Skip to content
Please enter a keyword to search

  • IEC 60317-25:2010

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  12-09-2022

    Language(s):  English - French, Spanish, Castilian

    Published date:  10-03-2010

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions and general notes on methods
       of test and appearance
    4 Dimensions
    5 Electrical resistance
    6 Elongation
    7 Springiness
    8 Flexibility and adherence
    9 Heat shock
    10 Cut-through
    11 Resistance to abrasion (nominal conductor diameters
       up to and including 2,500 mm)
    12 Resistance to solvents
    13 Breakdown voltage
    14 Continuity of insulation
    15 Temperature index
    16 Resistance to refrigerants
    17 Solderability
    18 Heat or solvent bonding
    19 Dielectric dissipation factor
    20 Resistance to transformer oil
    21 Loss of mass
    23 Pin hole test
    30 Packaging

    Abstract - (Show below) - (Hide below)

    IEC 60317-25:2010 specifies the requirements of enamelled round aluminium winding wires of class 200 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide-imide resin. The main changes with respect to the previous edition are:
    - Clause 3: addition of 3.3: Appearance;
    - Clause 16: reference to the test for resistance to refrigerants in IEC 60851-4;
    - Clause 22: deletion of the high temperature failure requirement;
    - Clause 23: addition of pin hole test requirement.

    General Product Information - (Show below) - (Hide below)

    Committee TC 55
    Development Note To be read in conjunction with IEC 60317-0-3. (03/2010) Stability Date: 2018. (10/2012)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    I.S. EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    NF EN 61858 : 2009 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    12/30273916 DC : 0 BS EN 61858-1 - ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED EIS - PART-1: WIRE-WOUND WINDING EIS
    BS EN 61858-1:2014 Electrical insulation systems. Thermal evaluation of modifications to an established electrical insulation system (EIS) Wire-wound winding EIS
    BS EN 61858:2008 Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS
    BS 6811-5.0(1993) : AMD 8987 WINDING WIRES - SPECIFICATIONS FOR PARTICULAR TYPES OF ENAMELLED ROUND ALUMINIUM WINDING WIRES - GENERAL REQUIREMENTS
    IEC 60034-18-22:2000 Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions
    I.S. EN 60317-0-3:2008 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-3: GENERAL REQUIREMENTS - ENAMELLED ROUND ALUMINIUM WIRE
    I.S. EN 61858-1:2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS
    IEC 61858-1:2014 Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS
    IEC 61858:2008 Electrical insulation systems - Thermal evaluation of modifications to an established wire-wound EIS
    EN 61858-1:2014 Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS
    EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
    EN 60317-0-3:2008/A1:2013 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-3: GENERAL REQUIREMENTS - ENAMELLED ROUND ALUMINIUM WIRE (IEC 60317-0-3:2008/A1:2013)

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60317-0-3:2008+AMD1:2013 CSV Specifications for particular types of winding wires - Part 0-3:General requirements - Enamelled round aluminium wire
    IEC 60851-5:2008+AMD1:2011 CSV Winding wires - Test methods - Part 5: Electrical properties
    IEC 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective