• IEC 60068-2-3:1969

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  01-08-2001

    Language(s):  English - French, Russian

    Published date:  01-01-1969

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    PREFACE
    1 Scope
    2 Testing chamber
    3 Testing procedure
    4 Recovery
    5 Final measurements
    6 Information required in the relevant specification

    Abstract - (Show below) - (Hide below)

    Describes a continuous test at a steady temperature of 40°C and a relative humidity of 90-95%. The standard test duration is 4 to 56 days.

    General Product Information - (Show below) - (Hide below)

    Committee TC 104
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 2011-2.1KB(1987) : 1987 ENVIRONMENTAL TESTING - TESTS - TEST KB: SALT MIST, CYCLIC (SODIUM CHLORIDE SOLUTION)
    PREN 50290-4-1 : DRAFT 2013 COMMUNICATION CABLES - PART 4-1: GENERAL CONSIDERATIONS FOR THE USE OF CABLES - ENVIRONMENTAL CONDITIONS AND SAFETY ASPECTS
    03/109829 DC : DRAFT JUNE 2003 IEC 60086-3 - PRIMARY BATTERIES - PART 3: WATCH BATTERIES
    05/30136363 DC : DRAFT JUL 2005 IEC 60255-6 ED 3 - ELECTRICAL RELAYS - PART 6: GENERAL REQUIREMENTS FOR MEASURING RELAYS AND PROTECTION EQUIPMENT
    I.S. EN 60491:1996 SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
    PREN 54-5 : DRAFT 2011 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 5: HEAT DETECTORS - POINT DETECTORS
    00/247278 DC : DRAFT DEC 2000
    BS EN 61747-5 : 1998 LIQUID CRYSTAL AND SOLID-STATE DISPLAY DEVICES - PART 5: ENVIRONMENTAL, ENDURANCE AND MECHANICAL TEST METHODS
    05/30137416 DC : 0
    BS CECC50000(1987) : 1987 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: DISCRETE SEMICONDUCTOR DEVICES
    BS EN 61249-8-8 : 1997 MATERIALS FOR INTERCONNECTION STRUCTURES - SECTIONAL SPECIFICATION SET FOR NON-CONDUCTIVE FILMS AND COATINGS - TEMPORARY POLYMER COATINGS
    CEI 45-60 : 2009 NUCLEAR POWER PLANTS - ELECTRICAL EQUIPMENT OF THE SAFETY SYSTEM - QUALIFICATION
    BS 2011-2.1T(1981) : 1981 ENVIRONMENTAL TESTING - TESTS - TEST T - SOLDERING
    BS CECC 64000:1990 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: FILM RESISTOR NETWORKS
    ISO 11614:1999 Reciprocating internal combustion compression-ignition engines Apparatus for measurement of the opacity and for determination of the light absorption coefficient of exhaust gas
    11/30241337 DC : DRAFT JAN 2011 BS EN 61757-1 - FIBRE OPTIC SENSORS - PART 1: GENERIC SPECIFICATION
    07/30162213 DC : 0 BS EN 60747-15 - SEMICONDUCTOR DEVICES - DISCRETE DEVICES - PART 15: ISOLATED POWER SEMICONDUCTOR DEVICES
    08/30195238 DC : 0
    BS EN 60747-5-2 : 2001 DISCRETE SEMICONDUCTOR DEVICES AND INTEGRATED CIRCUITS - PART 5-2: OPTOELECTRONIC DEVICES - ESSENTIAL RATINGS AND CHARACTERISTICS
    BS EN 60873 : 1993 METHODS FOR EVALUATING THE PERFORMANCE OF ELECTRICAL AND PNEUMATIC ANALOGUE CHART RECORDERS FOR USE IN INDUSTRIAL PROCESS CONTROL SYSTEMS
    CEI EN 60512-11-3 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-3: CLIMATIC TESTS TEST 11C: DAMP HEAT, STEADY STATE
    11/30205541 DC : 0 BS EN 54-7 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 7: SMOKE DETECTORS - POINT DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONISATION
    03/106844 DC : DRAFT MAY 2003 ISO 7240-11 - FIRE DETECTION AND ALARM SYSTEMS - PART 11: MANUAL CALL POINTS
    BS 7573-1.1(1992) : 1992 AMD 8338 METHODS OF MEASUREMENT FOR EQUIPMENT USED IN DIGITAL MICROWAVE RADIO TRANSMISSION SYSTEMS - MEASUREMENTS COMMON TO TERRESTRIAL RADIO-RELAY SYSTEMS AND SATELLITE EARTH STATIONS - GENERAL
    ETR 344 : 20001 TERMINAL EQUIPMENT (TE) - THE TECHNICAL FEASIBILITY OF A HARMONIZED PLUG AND SOCKET STANDARD
    DIN 47608-2:1997-10 TERMINAL STRIPS WITH INSULATION DISPLACEMENT CONTACTS FOR TELECOMMUNICATION SYSTEMS; REQUIREMENTS, TESTS
    ISO 10599-2:1997 Car radios Coaxial aerial connectors Part 2: Characteristic values, performance requirements and tests
    I.S. EN 143000:1994 THERMISTORS (GENERIC SPECIFICATION)
    BS EN 61270-1:1998 Capacitors for microwave ovens General
    BS EN 61189-1 : 1997 TEST METHODS FOR ELECTRICAL MATERIALS, INTERCONNECTION STRUCTURES AND ASSEMBLIES - GENERAL TEST METHODS AND METHODOLOGY
    BS IEC 60747-5.2 : 97 AMD 13433 DISCRETE SEMICONDUCTOR DEVICES AND INTEGRATED CIRCUITS - OPTOELECTRONIC DEVICES - ESSENTIAL RATINGS AND CHARACTERISTICS
    11/30252930 DC : 0 BS EN 60747-5-7 - SEMICONDUCTOR DEVICES - DISCRETE DEVICES - PART 5-7: PHOTODIODES AND PHOTOTRANSISTORS
    IEC 61045-1:1991 Fixed film resistor networks for use in electronic equipment - Part 1: Generic specification
    DIN EN 60868 : 1994 FLICKERMETER - FUNCTIONAL AND DESIGN SPECIFICATIONS
    I.S. EN 50491-2:2010 GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 2: ENVIRONMENTAL CONDITIONS
    CEI EN 61270-1 : 1997 CAPACITORS FOR MICROWAVE OVENS - PART 1: GENERAL
    EN 61851-22 : 2002 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - AC ELECTRIC VEHICLE CHARGING STATION
    BS IEC 60780 : 1998 NUCLEAR POWER PLANTS - ELECTRICAL EQUIPMENT OF THE SAFETY SYSTEM - QUALIFICATION
    03/103740 DC : DRAFT FEB 2003 IEC 61337-1 ED.1 - FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    CEI EN 60169-21 : 1998 RADIO-FREQUENCY CONNECTORS - PART 21: TWO TYPES OF RADIO-FREQUENCY CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 9,5 MM (0,374 IN) WITH DIFFERENT VERSIONS OF SCREW COUPLING CHARACTERISTIC IMPEDANCE 50 OHMS (TYPES SC-A AND SC-B)
    11/30252977 DC : 0 BS EN 61747-10-2 - LIQUID CRYSTAL DISPLAY DEVICES - PART 10-2: ENVIRONMENTAL, ENDURANCE AND MECHANICAL TEST METHODS - ENVIRONMENTAL AND ENDURANCE
    BS 123500-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - FLEXIBLE SINGLE-SIDED AND DOUBLE-SIDED PRINTED BOARDS WITH THROUGH-CONNECTIONS
    97/231700 DC : DRAFT DEC 1997 IEC 60115-1 - FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
    BS EN 62326-4-1 : 1997 PRINTED BOARDS - RIGID MULTILAYER PRINTED BOARDS WITH INTERLAYER CONNECTIONS - SECTIONAL SPECIFICATION - CAPABILITY DETAIL SPECIFICATION - PERFORMANCE LEVELS, A, B AND C
    ISO 15003:2006 Agricultural engineering Electrical and electronic equipment Testing resistance to environmental conditions
    11/30205538 DC : 0 BS EN 54-5 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 5: HEAT DETECTORS - POINT DETECTORS
    BS CECC30000(1984) : 1984 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: FIXED CAPACITORS
    BS EN 140000 : 1995 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: FIXED RESISTORS
    03/101947 DC : DRAFT FEB 2003 IEC 60939-1 ED.2.0 - PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    BS EN 169000:1993 Harmonized system of quality assessment for electronic components. Generic specification. Quartz crystal controlled oscillators
    03/114763 DC : DRAFT SEP 2003 EN 54-18 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 18: REQUIREMENTS AND TEST METHODS FOR INPUT/OUTPUT DEVICES FOR USE ON THE TRANSMISSION PATHS OF FIRE DETECTION AND FIRE ALARM SYSTEMS
    I.S. EN 12405:2002 GAS METERS - GAS-VOLUME ELECTRONIC CONVERSION DEVICES
    BS EN 60694 : 1997 COMMON SPECIFICATION FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
    BS 4671(1987) : AMD 7870 METHODS FOR EVALUATING THE PERFORMANCE OF ELECTRICAL AND PNEUMATIC ANALOGUE CHART RECORDERS FOR USE IN INDUSTRIAL PROCESS CONTROL SYSTEMS
    BS EN 60966-1:1999 (published 1999-10) Radio frequency and coaxial cable assemblies Generic specification. General requirements and test methods
    NF EN 50136-2-1 : 98 AMD 1 2002 ALARM SYSTEMS - ALARM TRANSMISSION SYSTEMS AND EQUIPMENT - PART 2-1: GENERAL REQUIREMENTS FOR EQUIPMENT USED IN SYSTEMS USING DEDICATED ALARM PATHS
    BS EN 50132-4-1:2001 ALARM SYSTEMS - CCTV SURVEILLANCE SYSTEMS FOR USE IN SECURITY APPLICATIONS PART 4-1: BLACK AND WHITE MONITORS
    CEI EN 138000 : 1996 GENERIC SPECIFICATION: FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (INDUCTORS FOR WHICH SAFETY TESTS ARE REQUIRED)
    08/30179134 DC : DRAFT MAR 2008 BS EN 60143-4 - SERIES CAPACITORS FOR POWER SYSTEMS - PART 4: THYRISTOR CONTROLLED SERIES CAPACITORS
    BS 123800-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - FLEXIBLE MULTILAYER PRINTED BOARDS WITH THROUGH-CONNECTIONS
    12/30259014 DC : 0 BS EN 60127-6 - MINIATURE FUSES - PART 6: FUSE-HOLDERS FOR MINIATURE FUSE-LINKS
    BS 4584-1(1983) : 1983 AMD 8050 METAL CLAD BASE MATERIALS FOR PRINTED WIRING BOARDS - METHODS OF TEST
    CSA CEI/IEC 61000.4.15 : 2003 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4: TESTING AND MEASUREMENT TECHNIQUES - SECTION 15: FLICKERMETER - FUNCTIONAL AND DESIGN SPECIFICATIONS
    BS EN 61851-22 : 2002 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - AC ELECTRIC VEHICLE CHARGING STATION
    BS EN 60512-11-3:2002 (published 2002-05) Connectors for electronic equipment. Tests and measurements. Climatic tests Test 11c. Damp heat, steady state
    04/30104415 DC : DRAFT AUG 2004 EN 54-20 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 20: ASPIRATING SMOKE DETECTORS
    BS EN 60169-21 : 1997 RADIO-FREQUENCY CONNECTORS - PART 21: TWO TYPES OF RADIO-FREQUENCY CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 9,5 MM (0,374 IN) WITH DIFFERENT VERSIONS OF SCREW COUPLING - CHARACTERISTIC IMPEDANCE 50 OHMS (TYPES SC-A AND SC-B)
    BS ISO 11614 : 1999 RECIPROCATING INTERNAL COMBUSTION COMPRESSION-IGNITION ENGINES - APPARATUS FOR MEASUREMENT OF THE OPACITY AND FOR DETERMINATION OF THE LIGHT ABSORPTION COEFFICIENT OF EXHAUST GAS
    BS CECC 16000-1:1992 Harmonized system of quality assessment for electronic components. Generic specification: electromechanical all-or-nothing relays General
    11/30245197 DC : 0 BS EN 60143-2 - SERIES CAPACITORS FOR POWER SYSTEMS - PART 2: PROTECTIVE EQUIPMENTS FOR SERIES CAPACITOR BANKS
    13/30264596 DC : 0 BS EN 60747-14-7 ED 1.0 - SEMICONDUCTOR DEVICES - PART 14-7: SEMICONDUCTOR SENSORS - FLOW METER
    16/30337159 DC : 0 BS EN ISO 9455-15 - SOFT SOLDERING FLUXES - TEST METHODS - PART 15: COPPER CORROSION TEST
    13/30291609 DC : 0 BS EN 60966-1 - RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND TEST METHODS
    00/201245 DC : DRAFT FEB 2000 IEC 62029-1 - COAXIAL CABLES USED IN CABLED DISTRIBUTION NETWORKS - PART 1: GENERIC SPECIFICATION AND TEST METHODS
    05/30139105 DC : DRAFT SEP 2005 IEC 61800-5-1 ED 2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    03/103741 DC : DRAFT FEB 2003 IEC 61338-1 ED.1 - WAVEGUIDE TYPE DIELECTRIC RESONATORS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    BS 415(1998) : 1998 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    BS EN 61204 : 1995 LOW-VOLTAGE POWER SUPPLY DEVICES, D.C. OUTPUT - PERFORMANCE CHARACTERISTICS
    02/206181 DC : DRAFT MAY 2002 IEC 61019-1. ED.1 - SURFACE ACOUSTIC WAVE RESONATORS (SAW) OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    13/30264600 DC : 0 BS EN 60747-14-8 ED 1.0 - SEMICONDUCTOR DEVICES - PART 14-8: SEMICONDUCTOR SENSORS - CAPACITIVE DEGRADATION SENSOR OF LIQUID
    IEC 61851-22:2001 Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station
    CEI EN 60966-1 : 2001 RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES - PART 1: GENERIC SPECIFICATION GENERAL REQUIREMENTS AND TEST METHODS
    BS EN 61007 : 1997 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - MEASURING METHODS AND TEST PROCEDURES
    BS 123400-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - FLEXIBLE SINGLE-SIDED AND DOUBLE-SIDED PRINTED BOARDS WITHOUT THROUGH-CONNECTIONS
    BS 123700-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - FLEX-RIGID DOUBLE-SIDED PRINTED BOARDS WITH THROUGH-CONNECTIONS
    BS EN 61011 : 1993 ELECTRIC FENCE ENERGIZERS - SAFETY REQUIREMENTS FOR MAINS-OPERATED ELECTRIC FENCE ENERGIZERS
    BS EN 62326-4 : 1997 PRINTED BOARDS - PART 4: RIGID MULTILAYER PRINTED BOARDS WITH INTERLAYER CONNECTIONS - SECTIONAL SPECIFICATION
    BS EN 60252 : 1994 A.C. MOTOR CAPACITORS
    BS EN 171000:2001 Harmonized system of quality assessment for electronic components. Generic specification. Filters using waveguide type dielectric resonators
    03/106843 DC : DRAFT MAY 2003 ISO 7240-6 - FIRE DETECTION AND ALARM SYSTEMS - PART 6: POINT-TYPE FIRE DETECTORS FOR DETECTION OF CARBON MONOXIDE
    04/30122860 DC : DRAFT SEP 2004 ISO 7240-22 - FIRE DETECTION AND FIRE ALARM EQUIPMENT - PART 22: DUCT SAMPLING EQUIPMENT
    BS EN 60749 : 1999 SEMICONDUCTOR DEVICES - MECHANICAL AND CLIMATIC TEST METHODS
    DIN EN 61810-5 : 1999 ELECTROMECHANICAL NON-SPECIFIED TIME ALL-OR-NOTHING RELAYS - PART 5: INSULATION COORDINATION
    NF EN 61291 5-2 : 2003 OPTICAL AMPLIFIERS - PART 5-2: QUALIFICATION SPECIFICATIONS - RELIABILITY QUALIFICATION FOR OPTICAL FIBRE AMPLIFIERS
    NF EN 62326 4-1 : 1998 PRINTED BOARDS - PART 4: RIGID MULTILAYER PRINTED BOARDS WITH INTERLAYER CONNECTIONS - SECTIONAL SPECIFICATION - SECTION 1: CAPABILITY DETAIL SPECIFICATION PERFORMANCE LEVELS A, B AND C
    BS EN 61248-1 : 1997 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - PART 1: GENERIC SPECIFICATION
    DIN IEC 60068-2-20:1991-04 ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TEST T: SOLDERING
    BS IEC 60748-23-1:2002 Semiconductor devices. Integrated circuits. Hybrid integrated circuits and film structures. Manufacturing line certification Generic specification
    CEI EN 60368-1 : 2006 PIEZOELECTRIC FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    OIML R 129 : 2000 MULTI-DIMENSIONAL MEASURING INSTRUMENTS
    I.S. EN 61193-3:2013 QUALITY ASSESSMENT SYSTEMS - PART 3: SELECTION AND USE OF SAMPLING PLANS FOR PRINTED BOARD AND LAMINATE END-PRODUCT AND IN-PROCESS AUDITING (IEC 61193-3:2013 (EQV))
    BS EN 61881 : 2000 RAILWAY APPLICATIONS - ROLLING STOCK EQUIPMENT - CAPACITORS FOR POWER ELECTRONICS
    95/216358 DC : 0 PREN 50228-1 - PERFORMANCE REQUIREMENTS AND TEST METHODS FOR CONTROL AND MONITORING PH ANALYSERS FOR USE IN THE WATER INDUSTRY - PART 1: SPECIFICATION AND TEST METHODS FOR ASSESSING PERFORMANCE UNDER LABORATORY CONDITIONS
    BS 123100-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - RIGID SINGLE-SIDED AND DOUBLE-SIDED PRINTED BOARDS WITH PLAIN HOLES
    02/709474 DC : DRAFT JULY 2002 BS EN 1760-3 - SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE BUMPERS, PLATES, WIRES AND SIMILAR DEVICES
    DIN EN 138000 : 1997 GENERIC SPECIFICATION; FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (INDUCTORS FOR WHICH SAFETY TESTS ARE REQUIRED)
    BS 6796(1986) : 1986 SPECIFICATION FOR FLICKERMETERS
    BS 2011-2.2C&D(1990) : 1990 ENVIRONMENTAL TESTING - TESTS - TESTS C & D - GUIDANCE FOR DAMP HEAT TESTS
    BS EN 61810-5 : 1999 ELECTROMECHANICAL NON-SPECIFIED TIME ALL-OR-NOTHING RELAYS - INSULATION COORDINATION
    I.S. EN 60169-21:1999 RADIO-FREQUENCY CONNECTORS - PART 21: TWO TYPES OF RADIO-FREQUENCY CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 9,5 MM (0,374 IN) WITH DIFFERENT VERSIONS OF SCREW COUPLING - CHARACTERISTIC IMPEDANCE 50 OHMS (TYPES SC-A AND SC-B)
    I.S. EN 60249-1:1994 BASE MATERIALS FOR PRINTED CIRCUITS - PART 1: TEST METHODS
    BS EN 165000-1 : 1996 FILM AND HYBRID INTEGRATED CIRCUITS - GENERIC SPECIFICATION - PART 1: CAPABILITY APPROVAL PROCEDURE
    08/30193715 DC : 0 BS EN 62246-1 ED.2 - REED SWITCHES - PART 1: GENERIC SPECIFICATION
    BS EN 123400 : 1992 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: FLEXIBLE PRINTED BOARDS WITHOUT THROUGH CONNECTIONS
    BS EN 130000 : 1994 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: FIXED CAPACITORS
    BS EN 120000 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERAL SPECIFICATION: SEMICONDUCTOR OPTOELECTRONIC AND LIQUID CRYSTAL DEVICES
    BS QC 763000(1990) : AMD 6754 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS. FILM AND HYBRID FILM INTEGRATED CIRCUITS. GENERIC SPECIFICATION
    ISA S82.01 : 1994 ELECTRICAL AND ELECTRONIC TEST, MEASURING, CONTROLLING AND RELATED EQUIPMENT - GENERAL REQUIREMENTS
    10/30234803 DC : 0 BS EN 61169-1 ED.2 - RADIO FREQUENCY CONNECTORS - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND MEASURING METHODS
    01/714407 DC : DRAFT OCT 2001 ISO/DIS 16750-4 - ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 4: CLIMATIC LOADS
    I.S. EN 61249-8-7:1999 MATERIALS FOR INTERCONNECTION STRUCTURES - PART 8: SECTIONAL SPECIFICATION SET FOR NON-CONDUCTIVE FILMS AND COATINGS - SECTION 7: MARKING LEGEND INKS
    OIML R 125 : 1998 MEASURING SYSTEMS FOR THE MASS OF LIQUIDS IN TANKS
    02/211631 DC : 0 IEC 60747-5-5 ED.1.0 - SEMICONDUCTOR DEVICES - PART 5-5: OPTOELECTRONIC DEVICES - PHOTOCOUPLERS, OPTOCOUPLERS
    BS 2782-5.551A(1988) : 1988 AMD 10820 METHODS OF TESTING PLASTICS - OPTICAL AND COLOUR PROPERTIES, WEATHERING - DETERMINATION OF THE EFFECTS OF EXPOSURE TO DAMP HEAT, WATER SPRAY AND SALT MIST
    13/30268917 DC : 0 BS EN 50290-4-1 ED.2 PREN 50290-4-1 ED.2 - COMMUNICATION CABLES - PART 4-1: GENERAL CONSIDERATIONS FOR THE USE OF CABLES - ENVIRONMENTAL CONDITIONS AND SAFETY ASPECTS
    BS EN 61248-7 : 1998 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATIONS EQUIPMENT - PART 7: SECTIONAL SPECIFICATION FOR HIGH-FREQUENCY INDUCTORS AND INTERMEDIATE TRANSFORMERS ON THE BASIS OF THE CAPABILITY APPROVAL PROCEDURE
    CEI EN 61249-8-7 : 1997 MATERIALS FOR INTERCONNECTION STRUCTURES - PART 8: SECTIONAL SPECIFICATION SET FOR NON-CONDUCTIVE FILMS AND COATINGS - SECTION 7: MARKING LEGEND INKS
    BS CECC17000(1992) : 1992 AMD 9626 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION - SOLID STATE ALL OR NOTHING RELAYS - GENERIC DATA AND METHODS OF TEST
    BS 2011-4.2(1984) : 1984 ENVIRONMENTAL TESTING - MISCELLANEOUS - GUIDANCE ON THE APPLICATION OF THE TESTS OF BS 2011 TO SIMULATE THE EFFECTS OF STORAGE
    BS EN 60122-1 : 2002 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    04/30114936 DC : DRAFT JUN 2004 EN 50439 - RAILWAY APPLICATIONS - RELIABILITY TESTS FOR HIGH POWER SEMICONDUCTORS DEVICES - PART 1: STANDARD BASE-PLATE MODULES
    BS EN 180000 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: FIBRE OPTIC ATTENUATORS
    06/30117299 DC : 0 BS EN 54-15 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 15: POINT DETECTORS USING A COMBINATION OF DETECTED FIRE PHENOMENA
    01/206938 DC : DRAFT OCT 2001 IEC 60255-27 ED.1.0 - MEASURING RELAYS AND EQUIPMENT - PART 27: PRODUCT SAFETY REQUIREMENTS FOR MEASURING RELAYS AND PROTECTION EQUIPMENT
    BS PD6521(1988) : 1988 SUMMARIES OF TEST METHODS FOR ENVIRONMENTAL TESTING OF ELECTROTECHNICAL PRODUCTS
    BS EN 60068-2-48 : 2000
    BS EN 168000:1996 Harmonized system of quality assessment for electronic components. Generic specification: quartz crystal units
    IEC 60326-9:1991 Printed boards - Part 9: Specification for flexible multilayer printed boards with through connections
    CSA E1048 : 1998 CAPACITORS FOR USE IN TUBULAR FLUORESCENT AND OTHER DISCHARGE LAMP CIRCUITS - GENERAL AND SAFETY REQUIREMENTS
    BS EN 61193-3 : 2013 QUALITY ASSESSMENT SYSTEMS - PART 3: SELECTION AND USE OF SAMPLING PLANS FOR PRINTED BOARD AND LAMINATE END-PRODUCT AND IN-PROCESS AUDITING
    CSA E691 : 0 THERMAL LINKS - REQUIREMENTS AND APPLICATION GUIDE
    CEI EN 61851-22 : 2003 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: AC ELECTRIC VEHICLE CHARGING STATION
    BS EN 60835-1-1 : 1994 METHODS OF MEASUREMENT FOR EQUIPMENT USED IN DIGITAL MICROWAVE RADIO TRANSMISSION SYSTEMS - MEASUREMENTS COMMON TO TERRESTRIAL RADIO-RELAY SYSTEMS AND SATELLITE EARTH STATIONS - PART 1-1: GENERAL
    BS CECC30000(1992) : 1992 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS. GENERIC SPECIFICATION: FIXED CAPACITORS
    05/30134428 DC : DRAFT JUN 2005
    02/540596 DC : DRAFT JULY 2002 PREN 54-17 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 17: SHORT CIRCUIT ISOLATORS
    BS 7526(1991) : 1991 AMD 7980 METHODS OF EVALUATING THE PERFORMANCE OF ELECTROMAGNETIC FLOWMETERS
    05/30132097 DC : DRAFT JUNE 2005 IEC 60679-1 ED 3 - QUARTZ CRYSTAL CONTROLLED OSCILLATORS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    02/211632 DC : DRAFT DEC 2002 IEC 69747-5-4 ED.1 - SEMICONDUCTOR DEVICES - DISCRETE DEVICES - PART 5-4: OPTOELECTRONIC DEVICES - SEMICONDUCTOR LASERS
    01/203790 DC : DRAFT JUNE 2001 IEC 62093 ED.1 - BALANCE-OF-SYSTEM COMPONENTS FOR PHOTO-VOLTAIC SYSTEMS - DESIGN QUALIFICATION AND TYPE APPROVAL
    BS EN 50132-2-1 : 1998 ALARM SYSTEMS - CCTV SURVEILLANCE SYSTEMS FOR USE IN SECURITY APPLICATIONS - BLACK AND WHITE CAMERAS
    BS EN 60368-1:2000 Piezoelectric filters Generic specification
    CSA E60127.6 : 2003 : R2012 MINIATURE FUSES - PART 6: FUSE-HOLDERS FOR MINIATURE CARTRIDGE FUSE-LINKS
    BS EN 61243-5 : 2001 LIVE WORKING - VOLTAGE DETECTORS - PART 5: VOLTAGE DETECTING SYSTEMS (VDS)
    BS EN 181000 : 1995 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: FIBRE OPTIC BRANCHING DEVICES
    CSA E60127.6 : 2003 MINIATURE FUSES - PART 6: FUSE-HOLDERS FOR MINIATURE CARTRIDGE FUSE-LINKS
    CAN/CSA-E60127-6-03 (R2017) Miniature Fuses - Part 6: Fuse-Holders for Miniature Cartridge Fuse-Links (Adopted CEI/IEC 127-6:1994, first edition, 1994-04, including Amendment 1:1996, with Canadian deviations) | Coupe-circuit miniatures - Partie 6: Ensembles-porteurs pour cartouches de coupe-circuit miniatures (norme CEI/IEC 127-6:1994 adoptée, première édition, 1994-04, y compris l\'Amendement 1:1996, avec exigences propres au Canada)
    CEI EN 60077-1 : 2002 RAILWAY APPLICATIONS - ELECTRIC EQUIPMENT FOR ROLLING STOCK - PART 1: GENERAL SERVICE CONDITIONS AND GENERAL RULES
    01/205810 DC : DRAFT AUG 2001 IEC 61215 ED.2.0 - CRYSTALLINE SILICON TERRESTRIAL PHOTOVOLTAIC (PV) MODULES - DESIGN QUALIFICATION AND TYPE APPROVAL
    07/30166909 DC : DRAFT AUG 2007 BS EN 15714-2 - INDUSTRIAL VALVES - ACTUATORS - PART 2: ELECTRIC ACTUATORS FOR INDUSTRIAL VALVES - BASIC REQUIREMENTS
    BS CECC68000(1990) : AMD 9184 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: QUARTZ CRYSTAL UNITS
    04/30115471 DC : DRAFT JUL 2004 ISO 7240-21 - FIRE DETECTION AND ALARM SYSTEMS - PART 21: ROUTING EQUIPMENT
    NBR IEC 61851-22 : 2013 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: A.C ELECTRIC VEHICLE CHARGING STATION
    EN 54-7:2000/A2:2006 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 7: SMOKE DETECTORS - POINT DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONIZATION
    BS 123600-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - FLEX-RIGID MULTILAYER PRINTED BOARDS WITH THROUGH-CONNECTIONS
    NF EN 60938-1 : 2008 AMD 1 2008 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    IEC 62326-4:1996 Printed boards - Part 4: Rigid multilayer printed boards with interlayer connections - Sectional specification
    DIN EN 61881 : 2000 RAILWAY APPLICATIONS - ROLLING STOCK EQUIPMENT - CAPACITORS FOR POWER ELECTRONICS
    DIN EN 60252 : 1994 CAPACITORS - MOTOR CAPACITORS
    BS EN 50136-2-1 : 1998 ALARM SYSTEMS - ALARM TRANSMISSION SYSTEMS AND EQUIPMENT - PART 2-1: GENERAL REQUIREMENTS FOR ALARM TRANSMISSION EQUIPMENT
    IEC 61338-1-2:1998 Waveguide type dielectric resonators - Part 1-2: General information and test conditions - Test conditions
    GOST R IEC 60252-1 : 2005 AC MOTOR CAPACITORS - PART 1: GENERAL. PERFORMANCE, TESTING AND RATING - SAFETY REQUIREMENTS - GUIDE FOR INSTALLATION AND OPERATION
    ISO 3930:2000 Instruments for measuring vehicle exhaust emissions
    I.S. EN 168000:1994 QUARTZ CRYSTAL UNITS (GENERIC SPECIFICATION)
    I.S. EN 181000:1994 FIBRE OPTIC BRANCHING DEVICES (GENERIC SPECIFICATION)
    NF ISO 3930 : 2001 INSTRUMENTS FOR MEASURING VEHICLE EXHAUST EMISSIONS
    BS EN 167000:1993 Harmonized system of quality assessment for electronic components. Generic specification: piezoelectric filters
    BS EN 138000 : 1997 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (INDUCTORS FOR WHICH SAFETY TESTS ARE REQUIRED)
    BS ISO 15003:2006 AGRICULTURAL ENGINEERING - ELECTRICAL AND ELECTRONIC EQUIPMENT - TESTING RESISTANCE TO ENVIRONMENTAL CONDITIONS
    I.S. EN 16602-70-10:2015 SPACE PRODUCT ASSURANCE - QUALIFICATION OF PRINTED CIRCUIT BOARDS
    I.S. EN 60694:1999 COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
    NF EN 61249 8-7 : 1997 MATERIALS FOR INTERCONNECTION STRUCTURES - PART 8: SECTIONAL SPECIFICATION SET FOR NON CONDUCTIVE FILMS AND COATINGS - SECTION 7: MARKING LEGEND LINKS
    I.S. EN 61007:1998 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - MEASURING METHODS AND TEST PROCEDURES
    CEI EN 60068-2-52 : 1997 ENVIRONMENTAL TESTING - PART 2: TESTS - TEST KB: SALT MIST, CYCLIC (SODIUM CHLORIDE SOLUTION)
    CEI EN 60068-2-48 : 2000 ENVIRONMENTAL TESTING - PART 2: TESTS - GUIDANCE ON THE APPLICATION OF THE TESTS OF IEC PUBLICATION 60068 TO SIMULATE THE EFFECTS OF STORAGE
    I.S. EN 60835-1-1:1993 METHODS OF MEASUREMENT FOR EQUIPMENT USED IN DIGITAL MICROWAVE RADIO TRANSMISSION SYSTEMS - PART 1: MEASUREMENTS COMMON TO TERRESTRIAL RADIO-RELAY SYSTEMS AND SATELLITE EARTH STATIONS - SECTION ONE: GENERAL
    I.S. EN 60122-1:2002 AMD 1 2018 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    I.S. EN 61270-1:1999 CAPACITORS FOR MICROWAVE OVENS - PART 1: GENERAL
    NBR ISO 9104 : 2000 MEDICAO DE VAZAO DE FLUIDOS EM CONDUTOS FECHADOS - METODOS PARA AVALIACAO DE DESEMPENHO DE MEDIDORES DE VAZAO ELETROMAGNETICOS PARA LIQUIDOS
    I.S. EN 165000-1:1998 FILM AND HYBRID INTEGRATED CIRCUITS - PART 1: GENERIC SPECIFICATION CAPABILITY APPROVAL PROCEDURE
    I.S. EN 138000:1998 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (INDUCTORS FOR WHICH SAFETY TESTS ARE REQUIRED) (GENERIC SPECIFICATION)
    I.S. EN 54-7:2000 COMPONENTS OF AUTOMATIC FIRE DETECTION SYSTEMS - POINT-TYPE SMOKE DETECTORS - DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONIZATION
    BS EN 54-7:2001 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 7: SMOKE DETECTORS - POINT DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONIZATION
    NF EN 61249 5-4 : 1997 MATERIALS FOR INTERCONNECTION STRUCTURES - PART 5: SECTIONAL SPECIFICATION SET FOR CONDUCTIVE FOILS AND FILMS WITH OR WITHOUT COATINGS - SECTION 4: CONDUCTIVE INKS
    NF EN 50132-2-1 : 1997 ALARM SYSTEMS - CCTV SURVEILLANCE SYSTEMS FOR USE IN SECURITY APPLICATIONS - PART 2-1: BLACK AND WHITE CAMERAS
    IEC 61178-1:1993 Quartz crystal units - A specification in the IEC Quality Assessment System for Electronic Components (IECQ) - Part 1: Generic specification
    I.S. CECC 33000:1994 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (GENERIC SPECIFICATION)
    I.S. EN 133000:1998 PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (GENERIC SPECIFICATION)
    I.S. EN 61249-5-4:1999 MATERIALS FOR INTERCONNECTION STRUCTURES - PART 5: SECTIONAL SPECIFICATION SET FOR CONDUCTIVE FOILS AND FILMS WITH OR WITHOUT COATINGS - SECTION 4: CONDUCTIVE INKS
    XP X08 150 : 2007 XP INFORMATION AND SAFETY DEVICES - WIRELESS RISK INFORMATION SYSTEM (IRIS.RADIO)
    I.S. EN 61248-1:1998 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - PART 1: GENERIC SPECIFICATION
    NF EN 60835 1-1 : 1993 METHODS OF MEASUREMENT FOR EQUIPMENT USED IN DIGITAL MICROWAVE RADIO TRANSMISSION SYSTEMS - PART 1: MEASUREMENTS COMMON TO TERRESTRIAL RADIO-RELAY SYSTEMS AND SATELLITE EARTH STATIONS - SECTION ONE: GENERAL
    ONORM EN 54-7 : 2006 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 7: SMOKE DETECTORS - POINT DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONIZATION
    BS 2011-2.1CB(1990) : 1990 ENVIRONMENTAL TESTING - TESTS - TEST Cb: DAMP HEAT, STEADY STATE, PRIMARILY FOR EQUIPMENT
    NF EN 61851-22 : 2002 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: A.C. ELECTRIC VEHICLE CHARGING STATION
    IEC 61253-1:1993 Piezoelectric ceramic resonators - A specification in the IEC quality assessment system for electronic components (IECQ) - Part 1: Generic specification - Qualification approval
    BIS IS 15934-5 : 2011 LIQUID CRYSTAL AND SOLID-STATE DISPLAY DEVICES - PART 5: ENVIRONMENTAL, ENDURANCE AND MECHANICAL TEST METHODS
    GOST EN 1760-1 : 2004 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1 - GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
    NF EN 60068 2-48 : 2000 ENVIRONMENTAL TESTING - PART 2: TESTS - GUIDANCE ON THE APPLICATION OF THE TEST OF IEC 60068 TO SIMULATE THE EFFECTS OF STORAGE
    NBR IEC 62326-4-1 : 2007 ERRATA 2007 PRINTED BOARDS - PART 4: RIGID MULTILAYER PRINTED BOARDS WITH INTERLAYER CONNECTIONS - SECTIONAL SPECIFICATION SECTION 1: CAPABILITY DETAIL SPECIFICATION - PERFORMANCE LEVELS A, B AND C
    CEI EN 60747-5-2 : 2002 DISCRETE SEMICONDUCTOR DEVICES AND INTEGRATED CIRCUITS - PART 5-2: OPTOELECTRONIC DEVICES - ESSENTIAL RATINGS AND CHARACTERISTICS
    NFS 61 023 : 2004 XP FIRE DETECTION SYSTEMS (FDS) USING RADIO LINKS
    NF EN 50132-4-1 : 2002 ALARM SYSTEMS - CCTV SURVEILLANCE SYSTEMS FOR USE IN SECURITY APPLICATIONS - PART 4-1: BLACK AND WHITE MONITORS
    I.S. EN 60368-1:2000 PIEZOELECTRIC FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    ISO 10546:1993 Chemical conversion coatings Rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys
    I.S. EN 61248-7:1998 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - PART 7: SECTIONAL SPECIFICATION FOR HIGH-FREQUENCY INDUCTORS AND INTERMEDIATE FREQUENCY TRANSFORMERS ON THE BASIS OF THE CAPABILITY APPROVAL PROCEDURE
    IEC 60249-3-3:1991 Base materials for printed circuits - Part 3: Special materials used in connection with printed circuits - Specification No. 3: Permanent polymer coating materials (solder resist) for use in the fabrication of printed boards
    BS 7825-3.5:1997 CALIBRATION OF RUBBER AND PLASTICS TEST EQUIPMENT - CALIBRATION SCHEDULES - OPTICAL AND WEATHERING PROPERTIES
    BS CECC 43000(1982) : AMD 7315 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: DIRECTLY HEATED NEGATIVE TEMPERATURE COEFFICIENT THERMISTORS
    BS EN 60938-1 : 2000 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    I.S. EN 134000:1994 GENERIC SPECIFICATION: VARIABLE CAPACITORS (QUALIFICATION APPROVAL AND CAPABILITY APPROVAL)
    CEI EN 60122-1 : 2004 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    IEC 60748-23-1:2002 Semiconductor devices - Integrated circuits - Part 23-1: Hybrid integrated circuits and film structures - Manufacturing line certification - Generic specification
    I.S. EN 60512-11-3:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-3: CLIMATIC TESTS - TEST 11C: DAMP HEAT, STEADY STATE
    IEC 60300-3-5:2001 Dependability management - Part 3-5: Application guide - Reliability test conditions and statistical test principles
    IEC 61019-1-2:1993 Surface acoustic wave (SAW) resonators - Part 1: General information, standard values and test conditions - Section 2: Test conditions
    I.S. CECC 86000:1993 CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - PART 1: REQUIREMENTS, TEST METHODS AND QUALIFICATION APPROVAL PROCEDURES (GENERIC SPECIFICATION)
    I.S. EN 116000-3:1998 GENERIC SPECIFICATION: ELECTROMECHANICAL ALL-OR-NOTHING RELAYS - PART 3: TEST AND MEASUREMENT PROCEDURES
    IEC 61204:1993+AMD1:2001 CSV Low-voltage power supply devices, d.c. output - Performance characteristics
    IEC 61810-5:1998 Electromechanical non-specified time all-or-nothing relays - Part 5: Insulation coordination
    IEC 61337-1-2:1999 Filters using waveguide type dielectric resonators - Part 1-2: Test conditions
    IEC 60326-10:1991 Printed boards - Part 10: Specification for flex-rigid double-sided printed boards with through connections
    IEC 60326-11:1991 Printed boards - Part 11: Specification for flex-rigid multilayer printed boards with through connections
    IEC 61007:1994 Transformers and inductors for use in electronic and telecommunication equipment - Measuring methods and test procedures
    IEC 62326-4-1:1996 Printed boards - Part 4: Rigid multilayer printed boards with interlayer connections - Sectional specification - Section 1: Capability detail specification - Performance levels A, B and C
    IEC 62103:2003 Electronic equipment for use in power installations
    I.S. EN 60938-1:1999 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    IEC 60780:1998 Nuclear power plants - Electrical equipment of the safety system - Qualification
    I.S. EN 61189-1:1999 TEST METHODS FOR ELECTRICAL MATERIALS, INTERCONNECTION STRUCTURES AND ASSEMBLIES - PART 1: GENERAL TEST METHODS AND METHODOLOGY
    I.S. EN 61204:1996 LOW-VOLTAGE POWER SUPPLY DEVICES, D.C. OUTPUT - PERFORMANCE CHARACTERISTICS
    I.S. EN 61747-5:1999 LIQUID CRYSTAL AND SOLID-STATE DISPLAY DEVICES - PART 5: ENVIRONMENTAL, ENDURANCE AND MECHANICAL TEST METHODS
    IEC 61261-1:1994 Piezoelectric ceramic filters for use in electronic equipment - A specification in the IEC quality assessment system for electronic components (IECQ) - Part 1: Generic specification - Qualification approval
    EN 60938-1:1999/A1:2007 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION - PART 1: GENERIC SPECIFICATION
    EN 54-4:1997/A2:2006 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 4: POWER SUPPLY EQUIPMENT
    NF EN 60122-1 : 2003 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    DIN EN 1760-2:2009-08 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE EDGES AND PRESSURE SENSITIVE BARS
    DIN EN 1760-1:2009-08 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
    UNE-EN 50491-2:2011 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) -- Part 2: Environmental conditions
    BS EN 16602-70-10 : 2015 SPACE PRODUCT ASSURANCE - QUALIFICATION OF PRINTED CIRCUIT BOARDS
    BS EN 45501:2015 METROLOGICAL ASPECTS OF NON-AUTOMATIC WEIGHING INSTRUMENTS
    IEC 61747-5:1998 Liquid crystal and solid-state display devices - Part 5: Environmental, endurance and mechanical test methods
    BS EN 54-4 : 1998 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 4: POWER SUPPLY EQUIPMENT
    IEC 61881:1999 Railway applications - Rolling stock equipment - Capacitors for power electronics
    IEC 60938-1:1999+AMD1:2006 CSV Fixed inductors for electromagnetic interference suppression - Part 1: Generic specification
    BS 123200-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - RIGID DOUBLE-SIDED PRINTED BOARDS WITH PLATED-THROUGH HOLES
    IEC 60368-1:2000+AMD1:2004 CSV Piezoelectric filters of assessed quality - Part 1: Genericspecification
    IEC 61249-8-7:1996 Materials for interconnection structures - Part 8: Sectional specification set for non-conductive films and coatings - Section 7: Marking legend inks
    BS EN 29104 : 1993 MEASUREMENT OF FLUID FLOW IN CLOSED CONDUITS - METHODS OF EVALUATING THE PERFORMANCE OF ELECTROMAGNETIC FLOW-METERS FOR LIQUIDS
    IEC 60749:1996+AMD1:2000+AMD2:2001 CSV Semiconductor devices - Mechanical and climatic test methods
    IEC 60873:1986 Methods of evaluating the performance of electrical and pneumatic analogue chart recorders for use in industrial-process control systems
    IEC 60835-1-1:1990 Methods of measurement for equipment used in digital microwave radio transmission systems. Part 1: Measurements common to terrestrial radio-relay systems and satellite earth stations - Section One: General
    IEC 61249-5-4:1996 Materials for interconnection structures - Part 5: Sectional specification set for conductive foils and films with or without coatings - Section 4: Conductive inks
    BS EN 50090-2-2 : 1997 HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) - PART 2-2: SYSTEM OVERVIEW - GENERAL TECHNICAL REQUIREMENTS
    IEC 61243-5:1997 Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS)
    BS 123300-003(2001) : 2001 SYSTEM OF QUALITY ASSESSMENT - CAPABILITY DETAIL SPECIFICATION - RIGID MULTILAYER PRINTED BOARDS
    00/246907 DC : DRAFT DEC 2000 BS EN 61980-1 - ELECTRICAL - ELECTRIC VEHICLE INDUCTIVE CHARGING SYSTEMS - PART 1: GENERAL REQUIREMENTS
    IEC 61270-1:1996 Capacitors for microwave ovens - Part 1: General
    IEC 60512-11-3:2002 Connectors for electronic equipment - Tests and measurements - Part 11-3: Climatic tests - Test 11c: Damp heat, steady state
    IEC 60966-1:1999 Radio frequency and coaxial cable assemblies - Part 1: Generic specification - General requirements and test methods
    IEC 61747-1:1998+AMD1:2003 CSV Liquid crystal and solid-state display devices - Part 1: Generic specification
    IEC 61193-3:2013 Quality assessment systems - Part 3: Selection and use of sampling plans for printed board and laminate end-product and in-process auditing
    BS EN 54-2 : 1998 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 2: CONTROL AND INDICATING EQUIPMENT
    IEC 61248-1:1996 Transformers and inductors for use in electronic and telecommunication equipment - Part 1: Generic specification
    ISO 13137:2013 Workplace atmospheres — Pumps for personal sampling of chemical and biological agents — Requirements and test methods
    BS EN 1760-2 : 2001 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE EDGES AND PRESSURE SENSITIVE BARS
    BS EN 54-11 : 2001 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 11: MANUAL CALL POINTS
    BS EN 12405 : 2002 GAS METERS - GAS-VOLUME ELECTRONIC CONVERSION DEVICES
    BS EN 50491-2 : 2010 GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 2: ENVIRONMENTAL CONDITIONS
    BS 7822-1:1995 Insulation coordination for equipment within low-voltage systems Principles, requirements and tests
    BS EN 1760-1 : 1998 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
    98/203095 DC : DRAFT JULY 1998 PRENV 50275-2-3 - CONDUCTIVE CHARGING FOR ELECTRIC VEHICLES - PART 2-3: D.C. CHARGING STATION
    IEC 60747-5-2:1997+AMD1:2002 CSV Discrete semiconductor devices and integrated circuits - Part 5-2: Optoelectronic devices - Essential ratings and characteristics
    IEC 61189-1:1997+AMD1:2001 CSV Test methods for electrical materials, interconnection structures and assemblies - Part 1: General test methods and methodology
    EN 61007:1997 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - MEASURING METHODS AND TEST PROCEDURES
    VDS 2116 : 2008 JUNCTION BOXES - REQUIREMENTS
    DIN EN 1760-1:1997-09 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
    I.S. EN 45501:2015 METROLOGICAL ASPECTS OF NON-AUTOMATIC WEIGHING INSTRUMENTS
    DIN EN 12405:2003-10 GAS METERS - GAS-VOLUME ELECTRONIC CONVERSION DEVICES
    DIN EN 1760-2:2001-07 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE EDGES AND PRESSURE SENSITIVE BARS
    EN 60747-5-2:2001/A1:2002 DISCRETE SEMICONDUCTOR DEVICES AND INTEGRATED CIRCUITS - PART 5-2: OPTOELECTRONIC DEVICES - ESSENTIAL RATINGS AND CHARACTERISTICS
    EN 60694:1996/A2:2001 COMMON SPECIFICATIONS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR STANDARDS
    EN 61249-8-7 : 1996 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-46: Measurement - Bore diameter for guide pin in MT ferrules
    EN 61249-5-4 : 1996 MATERIALS FOR INTERCONNECTION STRUCTURES - PART 5: SECTIONAL SPECIFICATION SET FOR CONDUCTIVE FOILS AND FILMS WITH OR WITHOUT COATINGS - SECTION 4: CONDUCTIVE LINKS
    EN 134000 : 1994 GENERIC SPECIFICATION: VARIABLE CAPACITORS (QUALIFICATION APPROVAL AND CAPABILITY APPROVAL)
    EN 60835-1-1 : 1992 Methods of measurement for equipment used in digital microwave radio transmission systems - Part 1: Measurements common to terrestrial radio-relay systems and satellite earth stations - Section 1: General
    EN 12405 : 2002 GAS METERS - GAS-VOLUME ELECTRONIC CONVERSION DEVICES
    EN 61747-5 : 1998 LIQUID CRYSTAL AND SOLID-STATE DISPLAY DEVICES - PART 5: ENVIRONMENTAL, ENDURANCE AND MECHANICAL TEST METHODS
    EN 129000:1993/A1:1995 GENERIC SPECIFICATION - FIXED RF WOUND INDUCTORS
    EN 61011:1992/A11:1996 ELECTRIC FENCE ENERGIZERS - SAFETY REQUIREMENTS FOR MAINS-OPERATED ELECTRIC FENCE ENERGIZERS
    EN 62326-4-1 : 1997 PRINTED BOARDS - RIGID MULTILAYER PRINTED BOARDS WITH INTERLAYER CONNECTIONS - SECTIONAL SPECIFICATION: CAPABILITY DETAIL SPECIFICATION PERFORMANCE LEVELS A, B AND C
    EN 60966-1:1999 RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES - PART 1: GENERIC SPECIFICATION - GENERAL REQUIREMENTS AND TEST METHODS
    EN 61189-1 : 97 AMD 1 2001 TEST METHODS FOR ELECTRICAL MATERIALS, INTERCONNECTION STRUCTURES AND ASSEMBLIES - PART 1: GENERAL TEST METHODS AND METHODOLOGY
    EN 60169-21 : 1997 RADIO-FREQUENCY CONNECTORS - PART 21: TWO TYPES OF RADIO-FREQUENCY CONNECTORS WITH INNER DIAMETER OF OUTER CONDUCTOR 9,5 MM (0,374 IN) WITH DIFFERENT VERSIONS OF SCREW COUPLING - CHARACTERISTIC IMPEDANCE 50 OHMS (TYPES SC-A AND SC-B)
    EN 61193-3 : 2013 QUALITY ASSESSMENT SYSTEMS - PART 3: SELECTION AND USE OF SAMPLING PLANS FOR PRINTED BOARD AND LAMINATE END-PRODUCT AND IN-PROCESS AUDITING (IEC 61193-3:2013)
    EN 61248-7 : 1997 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT - PART 7: SECTIONAL SPECIFICATION FOR HIGH-FREQUENCY INDUCTORS AND INTERMEDIATE FREQUENCY TRANSFORMERS ON THE BASIS OF THE CAPABILITY APPROVAL PROCEDURE
    EN 61243-5 : 2001 LIVE WORKING - VOLTAGE DETECTORS - VOLTAGE DETECTING SYSTEMS (VDS)
    EN 61810-5 : 1998 ELECTROMECHANICAL NON-SPECIFIED TIME ALL-OR-NOTHING RELAYS - INSULATION COORDINATION
    EN 61881 : 1999 RAILWAY APPLICATIONS - ROLLING STOCK EQUIPMENT - CAPACITORS FOR POWER ELECTRONICS
    EN 61270-1 : 1996 CAPACITORS FOR MICROWAVE OVENS - PART 1: GENERAL
    EN 119000 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS: GENERIC SPECIFICATION: DRY AND MERCURY WETTED REED CONTACT UNITS
    EN 60252 : 94 AC 94 A.C. MOTOR CAPACITORS
    EN 61248-1 : 1997 Transformers and inductors for use in electronic and telecommunication equipment - Part 1: Generic specification
    EN 60122-1:2002/A1:2018 QUARTZ CRYSTAL UNITS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION (IEC 60122-1:2002/A1:2017)
    EN 50090-2-2:1996/A2:2007 HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) - PART 2-2: SYSTEM OVERVIEW - GENERAL TECHNICAL REQUIREMENTS
    EN 60491 : 1995 SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
    EN 60368-1:2000/A1:2004 PIEZOELECTRIC FILTERS OF ASSESSED QUALITY - PART 1: GENERIC SPECIFICATION
    EN 50132-4-1 : 2001 ALARM SYSTEMS - CCTV SURVEILLANCE SYSTEMS FOR USE IN SECURITY APPLICATIONS - PART 4-1: BLACK AND WHITE MONITORS
    EN 165000-1:1996 Film and hybrid integrated circuits - Part 1: Generic specification - Capability approval procedure
    EN 60512-11-3 : 2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 11-3: CLIMATIC TESTS - TEST 11C: DAMP HEAT, STEADY STATE
    EN 143000 : 1991 THERMISTORS (GENERIC SPECIFICATION)
    EN 50491-2 : 2010 AMD 1 2015 GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 2: ENVIRONMENTAL CONDITIONS
    EN 116000-3 : 1996 GENERIC SPECIFICATION: ELECTROMECHANICAL ALL-OR-NOTHING RELAYS - PART 3: TEST AND MEASUREMENT PROCEDURES
    EN 137000 : 1995 GENERIC SPECIFICATION: FIXED ALUMINIUM ELECTROLYTIC A.C. CAPACITORS WITH NON-SOLID ELECTROLYTE FOR USE WITH MOTORS
    EN 45501 : 2015 METROLOGICAL ASPECTS OF NON-AUTOMATIC WEIGHING INSTRUMENTS
    EN 50132-2-1 : 1997 ALARM SYSTEMS - CCTV SURVEILLANCE SYSTEMS FOR USE IN SECURITY APPLICATIONS - BLACK AND WHITE CAMERAS
    EN 61204:1995/A1:2001 LOW-VOLTAGE POWER SUPPLY DEVICES, D.C. OUTPUT - PERFORMANCE CHARACTERISTICS (IEC 61204:1993, MODIFIED + A1:2001)
    DIN VDE 0110-1 : 1997 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    EN 60749 : 99 AMD 2 2001 SEMICONDUCTOR DEVICES - MECHANICAL AND CLIMATIC TEST METHODS
    EN 140000 : 1993 GENERIC SPECIFICATION: FIXED RESISTORS
    EN 62326-4 : 1997 PRINTED BOARDS - RIGID MULTILAYER PRINTED BOARDS WITH INTERLAYER CONNECTIONS - SECTIONAL SPECIFICATION
    EN 180000 : 1995 GENERIC SPECIFICATION: FIBRE OPTIC ATTENUATORS
    EN 1760-2:2001+A1:2009 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE EDGES AND PRESSURE SENSITIVE BARS
    EN 54-2:1997/A1:2006 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 2: CONTROL AND INDICATING EQUIPMENT
    EN 16602-70-10 : 2015 SPACE PRODUCT ASSURANCE - QUALIFICATION OF PRINTED CIRCUIT BOARDS
    EN 1760-1:1997+A1:2009 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
    EN 54-11:2001/A1:2005 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 11: MANUAL CALL POINTS
    EN 29104 : 1993 MEASUREMENT OF FLUID FLOW IN CLOSED CONDUITS - METHODS OF EVALUATING THE PERFORMANCE OF ELECTROMAGNETIC FLOW-METERS FOR LIQUIDS
    EN 50136-2-1 : 98 AMD 1 2001 ALARM SYSTEMS - ALARM TRANSMISSION SYSTEMS AND EQUIPMENT - PART 2-1: GENERAL REQUIREMENTS FOR ALARM TRANSMISSION EQUIPMENT
    UNI EN 1760-2 : 2009 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE EDGES AND PRESSURE SENSITIVE BARS
    EN 60249-1 : 1993 COR 1994 BASE MATERIALS FOR PRINTED CIRCUITS - PART 1: TEST METHODS
    UNI EN 1760-1 : 2009 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 1: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE MATS AND PRESSURE SENSITIVE FLOORS
    VDE 0882 : 1996 SAFETY REQUIREMENTS FOR ELECTRONIC FLASH APPARATUS FOR PHOTOGRAPHIC PURPOSES
    CEI EN 61243-5 : 2002 LIVE WORKING - VOLTAGE DETECTORS - PART 5: VOLTAGE DETECTING SYSTEMS (VDS)
    EN 45501:2015 METROLOGICAL ASPECTS OF NON-AUTOMATIC WEIGHING INSTRUMENTS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-2-28:1990 Environmental testing - Part 2: Tests. Guidance for damp heat tests
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective