IEC 60034-1:2017

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

Rotating electrical machines - Part 1: Rating and performance

Available format(s): Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

Superseded date: 14-02-2022

Language(s): English - French

Published date: 09-05-2017

Publisher: International Electrotechnical Committee

Table of Contents - (Show below) - (Hide below)

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Duty
5 Rating
6 Site conditions
7 Electrical operating conditions
8 Thermal performance and tests
9 Other performance and tests
10 Rating plates
11 Miscellaneous requirements
12 Tolerances
13 Electromagnetic compatibility (EMC)
14 Safety
Annex A (informative) - Guidance for the application
        of duty type S10 and for establishing the value of
        relative thermal life expectancy TL
Annex B (informative) - Electromagnetic compatibility
        (EMC) limits
Bibliography

Abstract - (Show below) - (Hide below)

IEC 60034-1:2017 is now available as IEC 60034-1:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 60034-1:2017 is applicable to all rotating electrical machines except those covered by other IEC standards, for example, IEC 60349. Machines within the scope of this document may also be subject to superseding, modifying or additional requirements in other standards, for example, IEC 60079 and IEC 60092. This new edition contains a number of clarifications, corrections and enhancements with regard to the previous edition.

General Product Information - (Show below) - (Hide below)

Committee	TC 2
Development Note	Stability Date: 2020. (05/2017)
Document Type	Standard
ISBN
Pages
Published
Publisher	International Electrotechnical Committee
Status	Superseded
Superseded By	IEC 60034-1:2022 IEC 60034-1:2022 RLV
Supersedes	IEC 60034-1:2010

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
IS 15999 : Part 1 : 2021	Identical
I.S. EN 60034-1:2010	Identical
NEN EN IEC 60034-1 : 2010 C11 2010	Identical
CEI 2-3 : 1988 COR 1992	Identical
DIN EN 60034-1 : 2011	Identical
BIS IS 15999-1 : 2016	Identical
SN EN 60034-1 : 2010	Identical
UNE 20113-1:1995	Identical
CEI 2-3 V1 : 1992	Identical
NBN EN 60034-1 : 2011	Identical
GOST IEC 60034-1 : 2014	Identical
UNE-EN 60034-1:2011	Identical
VDE 0530-1 : 2011	Identical
SANS 60034-1 : 4ED 2010	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

DD IEC TS 60034-20-1 : 2002 AMD 16729	ROTATING ELECTRICAL MACHINES - CONTROL MOTORS - STEPPING MOTORS
BS 7698-4(1993) : 1993	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - SPECIFICATION FOR CONTROLGEAR AND SWITCHGEAR
15/30265353 DC : 0	BS EN 62271-1 ED 2 - HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS FOR ALTERNATING CURRENT SWITCHGEAR AND CONTROLGEAR
BS IEC TS 60034-18.34 : 2000 AMD 16621	ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
ISO 21873-1:2015	Building construction machinery and equipment Mobile crushers Part 1: Terminology and commercial specifications
DIN EN 14161:2015-07	ABSCHLUESSE AUSSEN UND AUSSENJALOUSIEN - LEISTUNGS- UND SICHERHEITSANFORDERUNGEN
BIS IS/IEC 60947-4-2 : 1999	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4: CONTRACTORS AND MOTOR-STARTERS - SECTION 2: AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
NBR IEC 60034-14 : 2011	ROTATING ELECTRICAL MACHINES - PART 14: MEASUREMENT, EVALUATION AND LIMITS OF THE MECHANICAL VIBRATION SEVERITY OF MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER
DIN EN 61800-9-2 : 2018-01	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017)
13/30288508 DC : 0	BS IEC 60034-27-3 ED 1.0 - ROTATING ELECTRICAL MACHINES - PART 27-3: DIELECTRIC DISSIPATION FACTOR MEASUREMENT ON STATOR WINDING INSULATION OF ROTATING ELECTRICAL MACHINES
CEI EN 60034-28 : 2014	ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS
CEI EN 60349-4 : 2014	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
BS PD ISO/TS 19466 : 2017	ELECTRICALLY PROPELLED MOPEDS AND MOTORCYCLES - TEST METHOD FOR EVALUATING PERFORMANCE OF REGENERATIVE BRAKING SYSTEMS
BS EN 60947-4-1 : 2010	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
13/30268505 DC : 0	BS ISO 21873-1 - BUILDING CONSTRUCTION MACHINERY AND EQUIPMENT - MOBILE CRUSHERS - PART 1: TERMINOLOGY AND COMMERCIAL SPECIFICATIONS
GOST R ISO 8528-3 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
DIN EN ISO 13350:2016-02	FANS - PERFORMANCE TESTING OF JET FANS (ISO 13350:2015)
DIN ISO 8528-5:1997-11	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
I.S. EN 60079-0:2012	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD))
15/30324519 DC : 0	BS EN ISO 14224 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT
DIN EN ISO 5802:2016-02	INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU (ISO 5802:2001 + AMD 1:2015)
BS EN 61800-9-2:2017 (published 2017-12)	Adjustable speed electrical power drive systems Ecodesign for power drive systems, motor starters, power electronics and their driven applications. Energy efficiency indicators for power drive systems and motor starters
04/30115708 DC : DRAFT JUL 2004	IEC TS 60034-17 - ROTATING ELECTRICAL MACHINES - PART 17: CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE
BS IEC 60079-19 : 1993	ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - REPAIR AND OVERHAUL FOR APPARATUS USED IN EXPLOSIVE ATMOSPHERES (OTHER THAN MINES OR EXPLOSIVES)
BS ISO 8528-4 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
02/206929 DC : DRAFT JUN 2002	IEC 60034-25. ED.1 - ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS FOR CONVERTER SUPPLY
BS IEC 60034-17 : 1998	ROTATING ELECTRICAL MACHINES - CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE
I.S. EN 60034-18-31:2012	ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012 (EQV))
BS 7698-1(1993) : 1993	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - SPECIFICATION FOR APPLICATION, RATINGS AND PERFORMANCE
I.S. EN 60204-11:2000	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
NF ISO 8528-3 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
BS EN 60034-30 : 2009	ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS (IE-CODE)
DEFSTAN 02-607/3(2013) : 2013	DESIGN OF HIGH VOLTAGE ELECTRICAL POWER SYSTEMS FOR HM SHIPS, SUBMARINES AND THE ROYAL FLEET AUXILIARY
I.S. EN 1151-1:2006	PUMPS - ROTODYNAMIC PUMPS - CIRCULATION PUMPS HAVING A RATED POWER INPUT NOT EXCEEDING 200 W FOR HEATING INSTALLATIONS AND DOMESTIC HOT WATER INSTALLATIONS - PART 1: NON-AUTOMATIC CIRCULATION PUMPS, REQUIREMENTS, TESTING, MARKING
BS ISO 50004:2014	Energy management systems. Guidance for the implementation, maintenance and improvement of an energy management system
DD CLC/TS 60034-18-34 : 2004	ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
BS IEC 60092-301 : 1980	ELECTRICAL INSTALLATION IN SHIPS - EQUIPMENT - GENERATORS AND MOTORS
17/30358367 DC : 0	BS EN 17128 - NON-APPROVED LIGHT MOTORIZED VEHICLES FOR THE TRANSPORTATION OF PERSONS AND GOODS AND RELATED FACILITIES - PERSONAL LIGHT ELECTRIC VEHICLES (PLEV) - SAFETY REQUIREMENTS AND TEST METHODS
I.S. EN 60034-30-1:2014	ROTATING ELECTRICAL MACHINES - PART 30-1: EFFICIENCY CLASSES OF LINE OPERATED AC MOTORS (IE CODE)
BS EN 61400-22:2011	WIND TURBINES - PART 22: CONFORMITY TESTING AND CERTIFICATION
UNE-EN 60079-15:2013	Explosive atmospheres -- Part 15: Equipment protection by type of protection "n"
BS EN 88528-11:2004	Reciprocating internal combustion engine driven alternating current generating sets Rotary uninterruptible power systems. Performance requirements and test methods
BS ISO 8528-8:2016	Reciprocating internal combustion engine driven alternating current generating sets Requirements and tests for low-power generating sets
BS EN 60947-6-2 : 2003	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 6-2: MULTIPLE FUNCTION EQUIPMENT - CONTROL AND PROTECTIVE SWITCHING DEVICES (OR EQUIPMENT) (CPS)
CEI EN 60034-30-1 : 2015	ROTATING ELECTRICAL MACHINES - PART 30-1: EFFICIENCY CLASSES OF LINE OPERATED AC MOTORS (IE CODE)
BS EN 60947-4-2 : 2012	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
12/30269388 DC : 0	BS EN 328 - HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
CEI EN 60027-4 : 2008	LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 4: ROTATING ELECTRICAL MACHINES
07/30168628 DC : 0	BS EN 60079-15 - EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
SANS 60034-26 : 2ED 2006(R2011)	ROTATING ELECTRICAL MACHINES - PART 26: EFFECTS OF UNBALANCED VOLTAGES ON THE PERFORMANCE OF THREE-PHASE CAGE INDUCTION MOTORS
EN 15714-2 : 2009	INDUSTRIAL VALVES - ACTUATORS - PART 2: ELECTRIC ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
BS EN 60034-2-1:2014 (published 2014-09)	Rotating electrical machines Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)
15/30314548 DC : 0	BS EN 61800-9-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
VDI/VDE 3680:2002-10	CONTROL OF SYNCHRONOUS MACHINES
UNI EN 12693 : 2008	REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
09/30182105 DC : 0	BS EN 60349-2 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
PD IEC/TR 62001-1:2016 (published 2016-05)	High-voltage direct current (HVDC) systems. Guidance to the specification and design evaluation of AC filters Overview
12/30269385 DC : 0	BS EN 327 - HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS - TEST PROCEDURES FOR ESTABLISHING PERFORMANCE
BS EN 60349-2 : 2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
BS EN 60034-18-31 : 2012	ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES
BIS IS/ISO 8528-12 : 1997(R2014)	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 12: EMERGENCY POWER SUPPLY TO SAFETY SERVICES
UNI ISO 13380 : 2010	CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES ON USING PERFORMANCE PARAMETERS
NBR 10840 : 1989	MAQUINAS ELETRICAS GIRANTES - TURBOMAQUINAS SINCRONAS
NF EN 61116 : 2003	ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS
ISO 5801:2017	Fans — Performance testing using standardized airways
04/19993045 DC : 0	EN 14492-1 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
DEFSTAN 02-607/2(2008) : 2008	DESIGN OF HIGH VOLTAGE ELECTRICAL POWER SYSTEMS FOR HM SHIPS, SUBMARINES AND THE ROYAL FLEET AUXILIARY
BS EN 50598-2 : 2014	ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
DIN ISO 8528-3:1997-11	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
BIS IS/IEC 60079-1 : 2007	EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
CSA C22.3 No. 61936-1 : 2008 : R2015	POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
BS ISO 21927-3 : 2006	SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT EXHAUST VENTILATORS
BS EN 50216-12 : 2011	POWER TRANSFORMER AND REACTOR FITTINGS - PART 12: FANS
15/30314544 DC : 0	BS EN 61800-9-1 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ENERGY EFFICIENCY OF POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM)
EN 61800-9-1 : 2017	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM) (IEC 61800-9-1:2017)
PREN 1175 : DRAFT 2017	SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL/ELECTRONIC REQUIREMENTS
01/202922 DC : DRAFT APR 2001	IEC 60034-23 ED.1 - ROTATING ELECTRICAL MACHINES - PART 23: SPECIFICATION FOR THE REFURBISHING OF ROTATING ELECTRICAL MACHINES
BS 7698-3(1993) : 1993	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - SPECIFICATION FOR ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
BS ISO 21873-1 : 2015	BUILDING CONSTRUCTION MACHINERY AND EQUIPMENT - MOBILE CRUSHERS - PART 1: TERMINOLOGY AND COMMERCIAL SPECIFICATIONS
06/30148073 DC : DRAFT MAR 2006	IEC 61400-21 - WIND TURBINES - PART 21: MEASUREMENT AND ASSESSMENT OF POWER QUALITY CHARACTERISTICS OF GRID CONNECTED WIND TURBINES
04/30113660 DC : DRAFT MAY 2004	IEC 60079-7 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 7: INCREASED SAFETY 'E'
BS EN 60034-19 : 2014	ROTATING ELECTRICAL MACHINES - PART 19: SPECIFIC TEST METHODS FOR D.C. MACHINES ON CONVENTIONAL AND RECTIFIER-FED SUPPLIES
DD IEC TS 60034-17 : 2006	ROTATING ELECTRICAL MACHINES - PART 17: CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE
BS IEC 61892-3:2012	MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 3: EQUIPMENT
I.S. EN 60349-1:2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTOR-FED ALTERNATING CURRENT MOTORS
NBR ISO 8528-5 : 2014	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
05/30138880 DC : DRAFT SEP 2005	IEC 61986 ED 2 - ROTATING ELECTRICAL EQUIPMENT - EQUIVALENT LOADING AND SUPER-POSITIONING TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
BS EN 60034-28 : 2013	ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS
12/30248232 DC : DRAFT AUG 2012	BS EN 61400-2 - WIND TURBINES - PART 2: SMALL WIND TURBINES
BS EN 60034-18-21 : 2013	ROTATING ELECTRICAL MACHINES - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION
BS EN 60349-4 : 2013	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
BS EN 61986 : 2002	ROTATING ELECTRICAL MACHINES - EQUIVALENT LOADING AND SUPER-POSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
09/30209334 DC : 0	BS EN 60034-2-3 - ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC MOTORS
I.S. EN 61800-9-2:2017	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
CEI EN 60034-18-32 : 2011	ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF ELECTRICAL ENDURANCE
06/30153363 DC : DRAFT JULY 2006	BS IEC 60079-31 - EXPLOSIVE ATMOSPHERES - PART 31 - EQUIPMENT - PROTECTION BY ENCLOSURE "TD"
BS EN 60034-22:2009 (published 2010-02)	Rotating electrical machines AC generators for reciprocating internal combustion (RIC) engine driven generating sets
IEC 60204-1:2016	Safety of machinery - Electrical equipment of machines - Part 1: General requirements
03/316174 DC : DRAFT SEP 2003	ISO 8528-5 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
BS PD IEC TS 60034-2-3 : 2013	ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC INDUCTION MOTORS
17/30363845 DC : 0	BS ISO 21927-3 - SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT EXHAUST VENTILATORS
PREN 328 : DRAFT 2012	HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
ISO 3977-8:2002	Gas turbines Procurement Part 8: Inspection, testing, installation and commissioning
08/30176383 DC : DRAFT JAN 2008	BS EN 60034-18-1 - ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
01/202454 DC : DRAFT APRIL 2001	IEC 60034-14 ED.4 - ROTATING ELECTRICAL MACHINERY - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY
08/30191891 DC : DRAFT OCT 2008	BS EN 61936-1 - POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
CEI 301-1 : 1997	ELECTRIC DRIVES - DICTIONARY
03/316173 DC : DRAFT SEP 2003	ISO 8528-4 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
EN IEC 61058-1 : 2018	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS (IEC 61058-1:2016)
NBR ISO 8528-4 : 2014	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
S.R. CLC/TS 60034-25:2008	ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
BS EN 60034-11 : 2004	ROTATING ELECTRICAL MACHINES - PART 11: THERMAL PROTECTION
BIS IS/ISO 8528-3 : 2005(R2014)	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
BS 7698-5(1993) : 1993	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - SPECIFICATION FOR GENERATING SETS
BS 848-3(2001) : 2001	FANS FOR GENERAL PURPOSE - PART 3: PERFORMANCE TESTING IN SITU
ISO 13707:2000	Petroleum and natural gas industries Reciprocating compressors
BS 7698-12(1998) : 1998	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - EMERGENCY POWER SUPPLY TO SAFETY DEVICES
BS EN 60034-29 : 2008	ROTATING ELECTRICAL MACHINES - PART 29: EQUIVALENT LOADING AND SUPERPOSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
08/30184920 DC : DRAFT JULY 2008	BS EN 60034-18-31 - ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES
DIN ISO 17359:2011-09	CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
BS EN 61800-4 : 2003	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A.C. POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
BS EN 61241-4:2006 (published 2007-02)	Electrical apparatus for use in the presence of combustible dust Type of protection 'pD'
PREN 14492-1 : DRAFT 2015	CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
11/30229676 DC : 0	BS ISO 8528-5 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
06/30159940 DC : 0	BS EN 60034-15 - ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF ROTATING A.C. - MACHINES WITH FORM-WOUND STATOR COILS
BS EN 50281-1-1 : 1999	ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - ELECTRICAL APPARATUS PROTECTED BY ENCLOSURES - CONSTRUCTION AND TESTING
EN 61800-2:2015	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 2: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE SPEED A.C. POWER DRIVE SYSTEMS (IEC 61800-2:2015)
13/30278886 DC : 0	BS EN 60092-501 - ELECTRICAL INSTALLATIONS IN SHIPS - PART 501: SPECIAL FEATURES - ELECTRIC PROPULSION PLANT
API 616 : 2011	GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
IEEE 1095 : 2012	GUIDE FOR THE INSTALLATION OF VERTICAL GENERATORS AND GENERATOR/MOTORS FOR HYDROELECTRIC APPLICATIONS
CEI EN 61400-22 : 2011	WIND TURBINES - PART 22: CONFORMITY TESTING AND CERTIFICATION
13/30294866 DC : 0	BS EN 61058-1 - SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
BS EN 60034-15:2009	Rotating electrical machines Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
I.S. EN 60034-29:2008	ROTATING ELECTRICAL MACHINES - PART 29: EQUIVALENT LOADING AND SUPERPOSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
10/30200372 DC : 0	BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
UNI EN 15714-2 : 2009	INDUSTRIAL VALVES - ACTUATORS - PART 2: ELECTRIC ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
DD CLC/TS 60034-31 : 2011	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
05/30139105 DC : DRAFT SEP 2005	IEC 61800-5-1 ED 2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
IEC TR 62001:2009	High-voltage direct current (HVDC) systems - Guidebook to the specification and design evaluation of A.C. filters
07/30161347 DC : 0	BS EN 60034-30 - ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED THREE-PHASE CAGE INDUCTION MOTORS
IEEE 95 : 2002	RECOMMENDED PRACTICE FOR INSULATION TESTING OF AC ELECTRIC MACHINERY (2300 V AND ABOVE) WITH HIGH DIRECT VOLTAGE
VDE 0160-109-1 : 2018-01	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM) (IEC 61800-9-1:2017)
NBR ISO 8528-3 : 2014	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
NBR IEC 61241-4 : 2009	ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 4: TYPE OF PROTECTION
BS EN ISO 5801:2017	Fans. Performance testing using standardized airways
08/30176298 DC : DRAFT JAN 2008	BS EN 62477-1 - SAFETY REQUIREMENTS FOR POWER SEMICONDUCTOR CONVERTER SYSTEMS - PART 1: GENERAL
14/30278882 DC : 0	BS EN 60079-7 IEC 60079-7 ED. 5.0 - EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
09/30205068 DC : 0	BS EN 1151-1 - PUMPS - ROTODYNAMIC PUMPS - CIRCULATION PUMPS HAVING A RATED POWER INPUT NOT EXCEEDING 200 W FOR HEATING INSTALLATIONS AND DOMESTIC HOT WATER INSTALLATIONS - PART 1: GENERAL REQUIREMENTS, TESTING, MARKING
EN ISO 5801:2017	FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS (ISO 5801: 2017)
NF EN ISO 5801 : 2017	FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS
15/30256504 DC : 0	BS EN 60034-23 ED 1.0 - ROTATING ELECTRICAL MACHINES - PART 23: REPAIR, OVERHAUL AND RECLAMATION
DD CLC/TS 50537-3 : 2010	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 3: WATER PUMP FOR TRACTION CONVERTERS
GOST R 52350.1 : 2005	ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 1: FLAMEPROOF ENCLOSURES "D"
ISO 19372:2015	Microturbines applications — Safety
14/30297346 DC : 0	BS ISO 8528-8 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 8: GENERATING SETS
DD IEC TS 62257-7-3 : 2008	RECOMMENDATIONS FOR SMALL RENEWABLE ENERGY AND HYBRID SYSTEMS FOR RURAL ELECTRIFICATION - PART 7-3: GENERATOR SET - SELECTION OF GENERATOR SETS FOR RURAL ELECTRIFICATION SYSTEMS
BS EN 60694 : 1997	COMMON SPECIFICATION FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
API 675 : 2012	POSITIVE DISPLACEMENT PUMPS - CONTROLLED VOLUME FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
10/30187796 DC : DRAFT DEC 2010	BS EN 14161 - PETROLEUM AND NATURAL GAS INDUSTRIES - PIPELINE TRANSPORTATION SYSTEMS
14/30300075 DC : 0	BS EN 60034-12 ED 3.0 - ROTATING ELECTRICAL MACHINES - PART 12: STARTING PERFORMANCE OF SINGLE-SPEED THREE-PHASE CAGE INDUCTION MOTORS
IEC 60079-0:2017	Explosive atmospheres - Part 0: Equipment - General requirements
I.S. EN 60947-6-2:2003	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - MULTIPLE FUNCTION EQUIPMENT - CONTROL AND PROTECTIVE SWITCHING DEVICES (OR EQUIPMENT) (CPS)
NF EN 60034-8 : 2008 AMD 1 2014	ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
I.S. EN 88528-11:2004	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - ROTARY UNINTERRUPTIBLE POWER SYSTEMS - PERFORMANCE REQUIREMENTS AND TEST METHODS
IEC TR 62001-1:2016	High-voltage direct current (HVDC) systems - Guidance to the specification and design evaluation of AC filters - Part 1: Overview
BS EN 50216-7:2002	Power transformers and reactor fittings Electric pumps for transformer oil
01/202984 DC : DRAFT APR 2001	IEC 60034-11 ED.2 - THERMAL PROTECTION
DIN ISO 8528-1:1997-11	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 1: APPLICATION, RATINGS AND PERFORMANCE
CEI EN 60034-3 : 2011	ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
08/30186575 DC : DRAFT JULY 2008	BS EN 60079-15 ED. 4 - EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
API 689 : 2007	COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT
CEI EN 60034-15 : 2009	ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF FORM-WOUND STATOR COILS FOR ROTATING A.C. MACHINES
BS EN 50598-1 : 2014	ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
OVE/ONORM EN 60034-5 : 2007	ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
11/30206274 DC : 0	BS EN 60349-4 - ELECTRIC TRACTION ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
PD IEC/TR 62001-4:2016	High-voltage direct current (HVDC) systems. Guidance to the specification and design evaluation of AC filters Equipment
NF EN 60034 18-1 : 2010	ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
14/30284736 DC : 0	BS EN ISO 5801 - FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS
DIN ISO 8528-4:1997-11	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROL AND SWITCHGEAR
13/30280187 DC : 0	BS EN 50598-2 - ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
PD IEC/TR 61000-3-15:2011 (published 2011-10)	Electromagnetic compatibility (EMC) Limits. Assessment of low frequency electromagnetic immunity and emission requirements for dispersed generation systems in LV network
BS EN 60034-18-32:2010 (published 2011-02)	Rotating electrical machines Functional evaluation of insulation systems. Test procedures for form-wound windings. Evaluation by electrical endurance
CSA C22.2 No. 60079.1 : 2016	EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
IEC 60079-7:2015+AMD1:2017 CSV	Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
BS 7458-2(1991) : 1991	TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINERY - SURVEY METHOD
BS IEC 61241-4 : 2001	ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - TYPE OF PROTECTION "PD"
BS EN 15714-2 : 2009	INDUSTRIAL VALVES - ACTUATORS - PART 2: ELECTRIC ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
DIN EN 15268 E : 2008	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
13/30252783 DC : 0	BS EN 50502 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRIC EQUIPMENT IN TROLLEY BUSES - SAFETY REQUIREMENTS AND CONNECTION SYSTEMS
17/30341578 DC : DRAFT MAY 2017	BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
13/30248785 DC : 0	BS EN 61800-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 2: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE FREQUENCY A.C. POWER DRIVE SYSTEMS
10/30238295 DC : 0	BS EN 60034-28 - ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS
CLC/TS 50537-2 : 2010	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 2: PUMP FOR INSULATING LIQUID FOR TRACTION TRANSFORMERS AND REACTORS
ISO 21927-3:2006	Smoke and heat control systems Part 3: Specification for powered smoke and heat exhaust ventilators
UNI CEI EN 45510-2-5 : 2011	GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS
NF EN 60034-5 : 2001 AMD 1 2007	ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
DD IEC TS 60034-31 : DRAFT JULY 2010	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
05/30138181 DC : DRAFT AUG 2005	IEC 60034-8 ED 3 - ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
14/30271543 DC : 0	BS EN ISO 13350 - INDUSTRIAL FANS - PERFORMANCE TESTING OF JET FANS
I.S. EN 61116:1995	ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS
UNE-EN 60034-28:2013	Rotating electrical machines - Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors
BS EN 60034-4 : 2008	ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
BS EN 60034-5 : 2001	ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
BS EN 60034-18-42:2017	ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS (IEC 60034-18-42:2017)
CEI UNI EN 45510-2-5 : 2006	GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS
GOST R ISO 8528-4 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
DD CLC/TS 60034-20-1 : 2004	ROTATING ELECTRICAL MACHINES - PART 20-1: CONTROL MOTORS - STEPPING MOTORS
BS EN 60034-2-2:2010	Rotating electrical machines Specific methods for determining separate losses of large machines from tests. Supplement to IEC 60034-2-1
04/30123544 DC : DRAFT OCT 2004	IEC 60079-1 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 1: FLAMEPROOF ENCLOSURES 'D'
DIN EN 15268:2008-11	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP
13/30280184 DC : 0	BS EN 50598-1 - ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
02/207221 DC : DRAFT JULY 2002	IEC 60079-1 ED.5 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 1: FLAMEPROOF ENCLOSURES "D"
BS EN 60034-14:2004	Rotating electrical machines Mechanical vibration of certain machines with shaft heights 56 mm and higher. Measurement, evaluation and limits of vibration severity
UNE-EN 61400-2:2015	Wind turbines - Part 2: Small wind turbines
NBR IEC 60079-15 : 2012	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
ISA 61241-2 : 2006	ELECTRICAL APPARATUS FOR USE IN ZONE 21 AND ZONE 22 HAZARDOUS (CLASSIFIED) LOCATIONS - PROTECTION BY PRESSURIZATION "PD"
BS EN 60034-30-1 : 2014	ROTATING ELECTRICAL MACHINES - PART 30-1: EFFICIENCY CLASSES OF LINE OPERATED AC MOTORS (IE CODE)
NF EN ISO 5802 : 2009 AMD 1 2015	INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU
11/30247355 DC : 0	BS EN 60034-30 ED 2 - ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS (IE-CODE)
BS EN 60034-18-34 : 2012	ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
BS EN 15268 : 2008	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
18/30368743 DC (published 2018-04)	BS EN 60947-6-2. Low-voltage switchgear and controlgear Part 6-2. Multiple function equipment. Control and protective switching devices (or equipment) (CPS)
15/30330275 DC : 0	BS EN 60034-4 ED 4.0 - ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
BS ISO 3977-3:2004	Gas turbines. Procurement Design requirements
BS EN 60034-18-1 : 2010	ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
DD CLC/TS 60034-25 : 2008	ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
I.S. EN 60034-18-34:2012	ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS (IEC 60034-18-34:2012 (EQV))
BS ISO 3977-8 : 2002	GAS TURBINES - PROCUREMENT - PART 8: INSPECTION, TESTING, INSTALLATION AND COMMISSIONING
NBR IEC 60034-9 : 2011	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
UNE-EN ISO 13350:2016	Fans - Performance testing of jet fans (ISO 13350:2015)
I.S. EN 60079-14:2014	EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
11/30247086 DC : 0	BS EN 60079-1 ED. 7.0 - EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES "D"
UNE-EN 60027-4:2011	Letter symbols to be used in electrical technology -- Part 4: Rotating electric machines
CSA E60079.7 : 2003	ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 7: INCREASED SAFETY "E"
BS PD IEC TS 60034-32 : 2016	ROTATING ELECTRICAL MACHINES - PART 32: MEASUREMENT OF STATOR END-WINDING VIBRATION AT FORM-WOUND WINDINGS
NF EN 50016 : 2004	ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PRESSURIZED APPARATUS 'P'
DIN VDE 0660-102 : 1992	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
BS PD IEC/TS 60034-30-2 : 2016	ROTATING ELECTRICAL MACHINES - PART 30-2: EFFICIENCY CLASSES OF VARIABLE SPEED AC MOTORS (IE-CODE)
I.S. EN 60034-22:2009	ROTATING ELECTRICAL MACHINES - PART 22: AC GENERATORS FOR RECIPROCATING INTERNAL COMBUSTION (RIC) ENGINE DRIVEN GENERATING SETS
BS 7458-1(1991) : 1991	TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINERY - ENGINEERING METHOD FOR FREE-FIELD CONDITIONS OVER A REFLECTING PLANE
DD IEC PAS 62001 : 2004	GUIDE TO THE SPECIFICATION AND DESIGN EVALUATION OF A.C. FILTERS FOR HVDC SYSTEMS
02/203983 DC : DRAFT MAR 2002	IEC 60034-3. ED.5 - ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR CYLINDRICAL ROTOR SYNCHRONOUS MACHINES
CLC/TS 50537-3 : 2010	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 3: WATER PUMP FOR TRACTION CONVERTERS
NBR IEC 61892-3 : 2013	MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 3: EQUIPMENTS
BS EN 12693 : 2008	REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
04/30111859 DC : 0	IEC 62271-1 - HIGH-VOLTAGE SWITCHGEAR AND CONTROL GEAR - PART 1: COMMON SPECIFICATIONS
BS 4999-115(1992) : 1992	GENERAL REQUIREMENTS FOR ROTATING ELECTRICAL MACHINES - IMPULSE VOLTAGE WITHSTAND LEVELS OF ROTATING A.C. MACHINES WITH FORM-WOUND STATOR COILS
03/113813 DC : 0	IEC 60034-2. ED.4 - ROTATING ELECTRICAL MACHINES - PART 2: METHODS FOR DETERMINING LOSSES AND EFFICIENCY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES)
08/30184583 DC : DRAFT JUNE 2008	BS IEC/TS 60034-18-32 - ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - ELECTRICAL EVALUATION OF INSULATION SYSTEMS USED IN ROTATING ELECTRICAL MACHINES
BS EN 60027-4 : 2007	LETTER SYMBOLS TO BE USED IN ELECTRIC TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
NBR IEC 60034-5 : 2009	ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
BS ISO 13380 : 2002	CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES ON USING PERFORMANCE PARAMETERS
NF EN 60079-15 : 2010	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
BS ISO 8528-3:2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
UNE-EN 50598-2:2015	Ecodesign for power drive systems, motor starters, power electronics & their driven applications - Part 2: Energy efficiency indicators for power drive systems and motor starters
NBR 16476 : 2016	CHANGER REMOTE LIQUID HEAT AND BUSY AIR BY FORCED CONVECTION (DRY COOLER) - TEST PROCEDURES FOR DETERMINING PERFORMANCE
NBR 17094-2 : 2016	ROTATING ELECTRICAL MACHINES - PART 2: SINGLE-PHASE INDUCTION MOTORS - REQUIREMENTS
I.S. EN 50598-1:2014	ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
NF EN 60034-18-32 : 2011	ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION BY ELECTRICAL ENDURANCE
I.S. EN 50216-12:2011	POWER TRANSFORMER AND REACTOR FITTINGS - PART 12: FANS
NBR IEC 60947-4-2 : 2011	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
I.S. EN ISO 5801:2017	FANS - PERFORMANCE TESTING USING STANDARDIZED AIRWAYS (ISO 5801: 2017)
06/30151149 DC : DRAFT JUN 2006	BS IEC 60034-3 - ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
BS EN 45510-2-5 : 2002	GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS
BS EN 50016 : 2002	ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PRESSURIZED APPARATUS "P"
07/30065083 DC : DRAFT JUNE 2007	BS EN 60027-4 - LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
I.S. EN 60335-1:2012	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS
I.S. EN 61800-9-1:2017	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM)
03/316172 DC : DRAFT SEP 2003	ISO 8528-3 - RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 3: ALTERNATING CURRENT GENERATORS FOR GENERATING SETS
NF ISO 3977-8 : 2002	GAS TURBINES - PROCUREMENT - PART 8: INSPECTION, TESTING, INSTALLATION AND COMMISSIONING
CSA C22.2 No. 60079.0 : 2015	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
98/201424 DC : DRAFT MARCH 1998	IEC 61972 - METHOD FOR DETERMINING LOSSES AND EFFICIENCY OF THREE-PHASE, CAGE INDUCTION MOTORS
BS 848-10(1999) : 1999	FANS FOR GENERAL PURPOSES - PART 10: PERFORMANCE TESTING OF JET FANS
CSA E60079.15 : 2002 : R2011	ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL APPARATUS WITH TYPE OF PROTECTION "n"
09/30194359 DC : 0	BS EN 60034-18-34 - ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
ISO 1680-2:1986	Acoustics Test code for the measurement of airborne noise emitted by rotating electrical machinery Part 2: Survey method
NF EN 60947-4-2 : 2012	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - A.C. SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
CSA E60079.15 : 2002	ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - ELECTRICAL APPARATUS WITH TYPE OF PROTECTION "n"
08/30180328 DC : DRAFT MAR 2008	BS EN 61800-8 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 8: SPECIFICATION OF VOLTAGE ON THE POWER INTERFACE
UNE-EN 15714-2:2010	Industrial valves - Actuators - Part 2: Electric actuators for industrial valves - Basic requirements
BS EN 60034-9 : 2005	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
09/30182101 DC : 0	BS EN 60349-1 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTOR-FED ALTERNATING CURRENT MOTORS
I.S. EN 60349-4:2013	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER (IEC 60349-4:2012 (EQV))
CSA C22.2 No. 61058.1 : 2009	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
NF EN 60034-3 : 2008	ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
PREN 50502 : DRAFT 2013	RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRIC EQUIPMENT IN TROLLEY BUSES - SAFETY REQUIREMENTS AND CONNECTION SYSTEMS
IEC 60079-1 REDLINE : 7ED 2014	EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
BS EN 60204-11 : 2001	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
NF EN 88528-11 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 11: ROTARY UNINTERRUPTIBLE POWER SYSTEMS - PERFORMANCE REQUIREMENTS AND TEST METHODS
CSA ISO 50004 : 2015	ENERGY MANAGEMENT SYSTEMS - GUIDANCE FOR THE IMPLEMENTATION, MAINTENANCE AND IMPROVEMENT OF AN ENERGY MANAGEMENT SYSTEM
GOST R ISO 8528-5 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
I.S. EN 60034-30:2009	ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS
CEI EN 50216-7 : 2002	POWER TRANSFORMER AND REACTOR FITTINGS - PART 7: ELECTRIC PUMPS FOR TRANSFORMER OIL
CEI EN 61116 : 1996	ELECTROMECHANICAL EQUIPMENT GUIDE FOR SMALL HYDROELECTRIC INSTALLATIONS
BIS IS/IEC 60079-7 : 2006	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
CEI EN 60034-2-2 : 2011	ROTATING ELECTRICAL MACHINES - PART 2-2: SPECIFIC METHODS FOR DETERMINING SEPARATE LOSSES OF LARGE MACHINES FROM TESTS - SUPPLEMENT TO IEC 60034-2-1
DIN EN 15714-2:2010-02	Industrial valves - Actuators - Part 2: Electric actuators for industrial valves - Basic requirements
FM 1319 : 2018	CENTRIFUGAL FIRE PUMPS (HORIZONTAL, END SUCTION TYPE)
NF EN 60034-30 : 2009	ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS (IE-CODE)
CSA C22.2 NO. 60947-4-1:14 (R2019)	Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters ( Bi-national standard, with UL 60947-4-1)
NBR IEC 61058-1 : 2004	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
CSA C22.2 No. 60079-7 : 2016	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
UNE-EN 60947-4-2:2013	Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters
API 616 REDLINE : 2011	GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
I.S. EN 60079-1:2014	EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'
IEC 61936-1:2010+AMD1:2014 CSV	Power installations exceeding 1 kV a.c. - Part 1: Common rules
CEI EN 60349-2 : 2012	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
NF EN 60947 6-2 : 2003 AMD 1 2007	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 6-2: MULTIPLE FUNCTION EQUIPMENT - CONTROL AND PROTECTIVE SWITCHING DEVICES (OR EQUIPMENT) (CPS)
PREN 50598-1 : DRAFT 2013	ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
NF EN 60034-9 : 2005 AMD 1 2007	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
CEI EN 60034-18-34 : 2013	ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
NBR IEC 60947-4-1 : 2018	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
BIS IS/IEC 60079-31 : 2008	EXPLOSIVE ATMOSPHERES - PART 31: EQUIPMENT DUST IGNITION PROTECTION BY ENCLOSURE "T"
IEEE 45.6:2016	IEEE Recommended Practice for Electrical Installations on Shipboard--Electrical Testing
ISO 50004:2014	Energy management systems Guidance for the implementation, maintenance and improvement of an energy management system
IEC 60092-501:2013	Electrical installations in ships - Part 501: Special features - Electric propulsion plant
GOST R ISO 8528-1 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 1: APPLICATION, RATINGS AND PERFORMANCE
CLC/TS 60034-18-34 : 2004	ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
API 546 : 2008	BRUSHLESS SYNCHRONOUS MACHINES - 500 KVA AND LARGER
PREN 50598-2 : DRAFT 2013	ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
API 610 : 2010	CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
API 610 REDLINE : 2010	CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
I.S. EN 60079-7:2015	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
IEEE C50.13 : 2014	CYLINDRICAL-ROTOR 50 HZ AND 60 HZ, SYNCHRONOUS GENERATORS RATED 10 MVA AND ABOVE
BS IEC 60092-501:2013 (published 2013-10)	Electrical installations in ships Special features. Electric propulsion plant
I.S. EN 50216-7:2002	POWER TRANSFORMER AND REACTOR FITTINGS - PART 7: ELECTRIC PUMPS FOR TRANSFORMER OIL
BS EN 60079-7 : 2015	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015)
FM 1312 : 2018	CENTRIFUGAL FIRE PUMPS (VERTICAL-SHAFT, TURBINE TYPE)
CEI EN 60034-18-1 : 2011	ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
CEI EN 60034-18-21 : 2014	ROTATING ELECTRICAL MACHINES - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION
S.R. CLC/TS 50537-3:2010	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 3: WATER PUMP FOR TRACTION CONVERTERS
EN 61800-9-2 : 2017	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017)
I.S. EN 60694:1999	COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
I.S. EN 50019:2001	ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY "E"
CEI EN 60034-29 : 2009	ROTATING ELECTRICAL MACHINES - PART 29: EQUIVALENT LOADING AND SUPERPOSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
CEI CLC/TS 50537-2 : 2011	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 2: PUMP FOR INSULATING LIQUID FOR TRACTION TRANSFORMERS AND REACTORS
IEC TS 60034-2-3:2013	Rotating electrical machines - Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC induction motors
CSA C22.3 No. 61936-1 : 2008	POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
IEEE 841 : 2009	PETROLEUM AND CHEMICAL INDUSTRY - PREMIUM-EFFICIENCY, SEVERE-DUTY, TOTALLY ENCLOSED FAN-COOLED (TEFC) SQUIRREL CAGE INDUCTION MOTORS - UP TO AND INCLUDING 370 KW (500 HP)
CSA C22.2 NO. 60947-4-2:14 (R2019)	Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters ( Bi-national standard, with UL 60947-4-2)
NF EN 60034-18-34 : 2013	ROTATING ELECTRICAL MACHINES - PART 18-34: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS
I.S. EN 60034-5:2001	ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION
ISO 14990-1:2016	Earth-moving machinery Electrical safety of machines utilizing electric drives and related components and systems Part 1: General requirements
CEI EN 60034-18-42 : 1ED 2017	ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS
IEEE C37.102 : 2006	GUIDE FOR AC GENERATOR PROTECTION
CSA C61400-2 : 2008 : R2013	WIND TURBINES - PART 2: DESIGN REQUIREMENTS FOR SMALL WIND TURBINES
OVE/ONORM EN 60034-3 : 2009	ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
IEC TR 61000-3-15:2011	Electromagnetic compatibility (EMC) - Part 3-15: Limits - Assessment of low frequency electromagnetic immunity and emission requirements for dispersed generation systems in LV network
BS EN 62271-1:2017	High-voltage switchgear and controlgear Common specifications for alternating current switchgear and controlgear
BS EN 60335-1 : 2012	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
BS EN 60034-8 : 2007	ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
NF EN 60034-18-42 : 2017	ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS
IEC 61058-1:2016	Switches for appliances - Part 1: General requirements
EN 60204-1 : 2006 COR 2010	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
CSA C61400-2 : 2008 : R2018	WIND TURBINES - PART 2: DESIGN REQUIREMENTS FOR SMALL WIND TURBINES
I.S. CLC TS 60034-25:2005	ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
BS EN ISO 5802 : 2008	INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU
UNI EN 15268 : 2009	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
BS EN 15194:2017	Cycles. Electrically power assisted cycles. EPAC Bicycles
BS EN 61058-1 : 2002	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
I.S. EN 61058-1:2002	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
BS EN 60079-0 : 2012	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
I.S. EN 60079-15:2010	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
NBR IEC 60694 : 2006	COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
IEC 60079-0 REDLINE : 7.0	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
EN 62271-1:2017	HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS FOR ALTERNATING CURRENT SWITCHGEAR AND CONTROLGEAR (IEC 62271-1:2017)
CSA C61400-2:2008	WIND TURBINES - PART 2: DESIGN REQUIREMENTS FOR SMALL WIND TURBINES
S.R. CLC/TS 50537-2:2010	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 2: PUMP FOR INSULATING LIQUID FOR TRACTION TRANSFORMERS AND REACTORS
IEC TS 60034-32:2016	Rotating electrical machines - Part 32: Measurement of stator end-winding vibration at form-wound windings
I.S. EN 60034-18-21:2013	ROTATING ELECTRICAL MACHINES - - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIREWOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION (IEC 60034-18-21:2012 (EQV))
I.S. EN 60034-9:2005	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
I.S. EN 15714-2:2009	INDUSTRIAL VALVES - ACTUATORS - PART 2: ELECTRIC ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
I.S. EN 60947-4-2:2012	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
I.S. EN ISO 13350:2015	FANS - PERFORMANCE TESTING OF JET FANS (ISO 13350:2015)
I.S. EN 60034-14:2004	ROTATING ELECTRICAL MACHINES - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY
I.S. EN 60947-4-1:2010	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009 (EQV))
NF EN 60034-14 : 2004 AMD 1 2007	ROTATING ELECTRICAL MACHINES - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY
ISO 1680-1:1986	Acoustics Test code for the measurement of airborne noise emitted by rotating electrical machinery Part 1: Engineering method for free-field conditions over a reflecting plane
I.S. EN 60034-3:2008	ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
ISO 17359:2018	Condition monitoring and diagnostics of machines General guidelines
I.S. EN 60034-28:2013	ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS (IEC 60034-28:2012 (EQV))
UNE-EN 50598-1:2015	Ecodesign for power drive systems, motor starters, power electronics & their driven applications - Part 1: General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA), and semi analytic model (SAM)
I.S. EN 60034-18-42:2017	ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS
I.S. EN 60034-15:2009	ROTATING ELECTRICAL MACHINES - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF FORM-WOUND STATOR COILS FOR ROTATING A.C. MACHINES
CEI EN 60034-4 : 2009	ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
CEI EN 60947-4-2 : 2013	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-2: CONTACTORS AND MOTOR-STARTERS - AC SEMICONDUCTOR MOTOR CONTROLLERS AND STARTERS
CEI EN 61800-9-2 : 1ED 2017	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
CEI EN 60349-1 : 2012	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
CLC/TS 60034-20-1 : 2004	ROTATING ELECTRICAL MACHINES - PART 20-1: CONTROL MOTORS - STEPPING MOTORS
ISO 3977-3:2004	Gas turbines Procurement Part 3: Design requirements
ISO 8528-4:2005	Reciprocating internal combustion engine driven alternating current generating sets Part 4: Controlgear and switchgear
BS ISO 8528-5:2013	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
ISO 13380:2002	Condition monitoring and diagnostics of machines General guidelines on using performance parameters
BS IEC 61892-5:2014	Mobile and fixed offshore units. Electrical installations Mobile units
NF EN 61800 5-1 : 2007	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
I.S. EN 60034-19:2014	ROTATING ELECTRICAL MACHINES - PART 19: SPECIFIC TEST METHODS FOR D.C. MACHINES ON CONVENTIONAL AND RECTIFIER-FED SUPPLIES
I.S. EN 50598-2:2014	ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
BS IEC 61892-1:2015	Mobile and fixed offshore units. Electrical installations General requirements and conditions
ISO 18652:2005	Building construction machinery and equipment External vibrators for concrete
FM 1370 : 2018	CENTRIFUGAL FIRE PUMPS (VERTICAL SHAFT, TURBINE TYPE, BARREL)
FM 1311 : 2018	CENTRIFUGAL FIRE PUMPS SPLIT-CASE TYPE (AXIAL OR RADIAL)
GOST R 52350.15 : 2005	ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 15: CONSTRUCTION, TEST AND MARKING OF TYPE OF PROTECTION "N" ELECTRICAL APPARATUS
ISO/TS 19466:2017	Electrically propelled mopeds and motorcycles Test method for evaluating performance of regenerative braking systems
CEI EN 60034-22 : 2011	ROTATING ELECTRICAL MACHINES - PART 22: AC GENERATORS FOR RECIPROCATING INTERNAL COMBUSTION (RIC) ENGINE DRIVEN GENERATING SETS
ISO 8528-8:2016	Reciprocating internal combustion engine driven alternating current generating sets Part 8: Requirements and tests for low-power generating sets
IEC 60092-204:1987	Electrical installations in ships. Part 204: System design - Electric and electrohydraulic steering gear
IEC 61892-5:2014	Mobile and fixed offshore units - Electrical installations - Part 5: Mobile units
BIS IS/IEC 62271-1 : 2007	HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS
I.S. EN 60034-18-32:2010	ROTATING ELECTRICAL MACHINES - PART 18-32: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION BY ELECTRICAL ENDURANCE
16/30341165 DC : 0	BS EN 14492-2 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
CEI EN 60034-11 : 2005	ROTATING ELECTRICAL MACHINES - PART 11: THERMAL PROTECTION
BIS IS/ISO 8528-5 : 2005(R2014)	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 5: GENERATING SETS
S.R. CLC/TS 60034-31:2011	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
I.S. EN 60034-11:2004	ROTATING ELECTRICAL MACHINES - PART 11: THERMAL PROTECTION
I.S. EN 61241-4:2007	ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 4: TYPE OF PROTECTION 'PD'
I.S. EN 60034-2-2:2010	ROTATING ELECTRICAL MACHINES - PART 2-2: SPECIFIC METHODS FOR DETERMINING SEPARATE LOSSES OF LARGE MACHINES FROM TESTS - SUPPLEMENT TO IEC 60034-2-1
BS EN 61400-2:2014 (published 2014-10)	Wind turbines Small wind turbines
BWB TL 3405-0005 : 1ED 2004
NBR ISO 14224 : 2011	PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT
IEC TS 60034-20-1:2002	Rotating electrical machines - Part 20-1: Control motors - Stepping motors
CSA C22.2 No. 61241-4 : 2012	ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 4: TYPE OF PROTECTION 'PD'
NBR IEC 60079-7 : 2008 ERRATA 2010	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY
I.S. EN 60204-33:2011	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 33: REQUIREMENTS FOR SEMICONDUCTOR FABRICATION EQUIPMENT
BS EN 60079-15 : 2010	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
CSA C22.2 No. 60079-15 : 2016	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
CSA C22.2 No. 61058.1 : 2009 : R2014	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
NF EN 60034-28 : 2013	ROTATING ELECTRICAL MACHINES - PART 28: TEST METHODS FOR DETERMINING QUANTITIES OF EQUIVALENT CIRCUIT DIAGRAMS FOR THREE-PHASE LOW-VOLTAGE CAGE INDUCTION MOTORS
VDE 0160-109-2 : 2018-01	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017)
UNE-EN 60034-22:2010	Rotating electrical machines -- Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets
BIS IS/IEC 60947-4-1 : 2000	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4: CONTACTORS AND MOTOR-STARTERS - SECTION 1: ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS
PREN 327 : DRAFT 2012	HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS - TEST PROCEDURES FOR ESTABLISHING PERFORMANCE
I.S. EN 60034-8:2007	ROTATING ELECTRICAL MACHINES - PART 8: TERMINAL MARKINGS AND DIRECTION OF ROTATION
NF EN 60034-29 : 2008	ROTATING ELECTRICAL MACHINES - PART 29: EQUIVALENT LOADING AND SUPERPOSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
CEI EN 60079-15 : 2012	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
BIS IS/IEC 60079-15 : 2005	ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 15: CONSTRUCTION, TEST AND MARKING OF TYPE OF PROTECTION 'N' ELECTRICAL APPARATUS
NBR ISO 8528-12 : 2014	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 12: EMERGENCY POWER SUPPLY TO SAFETY SERVICES
NF EN 61986 : 2004	ROTATING ELECTRICAL MACHINES - EQUIVALENT LOADING AND SUPER-POSITION TECHNIQUES - INDIRECT TESTING TO DETERMINE TEMPERATURE RISE
NF EN 60034-11 : 2005	ROTATING ELECTRICAL MACHINES - PART 11: THERMAL PROTECTION
CEI EN 61800-4 : 2003	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A/C/ POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
NBR IEC 61892-5 : 2017	MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 5: MOBILE UNITS
UNE-EN 60034-18-31:2013	Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines
NBR IEC 61892-1 : 2016	MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 1: GENERAL REQUIREMENTS AND CONDITIONS
I.S. EN 61400-2:2014	WIND TURBINES - PART 2: SMALL WIND TURBINES
EN 60034-18-42:2017	ROTATING ELECTRICAL MACHINES - PART 18-42: PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION TESTS (IEC 60034-18-42:2017)
EN 61936-1 : 2010 AMD 1 2014	POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES (IEC 61936-1:2010/A1:2014)
NF EN 60034-4 : 2008	ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
I.S. EN 60027-4:2007	LETTER SYMBOLS TO BE USED IN ELECTRIC TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
ISO 8528-3:2005	Reciprocating internal combustion engine driven alternating current generating sets Part 3: Alternating current generators for generating sets
I.S. EN 61936-1:2010	POWER INSTALLATIONS EXCEEDING 1 KV A.C. - PART 1: COMMON RULES
08/30176387 DC : DRAFT JAN 2008	BS EN 60034-18-21 - ROTATING ELECTRICAL MACHINES - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION
09/30152273 DC : 0	BS IEC/TS 60034-20-2 - ROTATING ELECTRICAL MACHINES - PART 20-2: PERFORMANCE CHARACTERISTICS AND TESTING SPECIFICATIONS FOR BRUSHLESS PERMANENT MAGNET MOTORS
BS EN 61800-2:2015 (published 2015-10)	Adjustable speed electrical power drive systems General requirements. Rating specifications for low voltage adjustable speed a.c. power drive systems
BS EN 60349-1 : 2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTOR-FED ALTERNATING CURRENT MOTORS
BS PD IEC TR 62001 : 2009	HIGH-VOLTAGE DIRECT CURRENT (HVDC) SYSTEMS - GUIDEBOOK TO THE SPECIFICATION AND DESIGN EVALUATION OF A.C. FILTERS
BS EN 61800-9-1:2017 (published 2017-11)	Adjustable speed electrical power drive systems Ecodesign for power drive systems, motor starters, power electronics and their driven applications. General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA) and semi analytic model (SAM)
BS EN ISO 13350:2015	Fans. Performance testing of jet fans
01/202453 DC : DRAFT APRIL 2001	IEC 60034-9 ED.4 - ROTATING ELECTRICAL MACHINERY - PART 9: NOISE LIMITS
BS EN 60034-3 : 2008	ROTATING ELECTRICAL MACHINES - PART 3: SPECIFIC REQUIREMENTS FOR SYNCHRONOUS GENERATORS DRIVEN BY STEAM TURBINES OR COMBUSTION GAS TURBINES
12/30261858 DC : 0	BS EN 60079-31/ED 2 - EXPLOSIVE ATMOSPHERES - PART 31: EQUIPMENT DUST IGNITION PROTECTION BY ENCLOSURE 'T'
BS EN 50019 : 2000	ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY 'E'
BIS IS/ISO 8528-4 : 2005(R2014)	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 4: CONTROLGEAR AND SWITCHGEAR
17/30347395 DC : 0	BS EN 60034-2-3 - ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC MOTOR
I.S. EN 60349-2:2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
I.S. EN ISO 8528-13:2016	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 13: SAFETY (ISO/DIS 8528-13:2014)
ISO 13350:2015	Fans Performance testing of jet fans
CSA C22.2 No. 61058.1 : 2009 : INC : UPD 1 : 2013	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
CLC/TS 60034-31 : 2011	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
DIN EN 61800-9-1 : 2018-01	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM) (IEC 61800-9-1:2017)
IEC 61058-1 REDLINE : 4ED 2016	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
UNE-EN 60349-4:2013	Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
DD CLC/TS 50537-2 : 2010	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 2: PUMP FOR INSULATING LIQUID FOR TRACTION TRANSFORMERS AND REACTORS
UNE-EN 60079-1:2015	Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
CEI CLC/TS 50537-3 : 2011	RAILWAY APPLICATIONS - MOUNTED PARTS OF THE TRACTION TRANSFORMER AND COOLING SYSTEM - PART 3: WATER PUMP FOR TRACTION CONVERTERS
CEI EN 88528-11 : 2005	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 11: ROTARY UNINTERRUPTIBLE POWER SYSTEMS - PERFORMANCE REQUIREMENTS AND TEST METHODS
I.S. EN 12693:2008	REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
I.S. EN 61800-4:2003	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A.C. POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
I.S. EN 61400-22:2011	WIND TURBINES - PART 22: CONFORMITY TESTING AND CERTIFICATION
I.S. EN ISO 5802:2008	INDUSTRIAL FANS - PERFORMANCE TESTING IN SITU (ISO 5802:2001)
I.S. EN 60034-4:2008	ROTATING ELECTRICAL MACHINES - PART 4: METHODS FOR DETERMINING SYNCHRONOUS MACHINE QUANTITIES FROM TESTS
I.S. EN 61800-2:2015	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 2: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE SPEED A.C. POWER DRIVE SYSTEMS
I.S. EN 62271-1:2017	HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS FOR ALTERNATING CURRENT SWITCHGEAR AND CONTROLGEAR
IEC 61972:2002	Method for determining losses and efficiency of three-phase cage induction motors
I.S. EN 60034-18-1:2010	ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
IEC 61800-9-2:2017	Adjustable speed electrical power drive systems - Part 9-2: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - Energy efficiency indicators for power drive systems and motor starters
IEC TR 62001-4:2016	High-voltage direct current (HVDC) systems - Guidance to the specification and design evaluation of AC filters - Part 4: Equipment
IEC PAS 62001:2004	Guide to the specification and design evaluation of a.c. filters for HVDC systems
IEC TS 61800-8:2010	Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
IEC TS 60034-17:2006	Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide
IEC 61892-1:2015	Mobile and fixed offshore units - Electrical installations - Part 1: General requirements and conditions
IEC 60947-4-1:2009+AMD1:2012 CSV	Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters
IEC TS 60034-31:2010	Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
IEC 60092-301:1980	Electrical installations in ships - Part 301: Equipment - Generators and motors
I.S. EN 15194:2017	CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES
IEC TS 62257-7-3:2008	Recommendations for small renewable energy and hybrid systems for rural electrification - Part 7-3: Generator set - Selection of generator sets for rural electrification systems
IEC 61800-9-1:2017	Adjustable speed electrical power drive systems - Part 9-1: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - General requirements for setting energy efficiency standards for power driven equipment using the extended product approach (EPA) and semi analytic model (SAM)
IEC TS 60034-23:2003	Rotating electrical machines - Part 23: Specification for the refurbishing of rotating electrical machines
IEC 60034-18-42:2017	Rotating electrical machines - Part 18-42: Partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters - Qualification tests
IEC 61892-3:2012	Mobile and fixed offshore units - Electrical installations - Part 3: Equipment
I.S. EN 60204-1:2006	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
IEC 60204-11:2000	Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
IEC 61800-2:2015	Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems
I.S. EN 60204-32:2008	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 32: REQUIREMENTS FOR HOISTING MACHINES
ISO/TR 18569:2004	Safety of machinery Guidelines for the understanding and use of safety of machinery standards
IEC 62271-1:2017	High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
IEC TS 60034-18-34:2000	Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems
I.S. EN 61800-5-1:2007	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
I.S. EN 60034-2-1:2014	ROTATING ELECTRICAL MACHINES - PART 2-1: STANDARD METHODS FOR DETERMINING LOSSES AND EFFICIENCY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES)
IEC 60079-1:2014 RLV	Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
S.R. CWA 15902-1:2009	LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - PART 1: GENERAL REQUIREMENTS (EXCLUDING ALUMINIUM AND STEEL TRUSSES AND TOWERS)
I.S. EN 14492-2:2006	CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
IEC TS 60034-25:2014	Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
IEC 60204-33:2009	Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment
I.S. EN 15268:2008	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
ISO 8528-5:2013	Reciprocating internal combustion engine driven alternating current generating sets Part 5: Generating sets
NFPA 79 : 2018	ELECTRICAL STANDARD FOR INDUSTRIAL MACHINERY
EN 60335-1:2012/A13:2017	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
EN IEC 60079-7:2015/A1:2018	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017)
I.S. EN ISO 13709:2009	CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
DIN EN 12101-3:2015-12	SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
DIN EN 13135-1:2011-04	CRANES - EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT
DIN EN 328:2014-11	HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
DIN EN ISO 1680:2014-04	ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES (ISO 1680:2013)
DIN EN ISO 8528-13 E : 2017	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - PART 13: SAFETY (ISO 8528-13:2016, CORRECTED VERSION 2016-10-15)
DIN EN 327:2014-11	HEAT EXCHANGERS - FORCED CONVECTION AIR COOLED REFRIGERANT CONDENSERS - TEST PROCEDURES FOR ESTABLISHING PERFORMANCE
UNE-EN 50216-12:2011	Power transformer and reactor fittings -- Part 12: Fans
BS EN ISO 13709:2003	CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
IEC 60034-4:2008	Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests
BS EN 12101-3:2015	SMOKE AND HEAT CONTROL SYSTEMS - SPECIFICATION FOR POWERED SMOKE AND HEAT EXHAUST VENTILATORS (FANS)
17/30338554 DC : 0	BS EN 1175 - SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL/ELECTRONIC REQUIREMENTS
13/30294120 DC : 0	BS IEC 61892-5 ED 3.0 - MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 5: MOBILE UNITS
BS EN 328 : 2014	HEAT EXCHANGERS - FORCED CONVECTION UNIT AIR COOLERS FOR REFRIGERATION - TEST PROCEDURES FOR ESTABLISHING THE PERFORMANCE
BS ISO 22734-1 : 2008	HYDROGEN GENERATORS USING WATER ELECTROLYSIS PROCESS - PART 1: INDUSTRIAL AND COMMERCIAL APPLICATIONS
BS 7698-8(1996) : 1996	RECIPROCATING INTERNAL COMBUSTION ENGINE DRIVEN ALTERNATING CURRENT GENERATING SETS - REQUIREMENTS AND TESTS FOR LOW-POWER GENERATING SETS
PD ISO/TR 18569:2004	Safety of machinery. Guidelines for the understanding and use of safety of machinery standards.
02/203840 DC : DRAFT MAY 2002	IEC 60204-1/ED.5.0 - SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
IEC 60204-32:2008	Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
12/30269297 DC : 0	BS EN 60079-14/ED 5 - EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
BS EN ISO 15783 : 2003	SEAL-LESS ROTODYNAMIC PUMPS - CLASS 2 - SPECIFICATION
ISO 22734-1:2008	Hydrogen generators using water electrolysis process Part 1: Industrial and commercial applications
IEC 60034-30:2008	Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
13/30286778 DC : 0	BS EN 60079-1 - EXPLOSIVE ATMOSPHERES - PART 1: EQUIPMENT PROTECTION BY FLAMEPROOF ENCLOSURES 'D'