Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN ISO 1452-4:2009

    Current The latest, up-to-date edition.

    LASTICS PIPING SYSTEMS FOR WATER SUPPLY AND FOR BURIED AND ABOVE-GROUND DRAINAGE AND SEWERAGE UNDER PRESSURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 4: VALVES

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2009

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions, symbols and abbreviated terms
    4 Material
    5 General characteristics
    6 Geometrical characteristics
    7 Classification and operating conditions
    8 Mechanical characteristics
    9 Physical characteristics
    10 Chemical characteristics
    11 Sealing rings
    12 Adhesives
    13 Performance requirements
    14 Marking
    Annex A (normative) - Imperial(inch)-sized valves
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC-U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 1456-1 and I.S. EN 1452-4. (01/2010) Supersedes I.S. 123. (08/2016)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 16135:2006 Industrial valves Ball valves of thermoplastics materials
    ISO 580:2005 Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating
    ISO 2507-2:1995 Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes
    ISO 2507-1:1995 Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method
    ISO 1452-1:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 1: General
    ISO 1452-3:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 3: Fittings
    ISO 1452-5:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 5: Fitness for purpose of the system
    ENV 1452-7:2000 Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity
    CEN/TR 15438:2007 Plastics piping systems - Guidance for coding of products and their intended uses
    EN 802:1994 Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 8659:1989 Thermoplastics valves Fatigue strength Test method
    ISO 1452-2:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 2: Pipes
    ISO 1167-3:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 16138:2006 Industrial valves Diaphragm valves of thermoplastics materials
    ISO 16137:2006 Industrial valves Check valves of thermoplastics materials
    ISO 16136:2006 Industrial valves Butterfly valves of thermoplastics materials
    ISO/TR 4191:2014 Plastics piping systems for water supply Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) Guidance for installation
    ISO 16139:2006 Industrial valves Gate valves of thermoplastics materials
    ISO 21787:2006 Industrial valves Globe valves of thermoplastics materials
    ISO 7686:2005 Plastics pipes and fittings — Determination of opacity
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective