• IEC 60695-11-20:2015

    Current The latest, up-to-date edition.

    Fire hazard testing - Part 11-20: Test flames - 500 W flame test method

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s): 

    Published date:  22-04-2015

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Significance of the fire tests
    6 Apparatus
    7 Test specimens
    8 Test procedure
    Annex A (normative) - Detailed requirements for the flame
            application point
    Bibliography

    Abstract - (Show below) - (Hide below)

    IEC 60695-11-20:2015 describes a test method consisting of two small-scale laboratory test procedures which is intended to compare the burning behaviour of different materials used in electrotechnical products. Vertically oriented bar specimens or horizontally oriented plate test specimens are exposed to a small flame ignition source with a nominal thermal power of 500 W. The test method uses two test specimen configurations to classify material performance. Rectangular bar-shaped test specimens are used to assess ignitability and burning behaviour, and square plate test specimens are used to assess the resistance of the test specimen to burn-through, as defined in 8.3.3. This test method only applies to materials that have been classified as V-0 or V-1 according to IEC 60695-11-10. This test method is only applicable to solid and cellular materials that have an apparent density of more than 250 kg/m3, determined in accordance with ISO 845. The method does not apply to materials that shrink away from the applied flame without igniting due to their thinness. The test method described provides classifications which may be used for quality assurance, the pre-selection of component materials of products, or to verify the required minimum flammability classification of materials used in end products. If used for pre-selection, then positive results shall be obtained at a test specimen thickness which equals the smallest thickness used in the product application. The results obtained provide some information about the behaviour of materials in service, but cannot by themselves assure safe performance in service. This second edition cancels and replaces the consolidated version of IEC 60695-11-20 published in 2003. This edition constitutes a technical revision. The main changes with respect to the first edition are as follows:
    - The Part title has been modified to the singular - 500 W flame test method;
    - Editorial changes have been made throughout the document for the purpose of aligning IEC 60695-11-10 with IEC 60695-11-20;
    - The Introduction has been modified to clarify the description of the test method;
    - The Scope has been modified for clarification;
    - All occurrences of the term "fixture" have been deleted from the document;
    - Preferred thickness values have been added to 7.2 and 7.3;
    - 7.4.4: 'Thickness measurement' is now numbered 7.5 to which a new Table 1 - Thickness tolerances has been added;
    - New Subclause 8.1.4 'Conditioning of the cotton pad' has been added;
    - 8.2.3 clarifies the application of the test flame to distorted specimens;
    - Explanatory notes have been added to Figures 5 and 6 and the Bibliography has been updated and references added. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with IEC Guide 104 and ISO/IEC Guide 51. Key words: Test flames,Fire Hazard, Fire Test Method

    This publication is to be read in conjunction with IEC 60695-11-3:2012. The contents of the corrigendum of January 2016 have been included in this copy.

    General Product Information - (Show below) - (Hide below)

    Committee TC 89
    Development Note Supersedes ISO 1210 and ISO 10351. (04/2001) Supersedes IEC 61300-2-36. (03/2008) To be read in conjunction with IEC 60695-11-3. Stability date: 2020. (04/2015)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN EN 14482:2011-01 Postal services - Trays for international letter mail - Test methods and performance requirements
    09/30196772 DC : 0 BS ISO 7240-24 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 24: SOUND-SYSTEM LOUDSPEAKERS
    12/30258455 DC : 0 FPREN 60065:2011+FPRAA - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    16/30334902 DC : 0 BS EN ISO 10350-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS
    DIN EN 54-3:2014-09 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    15/30319014 DC : 0 BS EN 62441 ED 1.0 - SAFEGUARDS AGAINST ACCIDENTALLY CAUSED CANDLE FLAME IGNITION
    UNE-EN 60695-1-20:2016 Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance
    08/30176298 DC : DRAFT JAN 2008 BS EN 62477-1 - SAFETY REQUIREMENTS FOR POWER SEMICONDUCTOR CONVERTER SYSTEMS - PART 1: GENERAL
    04/30124761 DC : DRAFT NOV 2004 IEC 61300-2-36 - FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - BASIC TEST AND MEASUREMENT PROCEDURES - PART 2-36: TESTS - FLAMMABILITY (FIRE HAZARD)
    11/30236274 DC : 0 BS ISO 7240-23 - FIRE DETECTION AND ALARM SYSTEMS - PART 23: VISUAL ALARM DEVICES
    BS PD CLC/TS 62441 : 2012 SAFEGUARDS AGAINST ACCIDENTALLY CAUSED CANDLE FLAME IGNITION FOR AUDIO/VIDEO, COMMUNICATION AND INFORMATION TECHNOLOGY EQUIPMENT
    CEI 89-38 : 2014 FIRE HAZARD TESTING - PART 11-11: TEST FLAMES - DETERMINATION OF THE CHARACTERISTIC HEAT FLUX FOR IGNITION FROM A NON-CONTACTING FLAME SOURCE
    BS EN 14482 : 2010 POSTAL SERVICES - TRAYS FOR INTERNATIONAL LETTER MAIL - TEST METHODS AND PERFORMANCE REQUIREMENTS
    BS IEC 62790 : 2014 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES - SAFETY REQUIREMENTS AND TESTS
    09/30184483 DC : 0 BS EN 54-3 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    12/30192217 DC (published 2012-03) BS ISO 12856. Plastic railway sleepers (railroad ties)
    CLC/TS 62441 : 2012 SAFEGUARDS AGAINST ACCIDENTALLY CAUSED CANDLE FLAME IGNITION FOR AUDIO/VIDEO, COMMUNICATION AND INFORMATION TECHNOLOGY EQUIPMENT (IEC/TS 62441:2011)
    DD IEC TS 60695-11-40 : 2002 FIRE HAZARD TESTING - PART 11-40: TEST FLAMES - CONFIRMATORY TESTS - GUIDANCE
    CSA E60691:2008 THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE
    CAN/CSA-C22.2 NO. 60335-2-72:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-72: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES WITH OR WITHOUT TRACTION DRIVE, FOR COMMERCIAL USE
    CSA E60691 : 2008 : R2012 THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE
    CSA C22.2 No. 60691 : 2015 THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE
    BS EN 62368-1 : 2014 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
    CSA C60044-8 : 2007 : R2016 INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRANSFORMERS
    I.S. EN 62109-1:2010 SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS
    ISO 10840:2008 Plastics Guidance for the use of standard fire tests
    BS EN 61730-1 : 2007 PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION
    I.S. EN 54-23:2010 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 23: FIRE ALARM DEVICES - VISUAL ALARM DEVICES
    BS EN 50548 : 2011 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    I.S. EN 50548:2011 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    CSA C22.2 No. 62368-1 : 2014 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
    DIN EN ISO 3673-2 E : 2012 PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012)
    DIN EN 14598-3:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
    DIN EN 14598-2:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements
    EN 60695-9-2 : 2014 FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS (IEC 60695-9-2:2014)
    BS EN IEC 61204-7:2018 Low-voltage switch mode power supplies Safety requirements
    IEC 60691:2015 Thermal-links - Requirements and application guide
    BS EN 62477-1 : 2012 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL (IEC 62477-1:2012)
    IEC 60707:1999 Flammability of solid non-metallic materials when exposed to flame sources - List of test methods
    EN 61800-5-1:2007/A1:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007/A1:2016)
    OVE/ONORM EN 61800-5-1 : 2014 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007)
    CEN/TS 14482 : 2003 POSTAL SERVICES - TRAYS FOR INTERNATIONAL LETTER MAIL - TEST METHODS AND PERFORMANCE REQUIREMENTS
    EN 60707 : 1999 FLAMMABILITY OF SOLID NON-METALLIC MATERIALS WHEN EXPOSED TO FLAME SOURCES - LIST OF TEST METHODS
    EN 60691:2016 THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE (IEC 60691:2015 + COR1:2016)
    EN 61069-7:2016 INDUSTRIAL-PROCESS MEASUREMENT, CONTROL AND AUTOMATION - EVALUATION OF SYSTEM PROPERTIES FOR THE PURPOSE OF SYSTEM ASSESSMENT - PART 7: ASSESSMENT OF SYSTEM SAFETY (IEC 61069-7:2016)
    DIN EN ISO 3672-2:2002-07 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
    EN 60695-1-21 : 2016 FIRE HAZARD TESTING - PART 1-21: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - SUMMARY AND RELEVANCE OF TEST METHODS (IEC 60695-1-21:2016)
    EN 50548 : 2011 AMD 2 2014 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    BS EN 62282-5-1:2012 (published 2013-01) Fuel cell technologies Portable fuel cell power systems. Safety
    I.S. EN 62790:2015 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES - SAFETY REQUIREMENTS AND TESTS
    07/30165210 DC : 0 BS EN ISO 10350-2 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    BS EN 60695-11-10 : 2013 FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS
    S.R. CLC/TS 62441:2012 SAFEGUARDS AGAINST ACCIDENTALLY CAUSED CANDLE FLAME IGNITION FOR AUDIO/VIDEO, COMMUNICATION AND INFORMATION TECHNOLOGY EQUIPMENT (IEC/TS 62441:2011 (EQV))
    NF EN 54-23 : 2010 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 23: FIRE ALARM DEVICES - VISUAL ALARM DEVICES
    07/30169693 DC : 0 BS EN 60695-11-11 - FIRE HAZARD TESTING - PART 11-11: TEST FLAMES - DETERMINATION OF THE IGNITION CHARACTERISTIC HEAT FLUX FROM A NON-CONTACTING FLAME SOURCE
    BS EN 60707:1999 FLAMMABILITY OF SOLID NON-METALLIC MATERIALS WHEN EXPOSED TO FLAME SOURCES - LIST OF TEST METHODS
    I.S. EN 61730-1:2007 PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION
    BS ISO 10840 : 2008 PLASTICS - GUIDANCE FOR THE USE OF STANDARD FIRE TESTS
    UNE-EN 14482:2011 Postal services - Trays for international letter mail - Test methods and performance requirements
    DIN EN 54-24 E : 2008 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 24: COMPONENTS OF VOICE ALARM SYSTEMS - LOUDSPEAKERS
    S.R. TS 62441:2007 ACCIDENTALLY CAUSED CANDLE FLAME IGNITION FOR AUDIO/VIDEO, COMMUNICATION AND INFORMATION TECHNOLOGY EQUIPMENT
    CSA C60044-2 : 2007 : R2011 INSTRUMENT TRANSFORMERS - PART 2: INDUCTIVE VOLTAGE TRANSFORMERS
    CSA C60044-8 : 2007 : R2011 INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRANSFORMERS
    EN IEC 62688 : 2018 CONCENTRATOR PHOTOVOLTAIC (CPV) MODULES AND ASSEMBLIES - SAFETY QUALIFICATION
    IEC TS 62441:2011 Safeguards againts accidentally caused candle flame ignition for audio/video, communication and information technology equipment
    NF EN 60707 : 2000 FLAMMABILITY OF SOLID NON METALLIC MATERIALS WHEN EXPOSED TO FLAME SOURCES - LIST OF TEST METHODS
    ISO/TS 5658-1:2006 Reaction to fire tests Spread of flame Part 1: Guidance on flame spread
    CSA C22.2 No. 0.17 : 2000 EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS
    NF EN 60950-1 : 2006 AMD 2 2014 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials
    IEC TS 60695-1-20:2008 Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance
    I.S. EN 61800-5-1:2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    UNE-EN 54-3:2016 Fire detection and fire alarm systems - Part 3: Fire alarm devices - Sounders
    I.S. EN 60695-9-2:2014 FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS
    DIN EN ISO 10350-2:2011-06 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    CSA C22.2 No. 60335.2.24 : 2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-24: PARTICULAR REQUIREMENTS FOR REFRIGERATING APPLIANCES, ICE-CREAM APPLIANCES AND ICE-MAKERS
    DIN EN 54-23 :2010-06 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 23: FIRE ALARM DEVICES - VISUAL ALARM DEVICES
    DIN EN ISO 14530-2:2000-08 Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999); German version EN ISO 14530-2:1999
    BS EN ISO 14528-2:2000 (published 2000-01) Plastics. Melamine-formaldehyde powder moulding compounds (MF-PMCs) Preparation of test specimens and determination of properties
    BS PD IEC TR 60695-1-21 : 2008 FIRE HAZARD TESTING - PART 1-21: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - SUMMARY AND RELEVANCE OF TEST METHODS
    BS EN ISO 15791-1 : 2013 PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE
    BS EN 14598-2 : 2005 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
    DIN EN 54-3:2001-10 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    I.S. EN ISO 15791-1:2013 PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE (ISO 15791-1:2014)
    I.S. EN ISO 3673-2:2012 PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012)
    IEC 61058-1:2016 RLV Switches for appliances - Part 1: General requirements
    BIS IS 13252-1 : 2010 AMD 1 2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    BIS IS 13252 : 2003 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - GENERAL REQUIREMENTS
    17/30347375 DC : 0 BS EN 62368-1 ED 3.0 - AUDIO/VIDEO; INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
    DIN EN 54-23:2010-06 Fire detection and fire alarm systems - Part 23: Fire alarm devices - Visual alarm devices
    I.S. EN ISO 2897-2:2004 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    12/30258456 DC : 0 BS EN 60950-1:2006/FPRAE:2011 - INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    09/30214460 DC : 0 BS EN 50548 - JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    BS EN 62790 : 2015 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES - SAFETY REQUIREMENTS AND TESTS
    11/30242905 DC : 0 BS EN ISO 3673-2 - PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    14/30287765 DC : 0 BS EN 60695-1-20/ED 1.0 - FIRE HAZARD TESTING - PART 1-20: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - GENERAL GUIDANCE
    BS EN 60695-1-20 : 2016 FIRE HAZARD TESTING - GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - GENERAL GUIDANCE
    CSA C22.2 No. 0.17 : 2000 : R2004 EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS
    CEI CLC/TS 62441 : 2008 ACCIDENTALLY CAUSED CANDLE FLAME IGNITION FOR AUDIO/VIDEO, COMMUNICATION AND INFORMATION TECHNOLOGY EQUIPMENT
    UNI EN 14482 : 2010 This standard specifies the performance requirements and testing methods for standard letter mail trays, as specified in the classification below.
    UNI EN 54-24 : 2008 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 24: COMPONENTS OF VOICE ALARM SYSTEMS - LOUDSPEAKERS
    UNE-EN 61730-1:2007 Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction
    BS ISO 3672-2 : 2000 AMD 13326 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    CSA C60044-2 : 2007 INSTRUMENT TRANSFORMERS - PART 2: INDUCTIVE VOLTAGE TRANSFORMERS
    CSA C60044-8 :2007 INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRANSFORMERS
    EN IEC 61204-7 : 2018 LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS (IEC 61204-7:2016)
    CSA C22.2 No. 0.17 : 2000 : R2013 EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS
    I.S. EN 14482:2010 POSTAL SERVICES - TRAYS FOR INTERNATIONAL LETTER MAIL - TEST METHODS AND PERFORMANCE REQUIREMENTS
    I.S. EN IEC 61204-7:2018 LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS
    CSA C61869-1 : 2014 INSTRUMENT TRANSFORMERS - PART 1: GENERAL REQUIREMENTS
    I.S. EN 60695-11-10:2013 FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS (IEC 60695-11-10:2013 (EQV))
    CEI 89-29 : 2010 FIRE HAZARD TESTING - PART 1-20: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - GENERAL GUIDANCE
    UNE-EN 62790:2015 Junction boxes for photovoltaic modules - Safety requirements and tests
    I.S. EN 60950-1:2006 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005 (MOD))
    ISO/TR 10840:1993 Plastics Burning behaviour Guidance for development and use of fire tests
    ISO 7240-24:2016 Fire detection and fire alarm systems Part 24: Fire alarm loudspeakers
    IEC 61058-1 REDLINE : 4ED 2016 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
    IEC 62368-1:2014 Audio/video, information and communication technology equipment - Part 1: Safety requirements
    IEC 61204-7:2016 EXV LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS
    DIN EN ISO 3672-2 E : 2002 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    DIN EN ISO 2897-2:2004-05 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS EN 60695-1-21:2016 (published 2016-11) Fire hazard testing Guidance for assessing the fire hazard of electrotechnical products. Ignitability. Summary and relevance of test methods
    UNE-EN 60695-9-2:2014 Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods
    IEC TS 60695-9-2:2005 Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods
    BS EN ISO 3673-2:2012 Plastics. Epoxy resins Preparation of test specimens and determination of properties of crosslinked epoxy resins
    IEC 60695-9-2:2014 Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods
    IEC 60695-1-20:2016 Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance
    UNE-EN 62109-1:2011 Safety of power converters for use in photovoltaic power systems -- Part 1: General requirements
    DIN EN ISO 3673-2:2012-10 Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012)
    BS EN 61800-5-1:2007 Adjustable speed electrical power drive systems Safety requirements. Electrical, thermal and energy
    BS EN ISO 10350-2:2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG FIBRE-REINFORCED PLASTICS
    IEC 62282-5-1:2012 Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
    EN ISO 10350-2:2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG FIBRE-REINFORCED PLASTICS
    UNI EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    CSA C22.2 No. 60950-1 :2007 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    CSA C22.2 No. 60950-1 : 2007 : INC : AMD 1 : 2011 : R2012 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    UNI EN 54-3 : 2014 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    EN 62790 : 2015 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES - SAFETY REQUIREMENTS AND TESTS (IEC 62790:2014)
    UL 60335-2-89 : 1 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-89: PARTICULAR REQUIREMENTS FOR COMMERCIAL REFRIGERATING APPLIANCES WITH AN INCORPORATED OR REMOTE REFRIGERANT UNIT OR COMPRESSOR
    UNE-EN 60950-1:2007 Information technology equipment - Safety - Part 1: General requirements
    ONORM EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    CSA C22.2 No. 60950-1 : 2007 : INC : AMD 2 : 2014 : R201200 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    UL 60335-2-67 : 1ED 2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-67: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES, FOR COMMERCIAL USE
    UL 60335-2-72 : 1ED 2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-72: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES WITH OR WITHOUT TRACTION DRIVE, FOR COMMERCIAL USE
    CSA C22.2 No. 60950-1 : 2007 : R2012 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    CSA C22.2 No. 60335-2-40 : 2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-40: PARTICULAR REQUIREMENTS FOR ELECTRICAL HEAT PUMPS, AIR-CONDITIONERS AND DEHUMIDIFIERS
    CSA C22.2 No. 60950-1 : 2007 : INC : UPD 1 : 2011 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    UL 60335-2-40 : 2 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-40: PARTICULAR REQUIREMENTS FOR ELECTRICAL HEAT PUMPS, AIR-CONDITIONERS AND DEHUMIDIFIERS
    CSA C22.2 No. 60950-1 : 2007 : INC : AMD 2 : 2014 : R2016 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    I.S. EN ISO 10350-2:2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    EN ISO 15791-1:2013 PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE (ISO 15791-1:2014)
    UNI EN ISO 3673-2 : 2012 PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS
    UNI EN ISO 15791-1 : 2014 PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE
    UNI EN 54-23 : 2010 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 23: FIRE ALARM DEVICES - VISUAL ALARM DEVICES
    12/30239867 DC : 0 BS EN 62368-1 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
    DD CEN/TS 14482 : 2003 POSTAL SERVICES - TRAYS FOR INTERNATIONAL LETTER MAIL - TEST METHODS AND PERFORMANCE REQUIREMENTS
    12/30272048 DC : DRAFT SEP 2012 BS EN 60691 - THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE
    EN IEC 61058-1 : 2018 SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS (IEC 61058-1:2016)
    05/30139105 DC : DRAFT SEP 2005 IEC 61800-5-1 ED 2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    12/30258453 DC : 0 BS EN 62368-1 AMD - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
    DD ISO/TS 5658-1 : 2006 REACTION TO FIRE TESTS - SPREAD OF FLAME - PART 1: GUIDANCE ON FLAME SPREAD
    CSA C60044-1 : 2007 : R2011 INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS
    CSA C22.2 No. 60335-2-67 : 2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-67: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES, FOR COMMERCIAL USE
    CSA C60044-1 : 2007 INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS
    I.S. EN 62282-5-1:2012 FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012 (EQV))
    I.S. EN 62368-1:2014 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
    I.S. EN 60695-1-20:2016 FIRE HAZARD TESTING - PART 1-20: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - GENERAL GUIDANCE
    BS EN 60691:2016 (published 2016-11) Thermal-links. Requirements and application guide
    I.S. EN 54-3:2014 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    EN 62368-1:2014/AC:2017-03 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
    I.S. EN 54-24:2008 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 24: COMPONENTS OF VOICE ALARM SYSTEMS - LOUDSPEAKERS
    CSA C22.2 No. 250.13 : 2017 LIGHT EMITTING DIODE (LED) EQUIPMENT FOR LIGHTING APPLICATIONS
    IEC TS 60695-11-11:2016 Fire hazard testing - Part 11-11: Test flames - Determination of the characteristic heat flux for ignition from a non-contacting flame source
    IEC TS 60695-11-40:2002 Fire hazard testing - Part 11-40: Test flames - Confirmatory tests - Guidance
    IEC TR 60695-1-21:2008 Fire hazard testing - Part 1-21: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - Summary and relevance of test methods
    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    BS EN ISO 14529-2:2000 (published 2000-01) Plastics. Melamine/phenolic powder moulding compounds (MP-PMCs) Preparation of test specimens and determination of properties
    BS EN 54-23 : 2010 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 23: FIRE ALARM DEVICES - VISUAL ALARM DEVICES
    ISO 2897-2:2003 Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 14528-2:1999 Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 2: Preparation of test specimens and determination of properties
    DD IEC TS 60695-9-2 : DRAFT 2005 FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS
    IEC 62477-1:2012+AMD1:2016 CSV Safety requirements for power electronic converter systems and equipment - Part 1: General
    BS EN ISO 3672-2 : 2001 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    BS IEC TS 60695-9.2 : 2001 FIRE HAZARD TESTING - PART 9-2 - SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS
    BS EN 60695-9-2 : 2014 FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS
    BS EN 62109-1 : 2010 SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS
    IEC 60695-1-21:2016 Fire hazard testing - Part 1-21: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - Summary and relevance of test methods
    ISO 14530-2:1999 Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties
    UNE-EN ISO 15791-1:2014 Plastics - Development and use of intermediate-scale fire tests for plastics products - Part 1: General guidance (ISO 15791-1:2014)
    IEC 61069-7:2016 Industrial-process measurement, control and automation - Evaluation of system properties for the purpose of system assessment - Part 7: Assessment of system safety
    ISO 14529-2:1999 Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties
    UNE-EN 62282-5-1:2013 Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
    UNE-EN ISO 10350-2:2011 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011)
    ISO 3672-2:2000 Plastics Unsaturated-polyester resins (UP-R) Part 2: Preparation of test specimens and determination of properties
    BS EN ISO 14527-2:2000 (published 2000-01) Preparation of test specimens and determination of properties
    ISO 22734-2:2011 Hydrogen generators using water electrolysis process Part 2: Residential applications
    BS EN 14598-3 : 2005 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS
    BS EN 60950-1 : 2006 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    10/30173705 DC : DRAFT SEP 2010 BS EN 62282-5-1 - FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY
    09/30207398 DC : 0 BS ISO 7240-3 - FIRE DETECTION AND ALARM SYSTEMS - PART 3: AUDIBLE ALARM DEVICES
    04/30089617 DC : DRAFT MARCH 2004
    ISO 14526-2:1999 Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties
    ISO 3673-2:2012 Plastics — Epoxy resins — Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins
    09/30150663 DC : 0 BS ISO 22734-2 - HYDROGEN GENERATORS USING WATER ELECTROLYSIS PROCESS - PART 2: RESIDENTIAL APPLICATIONS
    ISO 15791-1:2014 Plastics Development and use of intermediate-scale fire tests for plastics products Part 1: General guidance
    BS EN ISO 2897-2 : 2003 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    UNE-EN 60695-11-10:2014 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    BS ISO 22734-2 : 2011 HYDROGEN GENERATORS USING WATER ELECTROLYSIS PROCESS - PART 2: RESIDENTIAL APPLICATIONS
    BS EN ISO 14526-2:2000 (published 2000-01) Plastics. Phenolic powder moulding compounds (PF-PMCs) Preparation of test specimens and determination of properties
    EN 62109-1 : 2010 SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS
    EN 54-23:2010 Fire detection and fire alarm systems - Part 23: Fire alarm devices - Visual alarm devices
    EN ISO 15252-2 : 1999 PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 14598-2:2005/AC:2006 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
    EN ISO 14529-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN 54-3:2014 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    EN ISO 3672-2 : 2001 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 10350-1:2017 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
    EN 54-24 : 2008 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 24: COMPONENTS OF VOICE ALARM SYSTEMS - LOUDSPEAKERS
    EN ISO 14530-2 : 1999 PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 14528-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 3673-2:2012 PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012)
    EN 14598-3 : 2005 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS
    EN ISO 2897-2 : 2003 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    EN ISO 14527-2 : 1999 PLASTICS - UREA-FORMALDEHYDE AND UREA/MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (UF- AND UF/MF-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    I.S. EN ISO 10350-1:2017 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017)
    DD IEC TS 60695-1-20 : DRAFT MAR 2008 FIRE HAZARD TESTING - PART 1-20: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - GENERAL GUIDANCE
    CSA C22.2 No. 62109-1 : 2016 SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS
    CEI EN 62368-1 : 2016 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS
    I.S. EN 60695-1-21:2016 FIRE HAZARD TESTING - PART 1-21: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - IGNITABILITY - SUMMARY AND RELEVANCE OF TEST METHODS
    12/30211334 DC : 0 BS ISO 15791-1 - PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE (ISO/DIS 15791-1:2012)
    BS EN 54-24 : 2008 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 24: COMPONENTS OF VOICE ALARM SYSTEMS - LOUDSPEAKERS
    I.S. EN 62477-1:2012 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL
    07/30174056 DC : 0 BS EN 60065 - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    BS EN 61069-7:2016 Industrial-process measurement, control and automation. Evaluation of system properties for the purpose of system assessment Assessment of system safety
    PREN 54-3 : DRAFT 2009 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    CSA C22.2 No. 60335-2-89 : 2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-89: PARTICULAR REQUIREMENTS FOR COMMERCIAL REFRIGERATING APPLIANCES WITH AN INCORPORATED OR REMOTE REFRIGERANT UNIT OR COMPRESSOR
    DD CLC/TS 62441 : 2007 ACCIDENTALLY CAUSED CANDLE FLAME IGNITION FOR AUDIO/VIDEO, COMMUNICATION AND INFORMATION TECHNOLOGY EQUIPMENT
    CAN/CSA-C22.2 NO. 60335-2-34:17 Household and similar electrical appliances — Safety — Part 2-34: Particular requirements for motor-compressors (Binational standard with UL 60335-2-34)
    ISO 12856-1:2014 Plastics Plastic railway sleepers for railway applications (railroad ties) Part 1: Material characteristics
    UNE-EN 50548:2012 Junction boxes for photovoltaic modules
    ISO 7240-23:2013 Fire detection and alarm systems Part 23: Visual alarm devices
    I.S. EN 60691:2016 THERMAL-LINKS - REQUIREMENTS AND APPLICATION GUIDE
    I.S. EN 61069-7:2016 INDUSTRIAL-PROCESS MEASUREMENT, CONTROL AND AUTOMATION - EVALUATION OF SYSTEM PROPERTIES FOR THE PURPOSE OF SYSTEM ASSESSMENT - PART 7: ASSESSMENT OF SYSTEM SAFETY
    I.S. EN IEC 62688:2018 CONCENTRATOR PHOTOVOLTAIC (CPV) MODULES AND ASSEMBLIES - SAFETY QUALIFICATION
    DIN EN 54-24:2008-06 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 24: COMPONENTS OF VOICE ALARM SYSTEMS - LOUDSPEAKERS
    NF EN 61800 5-1 : 2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    NF EN 50548 : 2011 AMD 2 2014 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    BS EN ISO 10350-1:2017 Plastics. Acquisition and presentation of comparable single-point data Moulding materials
    PREN 50548 : DRAFT 2009 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
    IEC 61058-1:2016 Switches for appliances - Part 1: General requirements
    ISO 7240-3:2010 Fire detection and alarm systems Part 3: Audible alarm devices
    IEC TR 60695-11-30:2001 Fire hazard testing - Part 11-30: Test flames - History and development from 1979 to 1999
    I.S. EN 60707:1999 FLAMMABILITY OF SOLID NON-METALLIC MATERIALS WHEN EXPOSED TO FLAME SOURCES - LIST OF TEST METHODS
    EN 62477-1:2012/A1:2017 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL (IEC 62477-1:2012/A1:2016)
    DIN EN ISO 15791-1:2014-05 Plastics - Development and use of intermediate-scale fire tests for plastics products - Part 1: General guidance (ISO 15791-1:2014)
    BS ISO 22734-1 : 2008 HYDROGEN GENERATORS USING WATER ELECTROLYSIS PROCESS - PART 1: INDUSTRIAL AND COMMERCIAL APPLICATIONS
    UNE-EN 60695-1-21:2017 Fire hazard testing - Part 1-21: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - Summary and relevance of test methods
    07/30091745 DC : 0 BS IEC 62368 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - SAFETY - REQUIREMENTS
    ISO 15252-2:1999 Plastics Epoxy powder moulding compounds (EP-PMCs) Part 2: Preparation of test specimens and determination of properties
    UNE-EN ISO 3673-2:2013 Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012)
    ISO 22734-1:2008 Hydrogen generators using water electrolysis process Part 1: Industrial and commercial applications
    IEC 62109-1:2010 Safety of power converters for use in photovoltaic power systems - Part 1: General requirements
    16/30354067 DC : 0 BS EN 62282-5-100 - FUEL CELL TECHNOLOGIES - PART 5-100: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY
    BS EN 54-3:2014 FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 3: FIRE ALARM DEVICES - SOUNDERS
    ISO 14527-2:1999 Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and determination of properties
    04/30111706 DC : DRAFT MAR 2004 IEC 60695-9-2 ED.2 - FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS
    BS EN ISO 14530-2:2000 (published 2000-01) Plastics. Unsaturated-polyester powder moulding compounds (UP-PMCs) Preparation of test specimens and determination of properties
    BS EN ISO 15252-2:2000 (published 2000-01) Plastics. Epoxy powder moulding compounds (EP-PMCs) Preparation of test specimens and determination of properties
    15/30322229 DC : 0 BS EN 61800-5-1:2007/AMD 1 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
    NF EN ISO 2897-2 : 2004 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    UNE-ISO 22734-1:2012 Hydrogen generators using water electrolysis process. Part 1: Industrial and commercial applications
    EN 62282-5-1:2012 FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012)
    EN 61730-1:2007/A11:2014 PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2004, MODIFIED)
    EN 14482 : 2010 POSTAL SERVICES - TRAYS FOR INTERNATIONAL LETTER MAIL - TEST METHODS AND PERFORMANCE REQUIREMENTS
    EN 60695-1-20 : 2016 Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 293:2004 Plastics Compression moulding of test specimens of thermoplastic materials
    IEC 60695-1-30:2017 Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines
    IEC 60695-4:2012 Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical products
    ISO 845:2006 Cellular plastics and rubbers Determination of apparent density
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 13943:2017 Fire safety Vocabulary
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    IEC 60695-11-3:2012 Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    AS/NZS 5139:2019 Electrical installations - Safety of battery systems for use with power conversion equipment
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    IEC 60695-1-11:2014 Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment
    IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    IEC 60695-1-10:2016 Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
    ISO 16012:2015 Plastics Determination of linear dimensions of test specimens
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective