I.S. EN ISO 15877-3:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 3: FITTINGS
Hardcopy , PDF
03-11-2021
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
3.1 Terms and definitions
3.2 Symbols
4 Material characteristics
4.1 General
4.2 Fitting material
4.3 Evaluation of sigma[LPL]-values
4.4 Thermal stability
4.5 Metallic material
4.6 Influence on water intended for human consumption
5 General characteristics
5.1 Appearance
5.2 Opacity
6 Geometrical
6.1 General
6.2 Dimensions of fittings
6.3 Dimensions of sockets
6.4 Dimensions of flange adaptors and flanges
6.5 Dimensions of metallic fittings
7 Mechanical characteristics
7.1 Resistance to internal pressure
7.2 Determination of free lengths
7.3 Derivation of the hydrostatic test pressure
8 Performance requirements
9 Adhesives
10 Sealing rings
11 Marking
11.1 General
11.2 Minimum required marking
11.3 Additional marking
Bibliography
Describes the characteristics of fittings made from chlorinated poly(vinyl chloride) (PVCC) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application.
| DocumentType |
Standard
|
| Pages |
48
|
| ProductNote |
This standard is identical to EN ISO 15877-3 : 2009
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN ISO 15877-3 : 2009 AMD 1 2010 | Identical |
| SN EN ISO 15877-3 : 2009 AMD 1 2011 | Identical |
| ISO 15877-3:2009 | Identical |
| DIN EN ISO 15877-3:2011-03 | Identical |
| ONORM EN ISO 15877-3 : 2011 | Identical |
| NEN EN ISO 15877-3 : 2009 AMD 1 2010 | Identical |
| NBN EN ISO 15877-3 : 2009 AMD 1 2010 | Identical |
| UNI EN ISO 15877-3 : 2011 | Identical |
| UNE-EN ISO 15877-3:2009 | Identical |
| NF EN ISO 15877-3 : 2009 AMD 1 2011 | Identical |
| BS EN ISO 15877-3 : 2009 | Identical |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 727-2:2005 | Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure — Part 2: Inch-based series |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 15877-2:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 2: Pipes |
| ISO 15877-1:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 1: General |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 15877-5:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 5: Fitness for purpose of the system |
| ISO 2536:1974 | Unplasticized polyvinyl chloride (PVC) pressure pipes and fittings, metric series Dimensions of flanges |
| ENV 12108:2001 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO/TS 15877-7:2009 | Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 7: Guidance for the assessment of conformity |
| EN 727:1994 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 727-1:2002 | Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure — Part 1: Metric series |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.