• IEEE C37.118.1-2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    IEEE Standard for Synchrophasor Measurements for Power Systems

    Available format(s):  PDF

    Superseded date:  20-07-2021

    Language(s):  English

    Published date:  28-12-2011

    Publisher:  Institute of Electrical & Electronics Engineers

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. Overview
    2. Normative references
    3. Definitions, acronyms, and abbreviations
    4. Synchrophasor measurement
    5. Synchrophasor measurement requirements and compliance verification
    Annex A (informative) - Bibliography
    Annex B (informative) - Time tagging and dynamic response
    Annex C (informative) - Reference signal processing models
    Annex D (informative) - Time and synchronization communication
    Annex E (informative) - TVE evaluation and PMU testing
    Annex F (informative) - Generator voltage and power angle measurement

    Abstract - (Show below) - (Hide below)

    Describes a synchronized phasor (synchrophasor), frequency, and rate of change of frequency (ROCOF) measurements. Specifies time tag and synchronization requirements for measurement of all three of these quantities.

    General Product Information - (Show below) - (Hide below)

    Committee Power System Relaying and Control
    Development Note Supersedes IEEE C37.118. (12/2011) Amendment 1 to IEEE C37.118.1 is available separately, see IEEE C37.118.1A. (05/2014)
    Document Type Standard
    Publisher Institute of Electrical & Electronics Engineers
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    IEEE C37.244-2013 IEEE Guide for Phasor Data Concentrator Requirements for Power System Protection, Control, and Monitoring
    IEC TR 61850-90-5:2012 Communication networks and systems for power utility automation - Part 90-5: Use of IEC 61850 to transmit synchrophasor information according to IEEE C37.118
    PD IEC/TR 61850-90-4:2013 Communication networks and systems for power utility automation Network engineering guidelines
    PD IEC/TR 61850-90-5:2012 Communication networks and systems for power utility automation Use of IEC 61850 to transmit synchrophasor information according to IEEE C37.118
    IEEE C37.242-2013 IEEE Guide for Synchronization, Calibration, Testing, and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control
    IEEE C37.248-2017 IEEE Guide for Common Format for Naming Intelligent Electronic Devices (COMDEV)
    IEEE C37.247-2019 IEEE Standard for Phasor Data Concentrators for Power Systems
    IEEE C37.118.2-2011 IEEE Standard for Synchrophasor Data Transfer for Power Systems

    Standards Referencing This Book - (Show below) - (Hide below)

    IEEE 1344-1995 IEEE Standard for Synchrophasors for Power Systems
    IEEE C37.238-2011 IEEE Standard Profile for Use of IEEE 1588 Precision Time Protocol in Power System Applications
    IEEE 115-2009 REDLINE IEEE Guide for Test Procedures for Synchronous Machines Part I—Acceptance and Performance Testing Part II—Test Procedures and Parameter Determination for Dynamic Analysis
    IEEE 754-1985 IEEE Standard for Binary Floating-Point Arithmetic
    IEEE 1012-2012 IEEE Standard for System and Software Verification and Validation
    IEEE 754-2008 REDLINE IEEE Standard for Floating-Point Arithmetic
    IEEE 1588-2008 REDLINE IEEE Standard for a Precision Clock Synchronization Protocol for Networked Measurement and Control Systems
    IEEE/IEC C37.111-2013 REDLINE IEEE/IEC International Standard - Measuring relays and protection equipment - Part 24: Common format for transient data exchange (COMTRADE) for power systems
    • Access your standards online with a subscription


      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective