1:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 1: METALLIC MATERIALS (ISO 11114-1:2012)
Hardcopy , PDF
14-07-2020
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Compatibility criteria
6 Material compatibility
Annex A (informative) - Gas/materials NQSAB compatibility
code
Bibliography
Gives requirements for the selection of safe combinations of metallic cylinder and valve materials and cylinder gas content.
| DocumentType |
Standard
|
| Pages |
80
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 11114-1:2012 | Identical |
| SN EN ISO 11114-1 : 2012 | Identical |
| NS EN ISO 11114-1 : 2012 AMD 1 2017 | Identical |
| DIN EN ISO 11114-1:2012-07 | Identical |
| NBN EN ISO 11114-1 : 2012 | Identical |
| NF EN ISO 11114-1 : 2012 AMD 1 2017 | Identical |
| UNE-EN ISO 11114-1:2012 | Identical |
| UNI EN ISO 11114-1 : 2012 | Identical |
| NEN EN ISO 11114-1 : 2012 AMD 1 2017 | Identical |
| BS EN ISO 11114-1 : 2012 | Identical |
| ONORM EN ISO 11114-1 : OCT 2017 | Identical |
| ISO 9809-3:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 3: Normalized steel cylinders |
| ISO 15510:2014 | Stainless steels — Chemical composition |
| ISO 11118:2015 | Gas cylinders — Non-refillable metallic gas cylinders — Specification and test methods |
| ISO 9809-4:2014 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa |
| ISO 11114-3:2010 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 3: Autogenous ignition test for non-metallic materials in oxygen atmosphere |
| ISO 4706:2008 | Gas cylinders — Refillable welded steel cylinders — Test pressure 60 bar and below |
| ISO 7866:2012 | Gas cylinders — Refillable seamless aluminium alloy gas cylinders — Design, construction and testing |
| ISO 9328-5:2011 | Steel flat products for pressure purposes Technical delivery conditions Part 5: Weldable fine grain steels, thermomechanically rolled |
| ISO 10297:2014 | Gas cylinders — Cylinder valves — Specification and type testing |
| ISO 6361-2:2014 | Wrought aluminium and aluminium alloys Sheets, strips and plates Part 2: Mechanical properties |
| ISO 11114-2:2013 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials |
| ISO 11120:2015 | Gas cylinders Refillable seamless steel tubes of water capacity between 150 l and 3000 l Design, construction and testing |
| ISO 10156:2017 | Gas cylinders — Gases and gas mixtures — Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets |
| ISO 9809-2:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa |
| ISO 9809-1:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa |
| ISO 11439:2013 | Gas cylinders — High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.