I.S. EN ISO 6892-1:2019
Current
The latest, up-to-date edition.
Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2019)
Hardcopy , PDF
English
23-12-2019
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Principle
6 Test pieces
7 Determination of original cross-sectional area
8 Original gauge length and extensometer gauge length
9 Accuracy of testing apparatus
10 Conditions of testing
11 Determination of the upper yield strength
12 Determination of the lower yield strength
13 Determination of proof strength, plastic extension
14 Determination of proof strength, total extension
15 Method of verification of permanent set strength
16 Determination of the percentage yield point extension
17 Determination of the percentage plastic extension at maximum force
18 Determination of the percentage total extension at maximum force
19 Determination of the percentage total extension at fracture
20 Determination of percentage elongation after fracture
21 Determination of percentage reduction of area
22 Test report
23 Measurement uncertainty
Annex A (informative) Recommendations concerning the use of computer-controlled tensile testing machines
Annex B (normative) Types of test pieces to be used for thin products: sheets, strips, and flats between 0,1 mm and 3 mm thick
Annex C (normative) Types of test pieces to be used for wire, bars, and sections with a diameter or thickness of less than 4 mm
Annex D (normative) Types of test pieces to be used for sheets and flats of thickness equal to or greater than 3 mm and wire, bars, and sections of diameter or thickness equal to or greater than 4 mm
Annex E (normative) Types of test pieces to be used for tubes
Annex F (informative) Estimation of the crosshead separation rate in consideration of the stiffness (or compliance) of the testing equipment
Annex G (normative) Determination of the modulus of elasticity of metallic materials using a uniaxial tensile test
Annex H (informative) Measuring the percentage elongation after fracture if the specified value is less than 5 %
Annex I (informative) Measurement of percentage elongation after fracture based on subdivision of the original gauge length
Annex J (informative) Determination of the percentage plastic elongation without necking, Awn, for long products such as bars, wire, and rods
Annex K (informative) Estimation of the uncertainty of measurement
Annex L (informative) Precision of tensile testing — Results from interlaboratory programmes
Bibliography
This document specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
| Committee |
ISO/TC 164
|
| DocumentType |
Test Method
|
| Pages |
96
|
| ProductNote |
NOTE: The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. THIS STANDARD ALSO REFERS TO CWA 15261-2:2005,IACS W2,NIS 80:1994,NIS 3003:1995
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN ISO 6892-1:2019 | Identical |
| ISO 6892-1:2019 | Identical |
| JIS Z 2241:2011 | Metallic materials -- Tensile testing -- Method of test at room temperature |
| ISO 3183:2019 | Petroleum and natural gas industries — Steel pipe for pipeline transportation systems |
| ISO 2566-2:1984 | Steel — Conversion of elongation values — Part 2: Austenitic steels |
| ISO/TR 25679:2005 | Mechanical testing of metals — Symbols and definitions in published standards |
| ISO 2566-1:1984 | Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ASTM A 370 : 2019 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 11960:2014 | Petroleum and natural gas industries — Steel pipes for use as casing or tubing for wells |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.