Skip to content
Please enter a keyword to search

  • ISO 1938-1:2015

    Current The latest, up-to-date edition.

    Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  French, English

    Published date:  26-10-2015

    Publisher:  International Organization for Standardization

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 1938-1:2015 specifies the most important metrological and design characteristics of plain limit gauges of linear size.

    ISO 1938-1:2015 defines the different types of plain limit gauges used to verify linear dimensional specifications associated with linear size.

    ISO 1938-1:2015 also defines the design characteristics and the metrological characteristics for these limit gauges as well as the new or wear limits state Maximum Permissible Limits (MPLs) for the new state or wear limits state for these metrological characteristics.

    In addition, ISO 1938-1:2015 describes the use of limit gauges. It covers linear sizes up to 500 mm.

    General Product Information - (Show below) - (Hide below)

    Committee ISO/TC 213
    Development Note Supersedes ISO/DIS 1938-1 & ISO R 1938. (10/2015)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    I.S. EN ISO 1938-2:2017 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 2: REFERENCE DISK GAUGES (ISO 1938-2:2017)
    16/30333694 DC : 0 BS EN ISO 14253-1 - GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - PART 1: DECISION RULES FOR VERIFYING CONFORMITY OR NONCONFORMITY WITH SPECIFICATIONS
    ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
    DIN ISO 3547-5:2015-12 PLAIN BEARINGS - WRAPPED BUSHES - PART 5: CHECKING THE OUTSIDE DIAMETER (ISO 3547-5:2007)
    EN ISO 14253-1:2017 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for verifying conformity or nonconformity with specifications (ISO 14253-1:2017)
    BS EN ISO 1938-2:2017 Geometrical product specifications (GPS). Dimensional measuring equipment Reference disk gauges
    DIN EN ISO 14638 E : 2015 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - MATRIX MODEL (ISO 14638:2015)
    DIN ISO 3547-5:2015-12 PLAIN BEARINGS - WRAPPED BUSHES - PART 5: CHECKING THE OUTSIDE DIAMETER (ISO 3547-5:2007)
    BS EN ISO 17296-3:2016 Additive manufacturing. General principles Main characteristics and corresponding test methods
    DIN EN ISO 14638:2015-12 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - MATRIX MODEL (ISO 14638:2015)
    I.S. EN ISO 14253-1:2017 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - PART 1: DECISION RULES FOR VERIFYING CONFORMITY OR NONCONFORMITY WITH SPECIFICATIONS (ISO 14253-1:2017)
    EN ISO 17296-3:2016 Additive manufacturing - General principles - Part 3: Main characteristics and corresponding test methods (ISO 17296-3:2014)
    EN ISO 1938-2:2017 Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 2: Reference disk gauges (ISO 1938-2:2017)
    DIN EN ISO 1938-2 E : 2017 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 2: REFERENCE DISK GAUGES (ISO 1938-2:2017)
    DIN EN ISO 1938-2:2017-05 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 2: REFERENCE DISK GAUGES (ISO 1938-2:2017)
    BS ISO 199:2014 Rolling bearings. Thrust bearings. Geometrical product specification (GPS) and tolerance values
    ISO 11540:2014 Writing and marking instruments Specification for caps to reduce the risk of asphyxiation
    UNE-EN ISO 17296-3:2017 Additive manufacturing - General principles - Part 3: Main characteristics and corresponding test methods (ISO 17296-3:2014)
    ISO 1938-2:2017 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
    ISO 14638:2015 Geometrical product specifications (GPS) Matrix model
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    ISO 14978:2006 Geometrical product specifications (GPS) General concepts and requirements for GPS measuring equipment
    ISO 1:2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties
    ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
    ISO 17450-1:2011 Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
    ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
    ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
    ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
    ISO 17450-2:2012 Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities
    ISO 14405-1:2016 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
    ISO 14253-2:2011 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
    ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective