I.S. EN ISO 6185-4:2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER (ISO 6185-4:2011, CORRECTED VERSION 2014-08-01)
Hardcopy , PDF
English
01-01-2011
07-02-2019
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Materials
6 Functional components
7 Safety requirements of the completed boat
8 Builder's plate(s)
9 Owner's manual
10 Standard equipment
Annex A (informative) - Typical Type IX powered boat
Annex B (informative) - Typical Type X powered boat
Bibliography
Annex ZA (informative) - Relationship between this
International Standard and the Essential
Requirements of EU Directive 94/25/EC as
amended by Directive 2003/44/EC
Describes the minimum safety characteristics required for the design, materials, manufacture and testing of rigid inflatable boats (RIBs) with a hull length of between 8 m and 24 m and with a motor power rating of 15 kW and greater.
| DocumentType |
Standard
|
| Pages |
46
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 6185-4:2011 | Identical |
| ISO 6185-4:2011 | Identical |
| EN ISO 6185-4:2018 | Identical |
| ISO 10239:2014 | Small craft — Liquefied petroleum gas (LPG) systems |
| ISO 12215-5:2008 | Small craft — Hull construction and scantlings — Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| ISO 7010:2011 | Graphical symbols — Safety colours and safety signs — Registered safety signs |
| ISO 14946:2001 | Small craft — Maximum load capacity |
| ISO 4675:2017 | Rubber- or plastics-coated fabrics — Low-temperature bend test |
| ISO 11591:2011 | Small craft, engine-driven — Field of vision from helm position |
| ISO 12217-3:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m |
| ISO 10088:2013 | Small craft — Permanently installed fuel systems |
| ISO 2411:2017 | Rubber- or plastics-coated fabrics — Determination of coating adhesion |
| ISO 11105:1997 | Small craft — Ventilation of petrol engine and/or petrol tank compartments |
| ISO 8666:2016 | Small craft — Principal data |
| ISO 8847:2004 | Small craft — Steering gear — Cable and pulley systems |
| ISO 15084:2003 | Small craft — Anchoring, mooring and towing — Strong points |
| ISO 6185-3:2014 | Inflatable boats — Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater |
| ISO 10133:2012 | Small craft — Electrical systems — Extra-low-voltage d.c. installations |
| ISO 12217-1:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m |
| ISO 12215-3:2002 | Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| ISO 8848:1990 | Small craft — Remote steering systems |
| ISO 10592:1994 | Small craft — Hydraulic steering systems |
| ISO 11812:2001 | Small craft — Watertight cockpits and quick-draining cockpits |
| ISO 10240:2004 | Small craft — Owner's manual |
| ISO 21487:2012 | Small craft — Permanently installed petrol and diesel fuel tanks |
| ISO 13297:2014 | Small craft — Electrical systems — Alternating current installations |
| ISO 15085:2003 | Small craft — Man-overboard prevention and recovery |
| ISO 12216:2002 | Small craft — Windows, portlights, hatches, deadlights and doors — Strength and watertightness requirements |
| ISO 3011:1997 | Rubber- or plastics-coated fabrics — Determination of resistance to ozone cracking under static conditions |
| ISO 4674-1:2016 | Rubber- or plastics-coated fabrics — Determination of tear resistance — Part 1: Constant rate of tear methods |
| ISO 10087:2006 | Small craft — Craft identification — Coding system |
| ISO 12215-6:2008 | Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |
| ISO 14945:2004 | Small craft — Builder's plate |
| ISO 8099:2000 | Small craft — Toilet waste retention systems |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.