• Shopping Cart
    There are no items in your cart

I.S. EN ISO 14373:2015

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

RESISTANCE WELDING - PROCEDURE FOR SPOT WELDING OF UNCOATED AND COATED LOW CARBON STEELS (ISO 14373:2015)

Available format(s)

Hardcopy , PDF

Superseded date

08-02-2024

Superseded by

I.S. EN ISO 14373:2024

Language(s)

English

Published date

01-01-2015

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.


Dates of withdrawal of national standards are available from NSAI.

€37.00
Excluding VAT

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Materials
6 Surface conditions
7 Edge conditions, form of component, and weld spacing
8 Electrodes
9 Weld assessment
10 Weld quality requirements
11 Multi-weld arrays
Annex A (informative) - Recommendations for spot welding
        equipment
Annex B (informative) - Typical spot welding conditions
Annex C (informative) - Partial list of steel types applicable to this
        International Standard
Bibliography

Defines requirements for resistance spot welding in the fabrication of assemblies of uncoated and metallic coated low carbon steel, comprising two or three sheets of metal, where the maximum single sheet thickness of components to be welded is within the range 0,4 mm to 3 mm, for the following materials: - uncoated steels; - hot-dip zinc or iron-zinc alloy (galvannealed) coated steel; - electrolytic zinc, zinc-iron, or zinc-nickel coated steel; - aluminium coated steel; - zinc-aluminium coated steel.

DocumentType
Standard
Pages
30
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

ISO 5182:2016 Resistance welding Materials for electrodes and ancillary equipment
ISO 14270:2016 Resistance welding Destructive testing of welds Specimen dimensions and procedure for mechanized peel testing resistance spot, seam and embossed projection welds
ISO 10447:2015 Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds
ISO 5830:1984 Resistance spot welding Male electrode caps
ISO 3574:2012 Cold-reduced carbon steel sheet of commercial and drawing qualities
ISO 3573:2012 Hot-rolled carbon steel sheet of commercial and drawing qualities
ISO 9364:2011 Continuous hot-dip 55 % aluminium/zinc alloy-coated steel sheet of commercial, drawing and structural qualities
ISO 4998:2014 Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of structural quality
ISO 5002:2013 Hot-rolled and cold-reduced electrolytic zinc-coated carbon steel sheet of commercial and drawing qualities
ISO 15614-12:2014 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 12: Spot, seam and projection welding
ISO 669:2016 Resistance welding Resistance welding equipment Mechanical and electrical requirements
ISO 14329:2003 Resistance welding Destructive tests of welds Failure types and geometric measurements for resistance spot, seam and projection welds
ISO 15609-5:2011 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5: Resistance welding
ISO 3575:2016 Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of commercial and drawing qualities
ISO 4950-2:1995 High yield strength flat steel products — Part 2: Products supplied in the normalized or controlled rolled condition
ISO 4950-1:1995 High yield strength flat steel products — Part 1: General requirements
ISO 5000:2011 Continuous hot-dip aluminium-silicon-coated cold-reduced carbon steel sheet of commercial and drawing qualities
ISO 5184:1979 Straight resistance spot welding electrodes
ISO 17677-1:2009 Resistance welding Vocabulary Part 1: Spot, projection and seam welding
ISO 18278-1:2015 Resistance welding Weldability Part 1: General requirements for the evaluation of weldability for resistance spot, seam and projection welding of metallic materials
ISO 5821:2009 Resistance welding — Spot welding electrode caps

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.