• IEC GUIDE 111:2004

    Current The latest, up-to-date edition.

    Electrical high-voltage equipment in high-voltage substations - Common recommendations for product standards

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  English

    Published date:  21-07-2004

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Reference documents
    3 Guidance for the "Normative references" clause in product
       standards
    4 Guidance for the "Definitions" clause in product standards
    5 Environmental conditions
       5.1 General
       5.2 Normal environmental conditions
       5.3 Special environmental conditions
    6 Ratings
       6.1 General
       6.2 Highest voltage for equipment
       6.3 Rated insulation levels
       6.4 Rated frequency
       6.5 Rated current
       6.6 Rated short-time withstand current
       6.7 Rated peak withstand current
       6.8 Rated duration of short circuit
       6.9 Rated supply voltage of auxiliary and control circuits
       6.10 Rated supply frequency of auxiliary and control
            circuits
    7 Design and construction
       7.1 Requirements for liquids and gases in equipment
       7.2 Earthing of equipment
       7.3 Low-voltage part of equipment
       7.4 Marking
       7.5 Degrees of protection by enclosures
       7.6 Creepage distances
       7.7 Fire hazard
       7.8 Noise level
       7.9 Electromagnetic compatibility (EMC)
       7.10 Mechanical stresses on terminals
       7.11 Interfaces
    8 Tests
       8.1 General
       8.2 Type tests
       8.3 Routine tests
       8.4 Special tests
       8.5 Sample tests
       8.6 Commissioning tests
    9 Rules for transport, storage, erection, operation and
       maintenance
    10 Safety
       10.1 General
       10.2 Electrical aspects
       10.3 Mechanical aspects
       10.4 Thermal aspects
       10.5 Operation aspects
    11 Effects of product standards on the natural environment
    12 Guide for the selection of equipment according to use
    13 Information to be given with enquiries, tenders and orders
    Annex A Identification of test specimens

    Abstract - (Show below) - (Hide below)

    Horizontal publication giving guidance for the harmonization of product and system standards within substations where the highest voltage for equipment is higher than 1 kV. Contains recommendations for common specifications for all HV substation product standards, each of which is augmented by the technical background specific to each TC, which naturally retains freedom in its technical choices. For use by TCs involved in high-voltage (HV) substation systems, such as TCs 13, 14, 17, 20, 22, 28, 32, 33, 36, 37, 38, 57, 95 and 99.

    General Product Information - (Show below) - (Hide below)

    Committee ACTAD
    Document Type Guide
    Publisher International Electrotechnical Committee
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    CEI EN 61109 : 2009 INSULATORS FOR OVERHEAD LINES - COMPOSITE SUSPENSION AND TENSION INSULATORS FOR A/C/ SYSTEMS WITH A NOMINAL VOLTAGE GREATER THAN 1 000 V - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA
    CEI EN 61952 : 2009 INSULATORS FOR OVERHEAD LINES - COMPOSITE LINE POST INSULATORS FOR A.C. SYSTEMS WITH A NOMINAL VOLTAGE GREATER THAN 1000 V - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA
    BS EN 61109:2008 (published 2009-03) Insulators for overhead lines. Composite suspension and tension insulators for a.c. systems with a nominal voltage greater than 1000 V. Definitions, test methods and acceptance criteria
    EN 61952:2008 Insulators for overhead lines - Composite line post insulators for A.C. systems with a nominal voltage greater than 1 000 V - Definitions, test methods and acceptance criteria
    IEC 60137:2017 Insulated bushings for alternating voltages above 1000 V
    BS EN 60137 : 2017 INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1000 V
    IEC 60137:2017 RLV Insulated bushings for alternating voltages above 1000 V
    UNE-EN 60137:2011 Insulated bushings for alternating voltages above 1 000 V
    04/30111589 DC : 0
    IEC TS 63014-1:2018 High voltage direct current (HVDC) power transmission - System requirements for DC-side equipment - Part 1: Using line-commutated converters
    EN 60137:2017 INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1000 V (IEC 60137:2017)
    IEC 61952:2008 Insulators for overhead lines - Composite line post insulators for A.C. systems with a nominal voltage greater than 1 000 V - Definitions, test methods and acceptance criteria
    BS EN 61952:2008 (published 2009-03) Insulators for overhead lines. Composite line post insulators for A.C. systems with a nominal voltage greater than 1000 V. Definitions, test methods and acceptance criteria
    16/30318517 DC : 0 BS EN 60137 ED. 7.0 - INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1000 V
    I.S. EN 61952:2008 INSULATORS FOR OVERHEAD LINES - COMPOSITE LINE POST INSULATORS FOR A.C. SYSTEMS WITH A NOMINAL VOLTAGE GREATER THAN 1 000 V - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA
    I.S. EN 61109:2008 INSULATORS FOR OVERHEAD LINES - COMPOSITE SUSPENSION AND TENSION INSULATORS FOR A.C. SYSTEMS WITH A NOMINAL VOLTAGE GREATER THAN 1 000 V - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA
    IEC 61109:2008 Insulators for overhead lines - Composite suspension and tension insulators for a.c. systems with a nominal voltage greater than 1 000 V - Definitions, test methods and acceptance criteria
    I.S. EN 60137:2017 INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1000 V
    CEI EN 60137 : 2009 INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1000 V
    IEC 60137 REDLINE : 7ED 2017 INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1000 V
    EN 61109 : 2008 INSULATORS FOR OVERHEAD LINES - COMPOSITE SUSPENSION AND TENSION INSULATORS FOR A.C. SYSTEMS WITH A NOMINAL VOLTAGE GREATER THAN 1000 V - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC GUIDE 109:2012 Environmental aspects - Inclusion in electrotechnical product standards
    IEC 60480:2004 Guidelines for the checking and treatment of sulfur hexafluoride (SF6) taken from electrical equipment and specification for its re-use
    IEC 60038:2009 IEC standard voltages
    IEC 60721-1:1990+AMD1:1992+AMD2:1995 CSV Classification of environmental conditions - Part 1: Environmental parameters and their severities
    IEC 60068-2-18:2017 Environmental testing - Part 2-18: Tests - Test R and guidance: Water
    IEC 60826:2017 Design criteria of overhead transmission lines
    IEC 62155:2003 Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V
    IEC 60376:2005 Specification of technical grade sulfur hexafluoride (SF6) for use in electrical equipment
    IEC 60027-1:1992 Letters symbols to be used in electrical technology - Part 1: General
    IEC 60694:1996+AMD1:2000+AMD2:2001 CSV Common specifications for high-voltage switchgear and controlgear standards
    IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
    IEC 60721-2-2:2012 Classification of environmental conditions - Part 2-2: Environmental conditions appearing in nature - Precipitation and wind
    IEC 60721-2-6:1990 Classification of environmental conditions. Part 2: Environmental conditions appearing in nature. Earthquake vibration and shock
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC TS 61000-6-5:2001 Electromagnetic compatibility (EMC) - Part 6-5: Generic standards - Immunity for power station and substation environments
    ISO 1996-1:2016 Acoustics Description, measurement and assessment of environmental noise Part 1: Basic quantities and assessment procedures
    IEC TR 60943:1998+AMD1:2008 CSV Guidance concerning the permissible temperature rise for parts of electrical equipment, in particular for terminals
    IEC 60867:1993 Insulating liquids - Specifications for unused liquids based on synthetic aromatic hydrocarbons
    IEC 60071-2:1996 Insulation co-ordination - Part 2: Application guide
    IEC 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
    CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
    IEC 60721-2-4:1987+AMD1:1988 CSV Classification of environmental conditions - Part 2-4: Environmental conditions appearing in nature - Solar radiation and temperature
    IEC 60059:1999+AMD1:2009 CSV IEC standard current ratings
    IEC 61180-1:1992 High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements
    IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
    IEC 60071-1:2006+AMD1:2010 CSV Insulation co-ordination - Part 1: Definitions, principles and rules
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective