• IEC 60317-13:2010

    Current The latest, up-to-date edition.

    Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  English - French, Spanish, Castilian

    Published date:  18-03-2010

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions and general notes on methods of
       test and appearance
    4 Dimensions
    5 Electrical resistance
    6 Elongation
    7 Springiness
    8 Flexibility and adherence
    9 Heat shock
    10 Cut-through
    11 Resistance to abrasion (nominal conductor diameters
       from 0,250 mm up to and including 2,500 mm)
    12 Resistance to solvents
    13 Breakdown voltage
    14 Continuity of insulation
    15 Temperature index
    16 Resistance to refrigerants
    17 Solderability
    18 Heat or solvent bonding
    19 Dielectric dissipation factor
    20 Resistance to transformer oil
    21 Loss of mass
    23 Pin hole test
    30 Packaging

    Abstract - (Show below) - (Hide below)

    IEC 60317-13:2010 specifies the requirements of enamelled round copper winding wire of class 200 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide-imide resin. The main changes with respect to the previous edition are:
    - new requirements for appearance;
    - reference to new resistance to refrigerants test in IEC 60851-4;
    - deletion of high temperature failure requirement;
    - new pin hole test requirements.

    This publication is to be read in conjunction with IEC 60317-0-1:2008.

    General Product Information - (Show below) - (Hide below)

    Committee TC 55
    Development Note To be read in conjunction with IEC 60317-0-1. (03/2010) Also numbered as BIS IS 13730-13. (02/2015) Stability Date: 2019. (09/2017)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    02/208319 DC : DRAFT SEP 2002 IEC 60455-3-5 ED.3 - RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 5: UNSATURATED POLYESTER BASED IMPREGNATING RESINS
    BS EN 60317-48 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 48: GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 155
    BS EN 60455-3-5:2006 Resin based reactive compounds used for electrical insulation Specifications for individual materials - Unsaturated polyester based impregnating resins
    BS EN 60464-3-2:2002 Varnishes used for electrical insulation Requirements for hot curing impregnating varnishes
    I.S. EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    CEI EN 60317-50 : 2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 50: GLASS-FIBRE WOUND SILICONE RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 200
    EN IEC 60079-7:2015/A1:2018 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017)
    EN 60464-3-2:2001/A1:2006 VARNISHES USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: HOT CURING IMPREGNATING VARNISHES
    EN 60455-3-5:2006 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 5: UNSATURATED POLYESTER BASED IMPREGNATING RESINS
    11/30247695 DC : 0 BS EN 60317-49 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 49: GLASS-FIBRE WOUND HIGH TEMPERATURE RESIN OR VARNISH - IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 180
    I.S. EN 60464-3-2:2001 VARNISHES USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: HOT CURING IMPREGNATING VARNISHES
    NF EN 60455 3-5 : 2006 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 5: UNSATURATED POLYESTER BASED IMPREGNATING RESINS
    I.S. EN 60317-48:2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 48: GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 155 (IEC 60317-48:2012 (EQV))
    IEC 60079-7:2015+AMD1:2017 CSV Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
    I.S. EN 60079-11:2012 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY 'I'
    ISA 60079-7 : 2008 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY "E"
    BIS IS/IEC 60079-11 : 2006 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY 'I'
    NF EN 61858 : 2009 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    BS EN 60079-7 : 2015 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015)
    11/30247523 DC : DRAFT MAY 2011 BS EN 60317-50 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 50: GLASS-FIBRE WOUND SILICONE RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 200
    12/30273916 DC : 0 BS EN 61858-1 - ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED EIS - PART-1: WIRE-WOUND WINDING EIS
    NF EN 60464 3-2 : 2002 AMD 1 2006 VARNISHES USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: HOT CURING IMPREGNATING VARNISHES
    14/30278882 DC : 0 BS EN 60079-7 IEC 60079-7 ED. 5.0 - EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    BS EN 61858-1 : 2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS
    BS 6811-3.0(1993) : 1993 AMD 8984 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ROUND COPPER WINDING WIRES - GENERAL REQUIREMENTS
    04/30113660 DC : DRAFT MAY 2004 IEC 60079-7 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 7: INCREASED SAFETY 'E'
    BS EN 61858 : 2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    CSA C22.2 No. 60079-7 : 2016 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    I.S. EN 60317-50:2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 50: GLASS-FIBRE WOUND SILICONE RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 200 (IEC 60317-50:2012 (EQV))
    I.S. EN 60079-7:2015 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    CEI EN 60317-48 : 2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 48: GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 155
    IEC 60317-48:2012 Specifications for particular types of winding wires - Part 48: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155
    IEC 60079-11:2011 RLV Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    IEC 60079-11 REDLINE : 6.0 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY 'I'
    UNE-EN 60079-11:2013 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    I.S. EN 60455-3-5:2006 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 5: UNSATURATED POLYESTER BASED IMPREGNATING RESINS
    I.S. EN 61858-1:2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS
    IEC 60079-11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    IEC 60034-18-22:2000 Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions
    BS EN 60079-11:2012 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY 'I'
    08/30175787 DC : DRAFT JAN 2008 BS EN 60079-11 - EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY "I"
    IEC 60317-50:2012 Specifications for particular types of winding wires - Part 50: Glass-fibre wound silicone resin or varnish impregnated, bare or enamelled round copper wire, temperature index 200
    IEC 61858-1:2014 Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS
    IEC 60455-3-5:2006 Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials - Sheet 5: Unsaturated polyester based impregnating resins
    UNE-EN 60317-50:2013 Specifications for particular types of winding wires - Part 50: Glass-fibre wound silicone resin or varnish impregnated, bare or enamelled round copper wire, temperature index 200
    UNE-EN 60317-48:2013 Specifications for particular types of winding wires - Part 48: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155
    BS EN 60317-50 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 50: GLASS-FIBRE WOUND SILICONE RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 200
    CSA E60079.7 : 2003 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 7: INCREASED SAFETY "E"
    BIS IS/IEC 60079-7 : 2006 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
    CEI EN 60455-3-5 : 2006 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 5: UNSATURATED POLYESTER BASED IMPREGNATING RESINS
    CSA C22.2 No. 60079-11 : 2014 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY 'I'
    IEC 61858:2008 Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS
    IEC 60464-3-2:2001+AMD1:2006 CSV Varnishes used for electrical insulation - Part 3: Specificationsfor individual materials - Sheet 2: Hot curing impregnating varnishes
    EN 61858-1 : 2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS
    EN 60317-48 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 48: GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 155 (IEC 60317-48:2012)
    EN 60317-50 : 2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 50: GLASS-FIBRE WOUND SILICONE RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 200
    EN 60079-11:2012 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY "I" (IEC 60079-11:2011)
    EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60317-0-1:2013 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
    IEC 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective