I.S. EN ISO 15876-3:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTENE (PB) - PART 3: FITTINGS (ISO 15876-3:2017)
Hardcopy , PDF
02-02-2021
English
01-01-2017
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material characteristics
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics of plastics fittings
8 Melt flow rate
9 Sealing elements
10 Performance requirements
11 Marking
Bibliography
Describes the characteristics of fittings for polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application.
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 15876-3:2017 | Identical |
| NEN EN ISO 15876-3 : 2017 | Identical |
| BS EN ISO 15876-3:2017 | Identical |
| UNI EN ISO 15876-3 : 2005 | Identical |
| NS EN ISO 15876-3 : 2017 | Identical |
| SN EN ISO 15876-3:2017 | Identical |
| UNE-EN ISO 15876-3:2017 | Identical |
| NBN EN ISO 15876-3 : 2004 | Identical |
| EN ISO 15876-3:2017 | Identical |
| DIN EN ISO 15876-3:2015-08 (Draft) | Identical |
| NF EN ISO 15876-3 : 2017 | Identical |
| ONORM EN ISO 15876-3 : 2018 | Identical |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity |
| ISO 15876-1:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| EN 1254-6:2012 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| CEN/TR 12108:2012 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 15876-5:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| EN 1254-8:2012 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.