I.S. EN ISO 16101:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING
Hardcopy , PDF
English
01-01-2004
19-09-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test requirements
5 Selection and preparation of test packagings
6 Facilities for testing
7 Conditioning procedures
8 Permeability testing
Annex A (normative) Standard liquids and applicability to
polyethylene types
Annex B (normative) Small scale laboratory tests to assess
packaged substances against standard liquids
Annex C (informative) Assimilation of packaged substance to
standard liquids
Bibliography
Describes the requirements and test methods for compatibility testing of polyethylene based plastics packagings and composite packagings with plastic inners containing liquids.
| DocumentType |
Standard
|
| Pages |
148
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NEN EN ISO 16101 : 2004 | Identical |
| EN ISO 16101:2004 | Identical |
| BS EN ISO 16101:2004 | Identical |
| NF EN ISO 16101 : 2005 | Identical |
| DIN EN ISO 16101:2004-12 | Identical |
| ISO 16101:2004 | Identical |
| NS EN ISO 16101 : 1ED 2004 | Identical |
| NBN EN ISO 16101 : 2004 | Identical |
| UNE-EN ISO 16101:2005 | Identical |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 11542-2:1998 | Plastics — Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| EN ISO 16104:2003 | Packaging - Transport packaging for dangerous goods - Test methods (ISO 16104:2003) |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| ISO 16770:2004 | Plastics — Determination of environmental stress cracking (ESC) of polyethylene — Full-notch creep test (FNCT) |
| EN ISO 11403-3:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| EN ISO 2818:1996 | Plastics - Preparation of test specimens by machining (ISO 2818:1994) |
| ISO 1628-3:2010 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 3: Polyethylenes and polypropylenes |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 16104:2003 | Packaging — Transport packaging for dangerous goods — Test methods |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1872-2:2007 | Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
| EN ISO 6252 : 1997 | PLASTICS - DETERMINATION OF ENVIRONMENTAL STRESS CRACKING (ESC) - CONSTANT-TENSILE-STRESS METHOD |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| EN ISO 1872-2:2007 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:2007) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN ISO 1628-3:2010 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes (ISO 1628-3:2010) |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 6252:1992 | Plastics — Determination of environmental stress cracking (ESC) — Constant-tensile-stress method |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.