Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 13856-2:2013

    Current The latest, up-to-date edition.

    SAFETY OF MACHINERY - PRESSURE-SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR DESIGN AND TESTING OF PRESSURE-SENSITIVE EDGES AND PRESSURE-SENSITIVE BARS (ISO 13856-2:2013)

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Requirements for design and testing
    5 Marking
    6 Information for selection and use
    7 Verification of requirements
    Annex A (normative) - Timing diagrams for pressure
            -sensitive edges/bars with/without reset
    Annex B (informative) - Operating speed, force and
            travel - Explanatory remarks and
            recommendations
    Annex C (informative) - Device selection guidance
            for machinery manufacturer/user
    Annex D (informative) - Design guidance
    Annex E (informative) - Application guidance
    Annex F (informative) - Guidance on commissioning
            and testing after installation
    Annex G (informative) - General considerations for
            systems meeting ISO 13849-1, category 2
    Bibliography
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential Requirements
             of EU Directive 2006/42/EC

    Abstract - (Show below) - (Hide below)

    Sets up general principles and specifies requirements for the design testing of pressure-sensitive edges and pressure-sensitive bars used as safeguards and not as actuating devices for normal operation.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 1760-2. (04/2013)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 14119:2013 Safety of machinery Interlocking devices associated with guards Principles for design and selection
    IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    ISO 14120:2015 Safety of machinery Guards General requirements for the design and construction of fixed and movable guards
    ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
    ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
    IEC 61000-4-6 : 4.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 61496-3:2008 Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
    IEC 61000-4-2:2008 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
    IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
    ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation
    IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
    ISO 4414:2010 Pneumatic fluid power General rules and safety requirements for systems and their components
    IEC 61439-1:2011 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
    IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
    ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
    IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    IEC 61496-2:2013 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective