Skip to content
Please enter a keyword to search

  • IEC 60317-16:1990

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

    Specifications for particular types of winding wires. Part 16: Polyester enamelled rectangular copper wire, class 155

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Withdrawn date:  09-01-2012

    Language(s): 

    Published date:  15-10-1990

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Definitions and general notes on methods of test
       and appearance
    4 Dimensions
    5 Electrical resistance
    6 Elongation
    7 Springiness
    8 Flexibility and adherence
    9 Heat shock
    10 Cut-through
    11 Resistance to abrasion
    12 Resistance to solvents
    13 Breakdown voltage
    14 Continuity of insulation
    15 Temperature index
    16 Resistance to refrigerants
    17 Solderability
    18 Heat or solvent bonding
    19 Dielectric dissipation factor
    20 Resistance to transformer oil
    21 Loss of mass
    22 High temperature failure
    23 Pin hole test
    30 Packaging
    Annex ZA (normative) Other international publications
             quoted in this standard with the references
             of the relevant European publications
    National annex NA (informative) Cross-reference

    Abstract - (Show below) - (Hide below)

    Describes the requirements of enamelled rectangular copper winding wires of class 155 with a sole coating based on polyester resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements.

    General Product Information - (Show below) - (Hide below)

    Committee TC 55
    Development Note Also numbered as BS EN 60317-16. (10/2005)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Withdrawn
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BIS IS 13730-32 : 1997 AMD 1 2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 32: GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED RECTANGULAR COPPER WIRE, TEMPERATURE INDEX 155
    BS EN 61858-2:2014 Electrical insulation systems. Thermal evaluation of modifications to an established electrical insulation system (EIS) Form-wound EIS
    I.S. EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    EN 61858-2:2014 Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 2: Form-wound EIS
    12/30273912 DC : 0 BS EN 61858-2 - ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED EIS - PART-2: FORM-WOUND EIS
    10/30206053 DC : 0 BS EN 60317-61 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 61: POLYESTER GLASS FIBRE WOUND, IMPREGNATED OR NOT IMPREGNATED, BARE, GRADE 1 OR GRADE 2 ENAMELLED RECTANGULAR COPPER WINDING WIRE WITH TEMPERATURE INDEX 180
    BIS IS 13730-31 : 1997 AMD 1 2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 31: GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED RECTANGULAR COPPER WIRE, TEMPERATURE INDEX 180
    NF EN 61858 : 2009 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    BS EN 61858:2008 Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS
    I.S. EN 61858-2:2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 2: FORM-WOUND EIS
    IEC 60034-18-22:2000 Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions
    BS IEC 61858-2 : 2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 2: FORM-WOUND EIS
    11/30257662 DC : 0 BS EN 60317-0-2 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-2: GENERAL REQUIREMENTS - ENAMELLED RECTANGULAR COPPER WIRE
    IEC 61858-2:2014 Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 2: Form-wound EIS
    10/30206048 DC : 0 BS EN 60317-60 - SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 60: POLYESTER GLASS FIBRE WOUND, IMPREGNATED OR NOT IMPREGNATED, BARE, GRADE 1 OR GRADE 2 ENAMELLED RECTANGULAR COPPER WINDING WIRE WITH TEMPERATURE INDEX 155
    IEC 61858:2008 Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS
    EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60317-0-2:2013 Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective