IEC 61347-1:2015 RLV

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Terminals
9 Earthing
10 Protection against accidental contact with live parts
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings of ballasts
14 Fault conditions
15 Construction
16 Creepage distances and clearances
17 Screws, current-carrying parts and connections
18 Resistance to heat, fire and tracking
19 Resistance to corrosion
20 No-load output voltage
Annex A (normative) - Test to establish whether a conductive
        part is a live part which may cause an electric shock
Annex B (normative) - Particular requirements for thermally
        protected lamp controlgear
Annex C (normative) - Particular requirements for electronic
        lamp controlgear with means of protection against
        overheating
Annex D (normative) - Requirements for carrying out the heating
        tests of thermally protected lamp controlgear
Annex E (normative) - Use of constant S other than 4500 in
        t[w] tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation of the values
        of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Additional requirements for built-in magnetic
        ballasts with double or reinforced insulation
Annex J (normative) - Schedule of more onerous requirements
Annex K (informative) - Conformity testing during manufacture
Annex L (normative) - Particular additional requirements for
        controlgears providing SELV
Annex M (informative) - Dielectric strength test voltages for
        controlgear intended for the use in impulse withstand
        Category III
Annex N (normative) - Requirements for insulation materials used
        for double or reinforced insulation
Annex O (normative) - Additional requirements for built-in
        electronic controlgear with double or reinforced insulation
Annex P (normative) - Creepage distances and clearances and
        distance through isolation (DTI) for lamp controlgear
        which are protected against pollution by the use of
        coating or potting
Annex Q (informative) - Example for Up calculation
Annex R (informative) - Concept of creepage distances and
        clearances
        coordination
Annex T (informative) - Creepage distances and clearances for
        controlgear with a higher degree of availability
        (impulse withstand category III)
Bibliography

IEC 61347-1:2015 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 61347-1:2015 specifies general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz. This third edition cancels and replaces the second edition published in 2007, Amendment 1:2010 and Amendment 2:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) additional marking requirements;
b) additional requirements for creepage distances and clearances:
- for working voltages with operating frequencies up to 30 kHz;
- for working voltages with higher operating frequencies than 30 kHz;
- for impulse and resonance voltages ignition;
- for basic, supplementary and reinforced insulation;
- for insulation between circuits;
- for coated or potted controlgear;
c) modification of definition of ELV and FELV;
d) modification of schematic drawing, showing the different controlgear classification and insulation requirements;
e) scope extension;
f) new Annex A: test to establish whether a conductive part is a live part which may cause an electric shock;
g) new Annex M: creepage distances and clearances for controlgear where a higher degree of availability (impulse withstand category III) may be requested;
h) new Annex Q: example for Up calculation;
i) new Annex P: creepage distances and clearances and distance through isolation (DTI) for lamp controlgear which are protected against pollution by the use of coating or potting;
j) new Annex R: concept of creepage distances and clearances.