Skip to content
Please enter a keyword to search

  • IEC 62024-2:2008

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    High frequency inductive components - Electrical characteristics and measuring methods - Part 2: Rated current of inductors for DC to DC converters

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  31-12-2021

    Language(s):  English - French, English

    Published date:  08-10-2008

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Standard atmospheric conditions
      4.1 Standard atmospheric conditions for testing
      4.2 Reference conditions
    5 Measuring method of DC saturation limited current
      5.1 General
      5.2 Test conditions
      5.3 Measurement circuit and calculation
      5.4 Attachment jig of inductor
      5.5 Measuring method
      5.6 Quality conformance inspection
    6 Measuring method of temperature rise limited current
      6.1 General
      6.2 Test conditions
      6.3 Measurement jig
          6.3.1 Printed-wiring board method
          6.3.2 Lead wire method
      6.4 Measuring method and calculation
          6.4.1 Resistance-substitution method
          6.4.2 Thermo-couple method
      6.5 Quality conformance inspection
    7 Determination of rated current
    8 Information to be given in the detail specification
      8.1 Measuring method of DC saturation limited current
      8.2 Measuring method of temperature rise limited current
    Annex A (informative) Example of recommended description on
                          product specification sheets and
                          catalogues

    Abstract - (Show below) - (Hide below)

    IEC 62024-2:2008 specifies the measuring methods of the rated direct current limits for small inductors. Standardized measuring methods for the determination of ratings enable users to accurately compare the current ratings given in various manufacturers' data books. This standard is applicable to leaded and surface mount inductors with dimensions according to IEC 62025-1 and generally with rated current less than 22 A, although inductors with rated current greater than 22 A are available that fall within the dimension restrictions of this standard (no larger than 12 mm x 12 mm footprint approximately). These inductors are typically used in DC to DC converters built on PCB, for electric and telecommunication equipment, and small size switching power supply units. The measuring methods are defined by the saturation and temperature rise limitations induced solely by direct current.

    General Product Information - (Show below) - (Hide below)

    Committee TC 51
    Development Note A Bilingual edition has been published. (02/2009) Stability Date: 2020. (09/2017)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    NF EN 62674-1 : 2013 HIGH FREQUENCY INDUCTIVE COMPONENTS - PART 1: FIXED SURFACE MOUNT INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT
    EN 62674-1 : 2012 HIGH FREQUENCY INDUCTIVE COMPONENTS - PART 1: FIXED SURFACE MOUNT INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT (IEC 62674-1:2012)
    BS EN 62674-1:2012 High frequency inductive components Fixed surface mount inductors for use in electronic and telecommunication equipment
    I.S. EN 62674-1:2012 HIGH FREQUENCY INDUCTIVE COMPONENTS - PART 1: FIXED SURFACE MOUNT INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT (IEC 62674-1:2012 (EQV))
    IEC 62674-1:2012 High frequency inductive components - Part 1: Fixed surface mount inductors for use in electronic and telecommunication equipment
    10/30219044 DC : 0 BS EN 62674-1 - HIGH FREQUENCY INDUCTIVE COMPONENTS - FIXED SURFACE MOUNT INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 62025-1:2007 High frequency inductive components - Non-electrical characteristics and measuring methods - Part 1: Fixed, surface mounted inductors for use in electronic and telecommunication equipment
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective