• IEC 62368-1:2014

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Audio/video, information and communication technology equipment - Part 1: Safety requirements

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  31-12-2021

    Language(s): 

    Published date:  26-02-2014

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    0 Principles of this product safety standard
    1 Scope
    2 Normative references
    3 Terms, definitions and abbreviations
    4 General requirements
    5 Electrically-caused injury
    6 Electrically-caused fire
    7 Injury caused by hazardous substances
    8 Mechanically-caused injury
    9 Thermal burn injury
    10 Radiation
    Annex A (informative) - Examples of equipment within
            the scope of this standard
    Annex B (normative) - Normal operating condition tests,
            abnormal operating condition tests and single
            fault condition tests
    Annex C (normative) - UV radiation
    Annex D (normative) - Test generators
    Annex E (normative) - Test conditions for equipment containing
            audio amplifiers
    Annex F (normative) - Equipment markings, instructions, and
            instructional safeguards
    Annex G (normative) - Components
    Annex H (normative) - Criteria for telephone ringing signals
    Annex I (informative) - Overvoltage categories
    Annex J (normative) - Insulated winding wires for use
            without interleaved insulation
    Annex K (normative) - Safety interlocks
    Annex L (normative) - Disconnect devices
    Annex M (normative) - Equipment containing batteries and
            their protection circuits
    Annex N (normative) - Electrochemical potentials (V)
    Annex O (normative) - Measurement of creepage distances
            and clearances
    Annex P (normative) - Safeguards against conductive objects
    Annex Q (normative) - Circuits intended for interconnection
            with building wiring
    Annex R (normative) - Limited short-circuit test
    Annex S (normative) - Tests for resistance to heat and fire
    Annex T (normative) - Mechanical strength tests
    Annex U (normative) - Mechanical strength of CRTs and
            protection against the effects Of implosion
    Annex V (normative) - Determination of accessible parts
    Annex W (informative) - Comparison of terms introduced
            in this standard
    Bibliography

    Abstract - (Show below) - (Hide below)

    IEC 62368-1:2014 deals with the safety of electrical and electronic equipment within the field of audio, video, information and communication technology, and business and office machines with a rated voltage not exceeding 600 V. This standard does not include requirements for performance or functional characteristics of equipment. Examples of equipment within the scope of this standard are given in Annex A. A rated voltage of 600 V is considered to include equipment rated at 400/690 V. This part of IEC 62368 is also applicable to: components and subassemblies intended for incorporation in this equipment. Such components and subassemblies need not comply with every requirement of the standard, provided that the complete equipment, incorporating such components and subassemblies, does comply; external power supply units intended to supply other equipment within the scope of this part of IEC 62368 and accessories intended to be used with equipment within the scope of this part of IEC 62368. This part of IEC 62368 does not apply to power supply systems which are not an integral part of the equipment, such as motor-generator sets, battery backup systems and distribution transformers. This part of IEC 62328 specifies safeguards for ordinary persons, instructed persons, and skilled persons. Additional requirements may apply for equipment that is clearly designed or intended for use by children or specifically attractive to children. This second edition cancels and replaces the first edition published in 2010. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
    - addition of requirements for LEDs;
    - new requirements for wall and ceiling mounting means;
    - addition of acoustic shock requirements for personal music players;
    - revision of the battery requirements, including new requirements for coin/button cell batteries and revision of the burn requirements. Key words: Audio/Video, Safeguards, Information, Communication The contents of the corrigenda of February 2015 and November 2015 have been included in this copy.

    General Product Information - (Show below) - (Hide below)

    Committee TC 108
    Development Note Stability Date: 2015. (02/2014)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    15/30321532 DC : 0 BS EN 62368-3 ED. 1.0 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - SAFETY - PART 3: REMOTE POWER FEEDING
    AAMI IEC TIR 60878 : 2003 GRAPHICAL SYMBOLS FOR ELECTRICAL EQUIPMENT IN MEDICAL PRACTICE
    UNE-EN 62075:2013 Audio/video, information and communication technology equipment - Environmentally conscious design
    UNE-EN 60695-1-10:2017 Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
    BS EN 62087-6 : 2015 AUDIO, VIDEO AND RELATED EQUIPMENT - DETERMINATION OF POWER CONSUMPTION - PART 6: AUDIO EQUIPMENT
    EN 61960-3 : 2017 SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SECONDARY LITHIUM CELLS AND BATTERIES FOR PORTABLE APPLICATIONS - PART 3: PRISMATIC AND CYLINDRICAL LITHIUM SECONDARY CELLS, AND BATTERIES MADE FROM THEM (IEC 61960-3:2017)
    13/30287467 DC : 0 BS EN 62040-1 - UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: GENERAL AND SAFETY REQUIREMENTS FOR UPS
    EN 62680-1-2 : OCT 2017 UNIVERSAL SERIAL BUS INTERFACES FOR DATA AND POWER - PART 1-2: COMMON COMPONENTS - USB POWER DELIVERY SPECIFICATION (IEC 62680-1-2:2017)
    17/30352643 DC : 0 BS IEC 62684 ED2.0 - INTEROPERABILITY SPECIFICATIONS OF COMMON EXTERNAL POWER SUPPLY (EPS) FOR USE WITH DATA-ENABLED MOBILE TELEPHONES
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    PD IEC/TR 60878:2015 Graphical symbols for electrical equipment in medical practice
    PREN 50332-2 : DRAFT 2013 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PORTABLE AUDIO EQUIPMENT - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY AND LIMIT CONSIDERATIONS - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY
    15/30327916 DC : 0 BS EN 63002 ED. 1.0 - DENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNALPOWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES (TA 14)
    I.S. EN 62087-6:2015 AUDIO, VIDEO AND RELATED EQUIPMENT - DETERMINATION OF POWER CONSUMPTION - PART 6: AUDIO EQUIPMENT
    ECMA 341 : 4ED 2010 ENVIRONMENTAL DESIGN CONSIDERATIONS FOR ICT & CE PRODUCTS
    BS EN 61960-3:2017 SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SECONDARY LITHIUM CELLS AND BATTERIES FOR PORTABLE APPLICATIONS - PART 3: PRISMATIC AND CYLINDRICAL LITHIUM SECONDARY CELLS, AND BATTERIES MADE FROM THEM (IEC 61960-3:2017)
    CLC/TR 50656 : 2016 SPD APPLICATION IN CONJUNCTION WITH CLASS 2 EQUIPMENT
    14/30312710 DC : 0 BS EN 62911 ED. 1.0 - AUDIO, VIDEO AND INFORMATION TECHNOLOGY EQUIPMENT - ROUTINE ELECTRICAL SAFETY TESTING IN PRODUCTION
    BS PD CLC/TR 50656 : 2016 SPD APPLICATION IN CONJUNCTION WITH CLASS 2 EQUIPMENT
    EN 63002 : 2017 IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES (IEC 63002:2016)
    14/30280175 DC : 0 BS EN 61204-7 - LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS
    CEI EN 62949 : 1ED 2017 PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO INFORMATION AND COMMUNICATION NETWORKS
    PD ISO/IEC GUIDE 50:2014 Safety aspects. Guidelines for child safety in standards and other specifications
    11/30246444 DC : 0 BS EN 62075 ED 2.0 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN
    13/30280858 DC : 0 BS EN 60940 - GUIDANCE INFORMATION ON THE APPLICATION OF CAPACITORS, RESISTORS, INDUCTORS AND COMPLETE FILTER UNITS FOR RADIO INTERFERENCE SUPPRESSION - PART 8: SECTIONAL SPECIFICATION: FIXED CAPACITORS OF CERAMIC DIELECTRIC, CLASS 1
    13/30281665 DC : 0 BS EN 50332-2 - SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PORTABLE AUDIO EQUIPMENT - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY AND LIMIT CONSIDERATIONS - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY
    10/30240267 DC : 0 BS EN 60601-2-66 ED.1 - ELECTROACOUSTICS - PART 2-66: HEARING INSTRUMENTS AND HEARING SYSTEMS - GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE
    IEEE C62.33 : 1982 TEST METHODS AND PERFORMANCE VALUES FOR METAL-OXIDE VARISTOR SURGE PROTECTIVE COMPONENTS
    BS EN 63002 : 2017 IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES
    I.S. EN 62949:2017 PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO INFORMATION AND COMMUNICATION NETWORKS
    13/30240399 DC : 0 ISO/IEC GUIDE 51 - SAFETY ASPECTS - GUIDELINES FOR THEIR INCLUSION IN STANDARDS
    EN 50332-3 : 2017 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 3: MEASUREMENT METHOD FOR SOUND DOSE MANAGEMENT
    13/30293673 DC : 0 BS EN 61960 - SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SECONDARY LITHIUM CELLS AND BATTERIES FOR PORTABLE APPLICATIONS
    16/30351255 DC : 0 BS EN 61960-4 ED 1.0 - SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - PART 4: COIN TYPE SECONDARY LITHIUM CELLS AND BATTERIES
    16/30354071 DC : 0 BS EN 62282-3-100 - FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    IEC 60950-22 REDLINE : 2ED 2016 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 22: EQUIPMENT TO BE INSTALLED OUTDOORS
    NF EN 62949 : 2017 PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO INFORMATION AND COMMUNICATION NETWORKS
    PD ISO/IEC GUIDE 51:2014 (published 2014-04) Safety aspects. Guidelines for their inclusion in standards
    UNE-EN 60065:2015 Audio, video and similar electronic apparatus - Safety requirements
    BS EN 62949 : 2017 PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO INFORMATION AND COMMUNICATION NETWORKS (IEC 62949:2017)
    15/30321536 DC : 0 BS EN 62949 ED. 1.0 - PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO PAIREDCONDUCTOR COMMUNICATION NETWORKS
    15/30287154 DC : 0 BS EN 60601-2-40 ED 2.0 - MEDICAL ELECTRICAL EQUIPMENT - PART 2-40: PARTICULAR REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE OF ELECTROMYOGRAPHS AND EVOKED RESPONSE EQUIPMENT - PROPOSED HORIZONTAL STANDARD
    16/30338723 DC : 0 BS EN 61643-11:2012/A - LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 11: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER SYSTEMS - REQUIREMENTS AND TEST METHODS
    BS EN 62911:2016 Audio, video and information technology equipment. Routine electrical safety testing in production
    15/30329267 DC : 0 BS EN 60747-17 - SEMICONDUCTOR DEVICES - PART 17: MAGNETIC AND CAPACITIVE COUPLER FOR BASIC AND REINFORCED ISOLATION
    BS EN 50332-3:2017 (published 2017-02) Sound system equipment: headphones and earphones associated with personal music players. Maximum sound pressure level measurement methodology Measurement method for sound dose management
    BS EN IEC 63044-3:2018 Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) Electrical safety requirements
    BS EN 60940 : 2015 GUIDANCE INFORMATION ON THE APPLICATION OF CAPACITORS, RESISTORS, INDUCTORS AND COMPLETE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION
    EN 62949 : 2017 PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO INFORMATION AND COMMUNICATION NETWORKS (IEC 62949:2017)
    BS EN 50332-2:2013 (published 2013-10) Sound system equipment: Headphones and earphones associated with personal music players. Maximum sound pressure level measurement methodology Matching of sets with headphones if either or both are offered separately, or are offered as one package equipment but with standardised connectors between the two allowing to combine components of different manufacturers or different design
    BS EN 50604-1:2016 (published 2016-08) Secondary lithium batteries for light EV (electric vehicle) applications General safety requirements and test methods
    IEC 61938 : 3.0 MULTIMEDIA SYSTEMS - GUIDE TO THE RECOMMENDED CHARACTERISTICS OF ANALOGUE INTERFACES TO ACHIEVE INTEROPERABILITY
    EN IEC 61204-7 : 2018 LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS (IEC 61204-7:2016)
    BS EN 61938 : 2013 MULTIMEDIA SYSTEMS - GUIDE TO THE RECOMMENDED CHARACTERISTICS OF ANALOGUE INTERFACES TO ACHIEVE INTEROPERABILITY
    BS EN 60950-22:2017 (published 2017-08) Information technology equipment. Safety Equipment to be installed outdoors
    CSA C22.2 No. 60065 : 2016 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    IEC 60990 REDLINE : 3ED 2016 METHODS OF MEASUREMENT OF TOUCH CURRENT AND PROTECTIVE CONDUCTOR CURRENT
    CEI EN 62075 : 2013 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN
    IEC GUIDE 110:2014 Home control systems - Guidelines relating to safety
    PD IEC/TS 60695-1-14:2017 (published 2018-01) Fire hazard testing Guidance on the different levels of power and energy related to the probability of ignition and fire in low voltage electrotechnical products
    IEC 61938:2018 RLV Multimedia systems - Guide to the recommended characteristics of analogue interfaces to achieve interoperability (GMT)
    IEC 60335-2-82:2017 Household and similar electrical appliances - Safety - Part 2-82: Particular requirements for amusement machines and personal service machines
    EN 50131-1:2006/A2:2017 ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS
    CEI EN 50332-3 : 1ED 2017 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 3: MEASUREMENT METHOD FOR SOUND DOSE MANAGEMENT
    IEC 61204-7:2016 EXV LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS
    BS PD IEC TR 63079 : 2017 CODE OF PRACTICE FOR HEARING-LOOP SYSTEMS (HLS)
    CEI EN 61938 : 2014 MULTIMEDIA SYSTEMS - GUIDE TO THE RECOMMENDED CHARACTERISTICS OF ANALOGUE INTERFACES TO ACHIEVE INTEROPERABILITY
    IEC 62949:2017 Particular safety requirements for equipment to be connected to information and communication technology networks
    EN 50604-1:2016 SECONDARY LITHIUM BATTERIES FOR LIGHT EV (ELECTRIC VEHICLE) APPLICATIONS - PART 1: GENERAL SAFETY REQUIREMENTS AND TEST METHODS
    BS EN 50131-1 : 2006 ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS
    I.S. EN 61960-3:2017 SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SECONDARY LITHIUM CELLS AND BATTERIES FOR PORTABLE APPLICATIONS - PART 3: PRISMATIC AND CYLINDRICAL LITHIUM SECONDARY CELLS, AND BATTERIES MADE FROM THEM
    I.S. EN IEC 60728-3:2018 CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 3: ACTIVE WIDEBAND EQUIPMENT FOR CABLE NETWORKS (TA 5)
    I.S. EN IEC 62684:2018 INTEROPERABILITY SPECIFICATIONS OF COMMON EXTERNAL POWER SUPPLY (EPS) FOR USE WITH DATA-ENABLED MOBILE TELEPHONES
    I.S. EN 50332-2:2013 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY, OR ARE OFFERED AS ONE PACKAGE EQUIPMENT BUT WITH STANDARDISED CONNECTORS BETWEEN THE TWO ALLOWING TO COMBINE COMPONENTS OF DIFFERENT MANUFACTURERS
    I.S. EN 62911:2016 AUDIO, VIDEO AND INFORMATION TECHNOLOGY EQUIPMENT - ROUTINE ELECTRICAL SAFETY TESTING IN PRODUCTION
    I.S. EN IEC 61938:2018 MULTIMEDIA SYSTEMS - GUIDE TO THE RECOMMENDED CHARACTERISTICS OF ANALOGUE INTERFACES TO ACHIEVE INTEROPERABILITY
    I.S. EN 60065:2014 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS
    I.S. EN 60950-22:2017 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 22: EQUIPMENT TO BE INSTALLED OUTDOORS
    EN 50174-3:2013/A1:2017 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    I.S. EN 61643-11:2012 LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 11: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER SYSTEMS - REQUIREMENTS AND TESTS METHODS
    ES 203 474 : 1.1.1 ENVIRONMENTAL ENGINEERING (EE); INTERFACING OF RENEWABLE ENERGY OR DISTRIBUTED POWER SOURCES TO 400 VDC DISTRIBUTION SYSTEMS POWERING INFORMATION AND COMMUNICATION TECHNOLOGY (ICT) EQUIPMENT
    BS EN 62075 : 2012 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN
    I.S. EN 62733:2015 PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR - GENERAL AND SAFETY REQUIREMENTS
    IEC 61204-3 REDLINE : 3ED 2016 LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 3: ELECTROMAGNETIC COMPATIBILITY (EMC)
    I.S. EN 60990:2016 METHODS OF MEASUREMENT OF TOUCH CURRENT AND PROTECTIVE CONDUCTOR CURRENT
    I.S. EN IEC 63044-3:2018 HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 3: ELECTRICAL SAFETY REQUIREMENTS
    I.S. EN 60695-1-10:2017 FIRE HAZARD TESTING - PART 1-10: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - GENERAL GUIDELINES
    I.S. EN 50174-3:2013 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS
    ECMA/TR 106 : 1ED 2013 GUIDANCE AND COMPARISON BETWEEN 60950-1 AND 62368-1
    IEC 60695-1-10 REDLINE : 2ED 2016 FIRE HAZARD TESTING - PART 1-10: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - GENERAL GUIDELINES
    BS EN 60990:2000 Methods of measurement of touch current and protective conductor current
    CSA C22.2 No. 60601.2.40 : 2017 MEDICAL ELECTRICAL EQUIPMENT - PART 2-40: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF ELECTROMYOGRAPHS AND EVOKED RESPONSE EQUIPMENT
    I.S. EN IEC 61204-7:2018 LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS
    BS EN 60065 : 2014 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014, MODIFIED)
    I.S. EN 50332-3:2017 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 3: MEASUREMENT METHOD FOR SOUND DOSE MANAGEMENT
    I.S. EN 62680-1-2:2017 UNIVERSAL SERIAL BUS INTERFACES FOR DATA AND POWER - PART 1-2: COMMON COMPONENTS - USB POWER DELIVERY SPECIFICATION
    EN IEC 60728-3 : 2018 CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 3: ACTIVE WIDEBAND EQUIPMENT FOR CABLE NETWORKS (TA 5) (IEC 60728-3:2017)
    IEC GUIDE 112:2017 Guide on the safety of multimedia equipment
    EN IEC 61938 : 2018 MULTIMEDIA SYSTEMS - GUIDE TO THE RECOMMENDED CHARACTERISTICS OF ANALOGUE INTERFACES TO ACHIEVE INTEROPERABILITY (IEC 61938:2018)
    I.S. EN 60950-1:2006 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005 (MOD))
    BS PD IEC TR 60601-4-3 : 2015 MEDICAL ELECTRICAL EQUIPMENT - PART 4-3: GUIDANCE AND INTERPRETATION - CONSIDERATIONS OF UNADDRESSED SAFETY ASPECTS IN THE THIRD EDITION OF IEC 60601-1 AND PROPOSALS FOR NEW REQUIREMENTS
    CEI EN 63002 : 1ED 2017 IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES
    EN IEC 63044-3 : 2018 HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 3: ELECTRICAL SAFETY REQUIREMENTS (IEC 63044-3:2017)
    NF EN 60950-22 : 2017 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 22: EQUIPMENT TO BE INSTALLED OUTDOORS
    EN IEC 62684 : 2018 INTEROPERABILITY SPECIFICATIONS OF COMMON EXTERNAL POWER SUPPLY (EPS) FOR USE WITH DATA-ENABLED MOBILE TELEPHONES (IEC 62684:2018)
    IEC TR 60878:2015 Graphical symbols for electrical equipment in medical practice
    S.R. CLC/TR 50656:2016 SPD APPLICATION IN CONJUNCTION WITH CLASS 2 EQUIPMENT
    IEC 62684:2018 INTEROPERABILITY SPECIFICATIONS OF COMMON EXTERNAL POWER SUPPLY (EPS) FOR USE WITH DATA-ENABLED MOBILE TELEPHONES
    I.S. EN 60940:2015 GUIDANCE INFORMATION ON THE APPLICATION OF CAPACITORS, RESISTORS, INDUCTORS AND COMPLETE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION
    I.S. EN 63002:2017 IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES
    IEC 62040-1:2017 EXV UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS
    ISO/IEC Guide 50:2014 Safety aspects Guidelines for child safety in standards and other specifications
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    I.S. EN 61938:2013 MULTIMEDIA SYSTEMS - GUIDE TO THE RECOMMENDED CHARACTERISTICS OF ANALOGUE INTERFACES TO ACHIEVE INTEROPERABILITY (IEC 61938:2013 (EQV))
    I.S. EN 62075:2012 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN (IEC 62075:2012 (EQV))
    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    IEC 61204-3:2016 Low-voltage switch mode power supplies - Part 3: Electromagnetic compatibility (EMC)
    IEC 62368-3:2017 Audio/video, information and communication technology equipment - Part 3: Safety aspects for DC power transfer through communication cables and ports
    IEC 60728-3:2017 RLV Cable networks for television signals, sound signals and interactive services - Part 3: Active wideband equipment for cable networks
    IEC TR 63167:2018 ASSESSMENT OF CONTACT CURRENT RELATED TO HUMAN EXPOSURE TO ELECTRIC, MAGNETIC AND ELECTROMAGNETIC FIELDS
    IEC TS 60695-1-14:2017 Fire hazard testing - Part 1-14: Guidance on the different levels of power and energy related to the probability of ignition and fire in low voltage electrotechnical products
    IEC 60601-2-40:2016 Medical electrical equipment - Part 2-40: Particular requirements for the basic safety and essential performance of electromyographs and evoked response equipment
    I.S. EN 50131-1:2006 ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS
    EN 60950-22 : 2017 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 22: EQUIPMENT TO BE INSTALLED OUTDOORS (IEC 60950-22:2016)
    IEC 60728-3 : 5.0 CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 3: ACTIVE WIDEBAND EQUIPMENT FOR CABLE NETWORKS
    15/30319022 DC : 0 BS EN 60990 ED 3.0 - METHODS OF MEASUREMENT OF TOUCH CURRENT AND PROTECTIVE CONDUCTOR CURRENT
    BS EN 62733:2015 (published 2018-04) Programmable components in electronic lamp controlgear. General and safety requirements
    13/30248264 DC : 0 BS EN 62733 - PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS
    BS EN IEC 61204-7:2018 Low-voltage switch mode power supplies Safety requirements
    BS PD IEC TS 62850 : 2013 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - GENERAL REQUIREMENTS FOR EQUIPMENT INTENDED TO BE USED IN EDUCATIONAL ESTABLISHMENTS BY CHILDREN
    IEC 62911:2016 Audio, video and information technology equipment - Routine electrical safety testing in production
    BS EN 60825-1:2014 (published 2017-12) Safety of laser products Equipment classification and requirements
    IEC 60990:2016 Methods of measurement of touch current and protective conductor current
    BS EN 60730-1:2011 Automatic electrical controls for household and similar use General requirements
    IEC TS 62850:2013 Safety requirements for electrical equipment for measurement, control, and laboratory use - General requirements for equipment intended to be used in educational establishments by children
    17/30361391 DC : 0 BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
    14/30315309 DC : 0 BS EN 61204-3 - LOW VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: ELECTROMAGNETIC COMPATIBILITY (EMC)
    IEC TS 62933-5-1:2017 Electrical energy storage (EES) systems - Part 5-1: Safety considerations for grid-integrated EES systems - General specification
    IEC 60950-22:2016 Information technology equipment - Safety - Part 22: Equipment to be installed outdoors
    IEC 62075:2012 Audio/video, information and communication technology equipment - Environmentally conscious design
    IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
    BS EN 60950-1 : 2006 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    IEC 60940:2015 Guidance information on the application of capacitors, resistors, inductors and complete filter units for electromagnetic interference suppression
    14/30303914 DC : 0 BS EN 50604-1 - SECONDARY LITHIUM BATTERIES FOR LEV (LIGHT ELECTRIC VEHICLE) APPLICATIONS - PART 1: GENERAL SAFETY REQUIREMENTS AND TEST METHODS
    16/30351274 DC : 0 BS EN 62933-5-1 - ELECTRICAL ENERGY STORAGE (ESS) SYSTEMS - PART 5-1: SAFETY CONSIDERATIONS RELATED TO GRID INTEGRATED ELECTRICAL ENERGY STORAGE (EES) SYSTEMS
    UNE-EN 60825-1:2015 Safety of laser products - Part 1: Equipment classification and requirements
    I.S. EN 60825-1:2014 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS
    CSA C22.2 No. 60950-1 :2007 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    CSA C22.2 No. 60950-1 : 2007 : INC : AMD 1 : 2011 : R2012 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    UNE-EN 60950-1:2007 Information technology equipment - Safety - Part 1: General requirements
    CSA C22.2 No. 60950-1 : 2007 : INC : AMD 2 : 2014 : R201200 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    CSA C22.2 No. 60950-1 : 2007 : R2012 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    CSA C22.2 No. 60950-1 : 2007 : INC : UPD 1 : 2011 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    CSA C22.2 No. 60950-1 : 2007 : INC : AMD 2 : 2014 : R2016 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
    UL 60730-1 : 5ED 2016-08 AUTOMATIC ELECTRICAL CONTROLS - PART 1: GENERAL REQUIREMENTS
    EN 60065:2014/AC:2017-01 AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016)
    IEC 60728-3:2017 Cable networks for television signals, sound signals and interactive services - Part 3: Active wideband equipment for cable networks
    EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
    DIN 820-12:2014-06 STANDARDIZATION - PART 12: GUIDELINES FOR THE INCLUSION OF SAFETY ASPECTS IN STANDARDS (ISO/IEC GUIDE 51:2014)
    EN 62733:2015/AC:2017-09 PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR - GENERAL AND SAFETY REQUIREMENTS
    IEC 60695-1-10:2016 RLV FIRE HAZARD TESTING - PART 1-10: GUIDANCE FOR ASSESSING THE FIRE HAZARD OF ELECTROTECHNICAL PRODUCTS - GENERAL GUIDELINES
    IEC 61204-3:2016 RLV Low-voltage switch mode power supplies - Part 3: Electromagnetic compatibility (EMC)
    IEC 61938:2018 Multimedia systems - Guide to the recommended characteristics of analogue interfaces to achieve interoperability (GMT)
    EN 60730-1:2016 AUTOMATIC ELECTRICAL CONTROLS - PART 1: GENERAL REQUIREMENTS (IEC 60730-1:2013, MODIFIED + COR1:2014)
    EN 60990:2016 METHODS OF MEASUREMENT OF TOUCH CURRENT AND PROTECTIVE CONDUCTOR CURRENT (IEC 60990:2016)
    EN 62087-6 : 2015 AUDIO, VIDEO AND RELATED EQUIPMENT - DETERMINATION OF POWER CONSUMPTION - PART 6: AUDIO EQUIPMENT (IEC 62087-6:2015)
    EN 50332-2:2013 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY, OR ARE OFFERED AS ONE PACKAGE EQUIPMENT BUT WITH STANDARDISED CONNECTORS BETWEEN THE TWO ALLOWING TO COMBINE COMPONENTS OF DIFFERENT MANUFACTURERS
    EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
    EN 60940 : 2015 GUIDANCE INFORMATION ON THE APPLICATION OF CAPACITORS, RESISTORS, INDUCTORS AND COMPLETE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION (IEC 60940:2015)
    EN 62075:2012/AC:2013 AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - ENVIRONMENTALLY CONSCIOUS DESIGN (IEC 62075:2012)
    IEC 60990:2016 RLV Methods of measurement of touch current and protective conductor current
    EN 61643-11:2012/A11:2018 LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 11: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER SYSTEMS - REQUIREMENTS AND TEST METHODS
    IEC 60950-22:2016 RLV Information technology equipment - Safety - Part 22: Equipment to be installed outdoors
    EN 62911 : 2016 AUDIO, VIDEO AND INFORMATION TECHNOLOGY EQUIPMENT - ROUTINE ELECTRICAL SAFETY TESTING IN PRODUCTION (IEC 62911:2016)

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    IEC 60112:2003+AMD1:2009 CSV METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
    IEC 60320-1:2015 Appliance couplers for household and similar general purposes - Part 1: General requirements
    ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
    IEC 60906-3:1994 IEC System of plugs and socket-outlets for household and similar purposes - Part 3: SELV plugs and socket-outlets, 16 A 6V, 12 V, 24 V, 48 V, a.c. and d.c.
    IEC 60728-11:2016 Cable networks for television signals, sound signals and interactive services - Part 11: Safety
    IEC 61643-321:2001 Components for low-voltage surge protective devices - Part 321: Specifications for avalanche breakdown diode (ABD)
    IEC 61558-2-1:2007 SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 2-1: PARTICULAR REQUIREMENTS AND TESTS FOR SEPARATING TRANSFORMERS AND POWER SUPPLIES INCORPORATING SEPARATING TRANSFORMERS FOR GENERAL APPLICATIONS
    IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS)
    IEC 60245-1:2003+AMD1:2007 CSV Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 1: General requirements
    ISO 7010:2011 Graphical symbols Safety colours and safety signs Registered safety signs
    IEC 60998-1:2002 Connecting devices for low-voltage circuits for household and similar purposes - Part 1: General requirements
    IEC 60738-1:2006+AMD1:2009 CSV Thermistors - Directly heated positive temperature coefficient -Part 1: Generic specification
    IEC TS 60479-1:2005+AMD1:2016 CSV Effects of current on human beings and livestock - Part 1: Generalaspects
    IEC 60107-1:1997 Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequencies
    IEC 60664-4:2005 Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress
    IEC 61984:2008 Connectors - Safety requirements and tests
    IEC 60384-14:2013+AMD1:2016 CSV Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
    ISO 871:2006 Plastics Determination of ignition temperature using a hot-air furnace
    IEC 60896-11:2002 Stationary lead-acid batteries - Part 11: Vented types - General requirements and methods of tests
    IEC 61427 : 2.0 SECONDARY CELLS AND BATTERIES FOR PHOTOVOLTAIC ENERGY SYSTEMS (PVES) - GENERAL REQUIREMENTS AND METHODS OF TEST
    ISO 3864-2:2016 Graphical symbols Safety colours and safety signs Part 2: Design principles for product safety labels
    EN 50491-3 : 2009 GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 3: ELECTRICAL SAFETY REQUIREMENTS
    IEC 61558-2-4:2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-4: PARTICULAR REQUIREMENTS AND TESTS FOR ISOLATING TRANSFORMERS AND POWER SUPPLY UNITS INCORPORATING ISOLATING TRANSFORMERS
    IEC 61293:1994 MARKING OF ELECTRICAL EQUIPMENT WITH RATINGS RELATED TO ELECTRICAL SUPPLY - SAFETY REQUIREMENTS
    IEC TS 61201:2007 Use of conventional touch voltage limits - Application guide
    IEC TR 60083:2015 Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC
    ISO 9773:1998 Plastics Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source
    IEC 60332-1-3:2004+AMD1:2015 CSV Tests on electric and optical fibre cables under fire conditions - Part 1-3: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for determination of flamingdroplets/particles
    IEC TR 62471-2:2009 Photobiological safety of lamps and lamp systems - Part 2: Guidance on manufacturing requirements relating to non-laser optical radiation safety
    IEC 60169-3:1965 Radio-frequency connectors - Part 3: Two-pin connector for twin balanced aerial feeders
    IEC 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
    IEC 60896-21:2004 Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test
    IEC 60269-2:2013+AMD1:2016 CSV Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K
    IEC 62151:2000 Safety of equipment electrically connected to a telecommunication network
    IEC 61558-2-16:2009+AMD1:2013 CSV Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units
    IEC 60130-9:2011 Connectors for frequencies below 3 MHz - Part 9: Circular connectors for radio and associated sound equipment
    IEC 60332-2-2:2004 TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 2-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE SMALL INSULATED WIRE OR CABLE -PROCEDURE FOR DIFFUSION FLAME
    IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
    CFR 21(PTS800-1299) : 0 FOOD AND DRUGS - FOOD AND DRUG ADMINISTRATION, CHAPTER 1 DEPARTMENT OF HEALTH AND HUMAN SERVICES - PARTS 800-1299
    ISO 8256:2004 Plastics Determination of tensile-impact strength
    IEC 60825-12:2004 Safety of laser products - Part 12: Safety of free space optical communication systems used for transmission of information
    IEC 60227-2:1997+AMD1:2003 CSV Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 2: Test methods
    IEC 61810-1:2015 Electromechanical elementary relays - Part 1: General and safety requirements
    IEC 60950-22:2016 Information technology equipment - Safety - Part 22: Equipment to be installed outdoors
    IEC 60950-23:2005 Information technology equipment - Safety - Part 23: Large data storage equipment
    IEC 61643-21:2000+AMD1:2008+AMD2:2012 CSV Low voltage surge protective devices - Part 21: Surge protective devices connected to telecommunications and signalling networks - Performance requirements and testing methods
    IEC 60695-10-3:2016 FIRE HAZARD TESTING - PART 10-3: ABNORMAL HEAT - MOULD STRESS RELIEF DISTORTION TEST
    IEC 60027-1:1992 Letters symbols to be used in electrical technology - Part 1: General
    IEC 60851-6:2012 WINDING WIRES - TEST METHODS - PART 6: THERMAL PROPERTIES
    IEC 60851-5:2008+AMD1:2011 CSV Winding wires - Test methods - Part 5: Electrical properties
    IEC 61643-311:2013 Components for low-voltage surge protective devices - Part 311: Performance requirements and test circuits for gas discharge tubes (GDT)
    IEC 61056-2:2012 General purpose lead-acid batteries (valve-regulated types) - Part 2: Dimensions, terminals and marking
    IEC 60227-1:2007 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 1: General requirements
    IEC 60332-1-2:2004+AMD1:2015 CSV Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame
    IEC 60999-1:1999 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
    EN 60728-11 : 2017 CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 11: SAFETY (IEC 60728-11:2016 + COR1:2016)
    IEC 60601-2-4:2010 Medical electrical equipment - Part 2-4: Particular requirements for the basic safety and essential performance of cardiac defibrillators
    IEC 60085:2007 ELECTRICAL INSULATION - THERMAL EVALUATION AND DESIGNATION
    IEC TR 62368-2:2015 Audio/video, information and communication technology equipment - Part 2: Explanatory information related to IEC 62368-1
    IEC 60320-2-2:1998 Appliance couplers for household and similar general purposes - Part 2-2: Interconnection couplers for household and similar equipment
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    IEC 61558-1:2017 Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests
    EN 50332-1:2013 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 1: GENERAL METHOD FOR "ONE PACKAGE EQUIPMENT"
    ISO/IEC Guide 37:2012 Instructions for use of products by consumers
    EN 71-1:2014 SAFETY OF TOYS - PART 1: MECHANICAL AND PHYSICAL PROPERTIES
    IEC 61643-1:2005 Low-voltage surge protective devices - Part 1: Surge protective devices connected to low-voltage power distribution systems - Requirements and tests
    ISO 180:2000 Plastics Determination of Izod impact strength
    IEC 60906-2:2011 IEC system of plugs and socket-outlets for household and similar purposes - Part 2: Plugs and socket-outlets 15 A 125 V a.c. and 20 A 125 V a.c.
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    ISO 9772:2012 Cellular plastics Determination of horizontal burning characteristics of small specimens subjected to a small flame
    IEC 61058-1:2016 Switches for appliances - Part 1: General requirements
    IEC 60896-22:2004 Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements
    IEC 60364-4-44:2007+AMD1:2015 CSV Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
    IEC 60691:2015 Thermal-links - Requirements and application guide
    IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
    IEC 61056-1:2012 General purpose lead-acid batteries (valve-regulated types) - Part 1: General requirements, functional characteristics - Methods of test
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    IEC 61051-2:1991 Varistors for use in electronic equipment - Part 2: Sectional specification for surge suppression varistors
    IEC 61643-11:2011 Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods
    IEC TS 60695-11-21:2005 FIRE HAZARD TESTING - PART 11-21: TEST FLAMES - 500 W VERTICAL FLAME TEST METHOD FOR TUBULAR POLYMERIC MATERIALS
    IEC 60906-1:2009 IEC system of plugs and socket-outlets for household and similar purposes - Part 1: Plugs and socket-outlets 16 A 250 V a.c.
    EN 50332-2:2013 SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY, OR ARE OFFERED AS ONE PACKAGE EQUIPMENT BUT WITH STANDARDISED CONNECTORS BETWEEN THE TWO ALLOWING TO COMBINE COMPONENTS OF DIFFERENT MANUFACTURERS
    IEC 60851-3:2009+AMD1:2013 CSV Winding wires - Test methods - Part 3: Mechanical properties
    IEC 60664-5:2007 Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
    ISO 4892-4:2013 Plastics Methods of exposure to laboratory light sources Part 4: Open-flame carbon-arc lamps
    IEC 62471:2006 Photobiological safety of lamps and lamp systems
    ISO 179-1:2010 Plastics Determination of Charpy impact properties Part 1: Non-instrumented impact test
    ISO 4892-2:2013 Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps
    IEC 61965:2003 Mechanical safety of cathode ray tubes
    IEC 61434:1996 Secondary cells and batteries containing alkaline or other non-acid electrolytes - Guide to designation of current in alkaline secondary cell and battery standards
    IEC 60664-3:2016 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 3: USE OF COATING, POTTING OR MOULDING FOR PROTECTION AGAINST POLLUTION
    IEC 61643-331:2003 Components for low-voltage surge protective devices - Part 331: Specification for metal oxide varistors (MOV)
    IEC 60747-5-5:2007+AMD1:2013 CSV Semiconductor devices - Discrete devices - Part 5-5: Optoelectronic devices - Photocouplers
    IEC 60086-5:2016 Primary batteries - Part 5: Safety of batteries with aqueous electrolyte
    IEC 62133 : 2.0EN+(REDLINE+VERSION) SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SAFETY REQUIREMENTS FOR PORTABLE SEALED SECONDARY CELLS, AND FOR BATTERIES MADE FROM THEM, FOR USE IN PORTABLE APPLICATIONS
    IEC 60695-10-2:2014 FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD
    IEC 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508)
    IEC 60086-4:2014 Primary batteries - Part 4: Safety of lithium batteries
    ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
    IEC 60317-43:1997+AMD1:2010 CSV Specifications for particular types of winding wires - Part 43: Aromatic polyimide type wrapped round copper wire, class 240
    IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
    IEC 61204-7:2016 EXV LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS
    IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
    IEC 61959:2004 SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - MECHANICAL TESTS FOR SEALED PORTABLE SECONDARY CELLS AND BATTERIES
    IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
    IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements
    AS/NZS 3112:2017 Approval and test specification - Plugs and socket-outlets
    ISO 178:2010 Plastics Determination of flexural properties
    IEC 62281 : 3.0 SAFETY OF PRIMARY AND SECONDARY LITHIUM CELLS AND BATTERIES DURING TRANSPORT
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    IEC 61051-1:2007 Varistors for use in electronic equipment - Part 1: Generic specification
    IEC 62485-2:2010 Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
    IEC 60990:2016 Methods of measurement of touch current and protective conductor current
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective