ISO/IEC 13239:2002
Current
The latest, up-to-date edition.
Information technology Telecommunications and information exchange between systems High-level data link control (HDLC) procedures
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
22-08-2002
This International Standard specifies the frame structures, the elements of procedures, the classes of procedures, the content
and format of the general purpose Exchange Identification (XID) frame, and a means for resolution/negotiation of a data link
layer address in switched environments for data communication systems using bit-oriented high-level data link control
(HDLC) procedures.
NOTE The use of the phrase "bit-oriented", referring to the HDLC control procedures, pertains to the allocation of a non-integral number
of bits to various subfields used for HDLC control purposes. However, the frame as an entirety may be constructed from octet-oriented units
(e.g., start-stop mode) for transmission purposes.
The frame structure portion defines the relative positions of the various components of the basic frame format and the nonbasic
frame format. The mechanisms used to achieve bit pattern independence (transparency), where and when required, within
the frame are also defined. In addition, three frame checking sequences (FCS) are specified; the rules for address field
extension are defined; and the addressing conventions available are described.
The elements of procedures portion specifies elements of data link control procedures for synchronous or start/stop, codetransparent
data transmission using independent frame numbering in both directions.
These HDLC elements of procedures are defined specifically in terms of the actions that occur on receipt of commands at a
secondary station, a tributary station, a peer station, or a combined station.
This International Standard is intended to cover a wide range of applications; for example one-way, two-way alternate or twoway
simultaneous data communication between data stations which are usually buffered, including operations on different
types of data circuits; for example multipoint/point-to-point, duplex/half-duplex, switched/non-switched, synchronous/startstop,
etc.
The defined elements of procedures are to be considered as a common basis for establishing different types of data link control
procedures. This International Standard does not define any single system and should not be regarded as a specification for a
data communication system. Not all of the commands or responses are required for any particular system implementation.
The classes of procedures portion describes the HDLC unbalanced classes of procedures, the HDLC balanced class of
procedures, and the HDLC connectionless classes of procedures for synchronous or start/stop data transmission.
For the unbalanced classes, the data link consists of a primary station plus one or more secondary stations and operates in
either the normal response mode or the asynchronous response mode in a point-to-point or multipoint configuration. For the
balanced class, the data link consists of two combined stations and operates in the asynchronous balanced mode in a point-topoint
configuration. For the unbalanced connectionless class, the data link consists of a control station plus one or more
tributary stations and operates in the unbalanced connectionless-mode in a point-to-point or multipoint configuration. For the
balanced connectionless class, the data link consists of two peer stations and operates in the balanced connectionless-mode in a
point-to-point configuration. In each class, a basic repertoire of commands and responses is defined, but the capability of the
data link may be modified by the use of optional functions.
Balanced operation is intended for use in circumstances which require equal control at either end of the data link. Operational
requirements are covered in accordance with the overall HDLC architecture.
The content and format of the Exchange Identification (XID) frame portion builds on the fact that the principal use of the XID
frame is to exchange data link information between two or more HDLC stations. For the purpose of this International Standard,
ISO/IEC 13239:2002(E)
2 ISO/IEC 2002 ? All rights reserved
data link information shall include any and all essential operational characteristics such as identification, authentication and/or
selection of optional functions and facilities concerning each station. This International Standard defines a single-exchange
negotiation procedure for establishing operational characteristics when either one or more stations are capable of providing
multiple selections.
This International Standard provides a means for exchanging the necessary information to establish, at a minimum, a data link
connection between two correspondents wishing to communicate. It describes a general purpose XID frame information field
content and format for that purpose.
It defines encoding for information related to the basic HDLC standards only. Mechanisms are provided to permit the general
purpose XID frame information field to be used to negotiate private parameters in a single XID exchange simultaneously with
negotiation of the defined basic parameters.
This International Standard does not limit or restrict the use of the XID frame information field from defining other standard
formats for use in specific applications.
The following are examples of potential uses of the XID command/response frame interchange:
a) Identification of the calling and called stations when using circuit switched networks (including switched network backup
applications).
b) Identification of stations operating on non-switched networks requiring identification at start-up.
c) The XID command frame with an individual, group or all-station address may be used to solicit XID response frame(s)
from other station(s) on the data link, prior to or following data link establishment.
d) Negotiation of the Frame Check Sequence (FCS) to be used for subsequent information interchange, by stations that
support both 16-bit FCS and 32-bit FCS capabilities.
e) Convey higher layer information that may be required prior to data link establishment.
f) Transmission of an XID response frame at any respond opportunity to request an XID exchange to modify some of the
operational parameters (for example, window size) following data link establishment.
g) Negotiation of the number of protected bits in the frame when an Unnumbered Information with Header check (UIH)
frame is used.
The means for resolution/negotiation of a data link layer address in switched environments portion is applicable to data stations
employing HDLC balanced classes of procedures which provide the XID command/response capability with the two specific
parameter fields, identified below. It is used to select a pair of operational link addresses when preassigned, system designated
addresses are not known on an a priori basis; e.g., switched circuited data links. Additional XID frame functions (including the
exchange of operational parameters, command/response support, higher layer information, etc.) may be accomplished in
conjunction with data link layer address determination or following address determination, with additional XID frame
exchanges.
NOTE Address resolution procedures for situations where the remote DTE does not support XID frames, the "all-station"
address, or complete address support capabilities as defined in clause 8 below are not within the scope of this International
Standard.
DevelopmentNote |
Supersedes BS ISO/IEC 13239. (09/2003) Supersedes ISO/IEC 8885, ISO/IEC 4335 and ISO/IEC 13239 (04/2004) Supersedes ISO/IEC 3309. (02/2010)
|
DocumentType |
Standard
|
Pages |
128
|
PublisherName |
International Organization for Standardization
|
Status |
Current
|
Supersedes |
Standards | Relationship |
NEN ISO/IEC 13239 : 2002 | Identical |
CAN/CSA-ISO/IEC 13239-04 (R2012) | Identical |
CSA ISO/IEC 13239 : 2004 | Identical |
CEI EN 61375-3-1 : 2013 | ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK (TCN) - PART 3-1: MULTIFUNCTION VEHICLE BUS (MVB) |
17/30359080 DC : 0 | BS ISO/IEC 12034-1 - INFORMATION TECHNOLOGY - ARCHIVE EXCHANGE FORMAT (AXF) - PART 1: STRUCTURE AND SEMANTICS |
BS ISO/IEC 18000-3:2010 | Information technology. Radio frequency identification for item management Parameters for air interface communications at 13,56 MHz |
TS 102 694-1 : 10.2.0 | SMART CARDS; TEST SPECIFICATION FOR THE SINGLE WIRE PROTOCOL (SWP) INTERFACE; PART 1: TERMINAL FEATURES (RELEASE 10) |
CSA ISO/IEC 14443-3 : 2018 | IDENTIFICATION CARDS - CONTACTLESS INTEGRATED CIRCUIT CARDS - PROXIMITY CARDS - PART 3: INITIALIZATION AND ANTICOLLISION |
16/30339535 DC : 0 | BS EN 62056-5-3 ED 3.0 - ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 5-3: DLMS/COSEM APPLICATION LAYER |
BS ISO/IEC 7816-3:2006 | Identification cards. Integrated circuit cards Cards with contacts. Electrical interface and transmission protocols |
IS/IEC/TS 62351 : Part 6 : 2007(R2016) | Power Systems Management and Associated Information Exchange Data and Communication Security Part 6 Security for IEC 61850<br> |
10/30239388 DC : 0 | BS EN ISO/IEC 62056-6-2 - ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 6-2: COSEM INTERFACE CLASSES |
INCITS/ISO/IEC 15693-3 : 2001 | IDENTIFICATION CARDS - CONTACTLESS INTEGRATED CIRCUIT(S) CARDS - VICINITY CARDS - PART 3: ANTICOLLISION AND TRANSMISSION PROTOCOL |
CSA ISO/IEC 14165-241:2006(R2016) | INFORMATION TECHNOLOGY - FIBRE CHANNEL - PART 241: BACKBONE 2 (FC-BB-2) |
IEEE 1703-2012 | IEEE Standard for Local Area Network/Wide Area Network (LAN/WAN) Node Communication Protocol to Complement the Utility Industry End Device Data Tables |
ISO/IEC 12034-1:2017 | Information technology — Archive eXchange Format (AXF) — Part 1: Structure and semantics |
CEI EN 61158-4-16 : 2008 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-16: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 16 ELEMENTS |
I.S. EN 61158-4-24:2014 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-24: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 24 ELEMENTS |
I.S. EN 62056-21:2002 | ELECTRICITY METERING - DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL - PART 21: DIRECT LOCAL DATA EXCHANGE |
INCITS/ISO/IEC 15693-3 : 2001 : R2006 | IDENTIFICATION CARDS - CONTACTLESS INTEGRATED CIRCUIT(S) CARDS - VICINITY CARDS - PART 3: ANTICOLLISION AND TRANSMISSION PROTOCOL |
EN 301 841-2 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); VHF AIR-GROUND DIGITAL LINK (VDL) MODE 2; TECHNICAL CHARACTERISTICS AND METHODS OF MEASUREMENT FOR GROUND-BASED EQUIPMENT; PART 2: UPPER LAYERS |
I.S. EN 62056-46:2002 | ELECTRICITY METERING - DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL - PART 46: DATA LINK LAYER USING HDLC PROTOCOL |
NF EN 301841-2 : 2004 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - VHF AIR-GROUND DIGITAL LINK (VDL) MODE 2 - TECHNICAL CHARACTERISTICS AND METHODS OF MEASUREMENT FOR GROUND-BASED EQUIPMENT - PART 2: UPPER LAYERS |
IEC 61158-4-18:2010 | Industrial communication networks - Fieldbus specifications - Part 4-18: Data-link layer protocol specification - Type 18 elements |
EN 62056-46:2002/A1:2007 | ELECTRICITY METERING - DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL - PART 46: DATA LINK LAYER USING HDLC PROTOCOL |
IEC 62320-2:2016 RLV | Maritime navigation and radiocommunication equipment and systems - Automatic identification system (AIS) - Part 2: AIS AtoN Stations - Operational and performance requirements, methods of testing and required test results |
IEC 62056-5-3:2016 RLV | Electricity metering data exchange - The DLMS/COSEM suite - Part 5-3: DLMS/COSEM application layer |
EN 61158-4-18:2012 | Industrial communication networks - Fieldbus specifications - Part 4-18: Data-link layer protocol specification - Type 18 elements |
EN 62056-53:2007 | Electricity metering - Data exchange for meter reading, tariff and load control - Part 53: COSEM application layer |
EN 62056-5-3:2017 | Electricity metering data exchange - The DLMS/COSEM suite - Part 5-3: DLMS/COSEM application layer |
EN 61158-4-24:2014 | Industrial communication networks - Fieldbus specifications - Part 4-24: Data-link layer protocol specification - Type 24 elements |
EN 61375-2-1 : 2012 | ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK (TCN) - PART 2-1: WIRE TRAIN BUS (WTB) (IEC 61375-2-1:2012) |
07/30164285 DC : 0 | BS ISO/IEC 15693-3 - IDENTIFICATION CARDS - CONTACTLESS INTEGRATED CIRCUIT(S) CARDS - VICINITY CARDS - PART 3: ANTICOLLISION AND TRANSMISSION PROTOCOL |
CAN/CSA-ISO/IEC 18000-63:16 | Information technology Radio frequency identification for item management Part 63: Parameters for air interface communications at 860 MHz to 960 MHz Type C (Adopted ISO/IEC 18000-63:2015, second edition, 2015-10-15) |
DD IEC/TS 62351-6:2007 | Power systems management and associated information exchange. Data and communication security Security for IEC 61850 profiles |
BS EN 62056-5-3:2017 | Electrcity metering data exchange. The DLMS/COSEM suite DLMS/COSEM application layer |
14/30314819 DC : 0 | BS EN 62320-2 - MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS - AUTOMATIC IDENTIFICATION SYSTEM (AIS) - PART 2: AIS ATON STATIONS - OPERATIONAL AND PERFORMANCE REQUIREMENTS, METHODS OF TESTING AND REQUIRED TEST RESULTS |
CSA ISO/IEC 18000-3 : 2012 | INFORMATION TECHNOLOGY - RADIO FREQUENCY IDENTIFICATION FOR ITEM MANAGEMENT - PART 3: PARAMETERS FOR AIR INTERFACE COMMUNICATIONS AT 13,56 MHZ |
TS 101 524 : 1.5.1 | ACCESS, TERMINALS, TRANSMISSION AND MULTIPLEXING (ATTM); ACCESS TRANSMISSION SYSTEM ON METALLIC ACCESS CABLES; SYMMETRIC SINGLE PAIR HIGH BITRATE DIGITAL SUBSCRIBER LINE (SDSL) |
BS EN 61158-4-18:2012 | Industrial communication networks. Fieldbus specifications Data-link layer protocol specification. Type 18 elements |
BS EN 61158-4-16:2008 | Industrial communication networks. Fieldbus specifications Data-link layer protocol specification. Type 16 elements |
BS ISO/IEC 12034-1:2017 | Information technology. Archive eXchange Format (AXF) Structure and semantics |
BS EN 62056-53:2007 | Electricity metering. Data exchange for meter reading, tariff and load control COSEM application layer |
IEEE 802.2 : 1998 | INFORMATION TECHNOLOGY - TELECOMMUNICATIONS AND INFORMATION EXCHANGE BETWEEN SYSTEMS - LOCAL AND METROPOLITAN AREA NETWORKS - SPECIFIC REQUIREMENTS - PART 2: LOGICAL LINK CONTROL |
09/30189756 DC : 0 | BS ISO/IEC 18000-3-2 - INFORMATION TECHNOLOGY - RADIO FREQUENCY IDENTIFICATION FOR ITEM MANAGEMENT - PART 3: PARAMETERS FOR AIR INTERFACE COMMUNICATIONS AT 13,56 MHZ |
11/30242642 DC : 0 | BS EN 62056-5-3 - ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 5-3: DLMS/COSEM APPLICATION LAYER |
CEI EN 62056-7-5 : 1ED 2017 | ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 7-5: LOCAL DATA TRANSMISSION PROFILES FOR LOCAL NETWORKS (LN) |
12/30259441 DC : 0 | BS EN 13757-1 - COMMUNICATION SYSTEM FOR AND REMOTE READING OF METERS - PART 1: DATA EXCHANGE |
CAN/CSA-ISO/IEC 7816-3-07 (R2017) | Identification Cards - Integrated Circuit Cards - Part 3: Cards with Contacts - Electrical Interface and Transmission Protocols (Adopted ISO/IEC 7816-3:2006, third edition, 2006-11-01) |
BS ISO/IEC 8802-2:1998 | Information technology. Telecommunications and information exchange between systems. Local and metropolitan area networks. Specific requirements Logical link control |
DIN EN 61158-4-18:2013-01 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-18: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 18 ELEMENTS (IEC 61158-4-18:2010) |
BS ISO/IEC 15693-3 : 2009 | IDENTIFICATION CARDS - CONTACTLESS INTEGRATED CIRCUIT CARDS - VICINITY CARDS - PART 3: ANTICOLLISION AND TRANSMISSION PROTOCOL |
ISO/IEC 14443-4:2016 | Identification cards Contactless integrated circuit cards Proximity cards Part 4: Transmission protocol |
ISO/IEC TR 10171:2000 | Information technology Telecommunications and information exchange between systems List of standard data link layer protocols that utilize high-level data link control (HDLC) classes of procedures, list of standard XID format identifiers, list of standard mode-setting information field format identifiers, and list of standard user-defined parameter set identification values |
CSA ISO/IEC TR 24729-1 : 2014 | INFORMATION TECHNOLOGY - RADIO FREQUENCY IDENTIFICATION FOR ITEM MANAGEMENT - IMPLEMENTATION GUIDELINES - PART 1: RFID-ENABLED LABELS AND PACKAGING SUPPORTING ISO/IEC 18000-6C |
ISO/IEC 18000-63:2015 | Information technology Radio frequency identification for item management Part 63: Parameters for air interface communications at 860 MHz to 960 MHz Type C |
ISO/IEC 8802-2:1998 | Information technology Telecommunications and information exchange between systems Local and metropolitan area networks Specific requirements Part 2: Logical link control |
ISO/IEC 14443-3:2016 | Identification cards Contactless integrated circuit cards Proximity cards Part 3: Initialization and anticollision |
PREN 13757-1 : DRAFT 2012 | COMMUNICATION SYSTEM FOR AND REMOTE READING OF METERS - PART 1: DATA EXCHANGE |
DIN EN 13757-1:2015-01 | Communication systems for meters - Part 1: Data exchange |
TS 102 225 : 12.1.0 | SMART CARDS; SECURED PACKET STRUCTURE FOR UICC BASED APPLICATIONS (RELEASE 12) |
I.S. EN 13757-1:2014 | COMMUNICATION SYSTEMS FOR METERS - PART 1: DATA EXCHANGE |
ONORM EN 13757-1 : 2014 | COMMUNICATION SYSTEMS FOR METERS - PART 1: DATA EXCHANGE |
ANSI C12.21:2006 (R2016) | American National Standard for Protocol Specification for Telephone Modem Communication |
ANSI C12.18:2006(R2016) | American National Standard for Protocol Specification for ANSI Type 2 Optical Port |
I.S. EN 61375-2-1:2012 | ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK (TCN) - PART 2-1: WIRE TRAIN BUS (WTB) (IEC 61375-2-1:2012 (EQV)) |
BS EN 62056-46:2002 | Electricity metering. Data exchange for meter reading, tariff and load control Data link layer using HDLC protocol |
BS EN 61158-5-15:2012 | Industrial communication networks. Fieldbus specifications Application layer service definition. Type 15 elements |
UNI 10607-2 : 2013 | ROAD TRAFFIC AND TRANSPORT TELEMATICS - AUTOMATIC DYNAMIC DEBITING SYSTEMS AND AUTOMATIC ACCESS CONTROL SYSTEMS USING DEDICATED SHORT-RANGE COMMUNICATION AT 5,8 GHZ - PART 2: DATA LINK LAYER |
BS EN 62056-21:2002 | Electricity metering. Data exchange for meter reading, tariff and load control Direct local data exchange |
GS ORI 002-2 : 4.1.1 | OPEN RADIO EQUIPMENT INTERFACE (ORI); ORI INTERFACE SPECIFICATION; PART 2: CONTROL AND MANAGEMENT (RELEASE 4) |
NF EN 62056-7-5 : 2017 | ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 7-5: LOCAL DATA TRANSMISSION PROFILES FOR LOCAL NETWORKS (LN) |
09/30205454 DC : 0 | BS EN 61375-3-1 - ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK - PART 3-1: MVB - MULTIPURPOSE VEHICLE BUS |
CEI EN 62056-21 : 2003 | ELECTRICITY METERING - DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL PART 21: DIRECT LOCAL DATA EXCHANGE |
BS EN 61375-3-1:2012 | Electronic railway equipment. Train communication network (TCN) Multifunction Vehicle Bus (MVB) |
CSA ISO/IEC 7816-3 : 2007 : R2012 | IDENTIFICATION CARDS - INTEGRATED CIRCUIT CARDS - PART 3: CARDS WITH CONTACTS - ELECTRICAL INTERFACE AND TRANSMISSION PROTOCOLS |
BS ISO/IEC 14443-4 : 2016 | IDENTIFICATION CARDS - CONTACTLESS INTEGRATED CIRCUIT CARDS - PROXIMITY CARDS - PART 4: TRANSMISSION PROTOCOL |
CSA ISO/IEC 14165-241 : 2006 | INFORMATION TECHNOLOGY - FIBRE CHANNEL - PART 241: BACKBONE 2 (FC-BB-2) |
BS ISO/IEC 14443-3 : 2016 | IDENTIFICATION CARDS - CONTACTLESS INTEGRATED CIRCUIT CARDS - PROXIMITY CARDS - PART 3: INITIALIZATION AND ANTICOLLISION |
TS 102 613 : 11.0.0 | SMART CARDS; UICC - CONTACTLESS FRONT-END (CLF) INTERFACE; PART 1: PHYSICAL AND DATA LINK LAYER CHARACTERISTICS (RELEASE 11) |
ISO/IEC 14165-243:2012 | Information technology Fibre Channel Part 243: Backbone 3 (FC-BB-3) |
ISO/IEC 18000-3:2010 | Information technology — Radio frequency identification for item management — Part 3: Parameters for air interface communications at 13,56 MHz |
CEI EN 61158-4-24 : 2016 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-24: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 24 ELEMENTS |
I.S. EN 62056-53:2007 | ELECTRICITY METERING - DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL - PART 53: COSEM APPLICATION LAYER |
I.S. EN 61158-4-16:2008 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-16: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 16 ELEMENTS |
ISO/IEC 7816-3:2006 | Identification cards — Integrated circuit cards — Part 3: Cards with contacts — Electrical interface and transmission protocols |
IEC 62056-53:2006 | Electricity metering - Data exchange for meter reading, tariff and load control - Part 53: COSEM application layer |
IEC 62056-7-5:2016 | Electricity metering data exchange - The DLMS/COSEM suite - Part 7-5: Local data transmission profiles for Local Networks (LN) |
IEC 61158-4-16:2007 | Industrial communication networks - Fieldbus specifications - Part 4-16: Data-link layer protocol specification - Type 16 elements |
EN 62320-2:2017 | MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS - AUTOMATIC IDENTIFICATION SYSTEM (AIS) - PART 2: AIS ATON STATIONS - OPERATIONAL AND PERFORMANCE REQUIREMENTS, METHODS OF TESTING AND REQUIRED TEST RESULTS (IEC 62320-2:2016) |
CEI EN 61375-2-1 : 2013 | ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK (TCN) - PART 2-1: WIRE TRAIN BUS (WTB) |
14/30299394 DC : 0 | BS ISO/IEC 18000-63 - INFORMATION TECHNOLOGY - RADIO FREQUENCY IDENTIFICATION FOR ITEM MANAGEMENT - PART 63: PARAMETERS FOR AIR INTERFACE COMMUNICATIONS AT 860 MHZ TO 960 MHZ TYPE C |
ISO/IEC 15693-3:2009 | Identification cards Contactless integrated circuit cards Vicinity cards Part 3: Anticollision and transmission protocol |
TS 101 369 : 7.2.0 | DIGITAL CELLULAR TELECOMMUNICATIONS SYSTEM (PHASE 2+); TERMINAL EQUIPMENT TO MOBILE STATION (TE-MS) MULTIPLEXER PROTOCOL |
BS ISO/IEC 18000-63:2015 | Information technology. Radio frequency identification for item management Parameters for air interface communications at 860 MHz to 960 MHz Type C |
08/30164282 DC : 0 | BS ISO/IEC 14443-3 - IDENTIFICATION CARDS - CONTACT LESS INTEGRATED CIRCUIT(S) CARDS - PROXIMITY CARDS - PART 3: INITIALIZATION AND ANTICOLLISION |
09/30205446 DC : 0 | BS EN 61375-2-1 - ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK - PART 2-1: WTB - WIRE TRAIN BUS |
TS 125 463 : 7.5.0 | UNIVERSAL MOBILE TELECOMMUNICATIONS SYSTEM (UMTS); UTRAN IUANT INTERFACE: REMOTE ELECTRICAL TILTING (RET) ANTENNAS APPLICATION PART (RETAP) SIGNALLING |
DIN EN 61158-4-16:2008-09 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-16: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 16 ELEMENTS |
05/30141122 DC : DRAFT OCT 2005 | ISO 15745-5 - INDUSTRIAL AUTOMATION SYSTEMS AND INTEGRATION - OPEN SYSTEMS APPLICATION INTEGRATION FRAMEWORK - PART 5: REFERENCE DESCRIPTION FOR HDLC-BASED CONTROL SYSTEMS |
BS EN 61375-2-1:2012 | Electronic railway equipment. Train communication network (TCN) Wire Train Bus (WTB) |
TR 103 380 : 1.0.0 | SMART CARDS; TECHNICAL REPORT TO IMPROVE TEST EQUIPMENT INTEGRITY (RELEASE INDEPENDENT) |
EN 300 674-3-1 : 3.0.0 DRAFT | INTELLIGENT TRANSPORT SYSTEMS (ITS); ROAD TRANSPORT AND TRAFFIC TELEMATICS (RTTT); DEDICATED SHORT RANGE COMMUNICATIONS (DSRC); PART 3-1: TECHNICAL CHARACTERISTICS AND TEST METHODS FOR HIGH DATA RATE (HDR) DATA TRANSMISSION EQUIPMENT OPERATING IN THE 5,8 GHZ INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) BAND |
NF EN 301842-2 : 2015 | VHF AIR-GROUND DIGITAL LINK (VDL) MODE 4 RADIO EQUIPMENT - TECHNICAL CHARACTERISTICS AND METHODS OF MEASUREMENT FOR GROUND-BASED EQUIPMENT - PART 2: GENERAL DESCRIPTION AND DATA LINK LAYER (V1.7.1) |
BS EN 61158-4-24:2014 | Industrial communication networks. Fieldbus specifications Data-link layer protocol specification. Type 24 elements |
BIS IS/IEC 62056-53 : 2006 | ELECTRICITY METERING - DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL - PART 53: COSEM APPLICATION LAYER |
IEC TS 62351-6:2007 | Power systems management and associated information exchange - Data and communications security - Part 6: Security for IEC 61850 |
IEEE 1702-2011 | IEEE Standard for Telephone Modem Communication Protocol to Complement the Utility Industry End Device Data Tables |
ISO/IEC 14165-241:2005 | Information technology Fibre Channel Part 241: Backbone 2 (FC-BB-2) |
TS 125 462 : 13.0.0 | UNIVERSAL MOBILE TELECOMMUNICATIONS SYSTEM (UMTS); UTRAN IUANT INTERFACE: SIGNALLING TRANSPORT (3GPP TS 25.462 VERSION 13.0.0 RELEASE 13) |
TS 125 460 : 13.0.0 | UNIVERSAL MOBILE TELECOMMUNICATIONS SYSTEM (UMTS); UTRAN IUANT INTERFACE: GENERAL ASPECTS AND PRINCIPLES (3GPP TS 25.460 VERSION 13.0.0 RELEASE 13) |
TS 102 694-2 : 10.3.0 | SMART CARDS; TEST SPECIFICATION FOR THE SINGLE WIRE PROTOCOL (SWP) INTERFACE; PART 2: UICC FEATURES (RELEASE 10) |
I.S. EN 62320-2:2017 | MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS - AUTOMATIC IDENTIFICATION SYSTEM (AIS) - PART 2: AIS ATON STATIONS - OPERATIONAL AND PERFORMANCE REQUIREMENTS, METHODS OF TESTING AND REQUIRED TEST RESULTS |
CEI EN 61158-4-18 : 2013 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-18: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 18 ELEMENTS |
IEC TR 62051-1:2004 | Electricity metering - Data exchange for meter reading, tariff and load control - Glossary of terms - Part 1: Terms related to data exchange with metering equipment using DLMS/COSEM |
IEC 62056-46:2002+AMD1:2006 CSV | Electricity metering - Data exchange for meter reading, tariff and load control - Part 46: Data link layer using HDLC protocol |
IEC 61375-3-1:2012 | Electronic railway equipment - Train communication network (TCN) - Part 3-1: Multifunction Vehicle Bus (MVB) |
IEC 61375-2-1:2012 | Electronic railway equipment - Train communication network (TCN) - Part 2-1: Wire Train Bus (WTB) |
BS EN 13757-1:2014 | Communication systems for meters Data exchange |
IEC 62320-2:2016 | Maritime navigation and radiocommunication equipment and systems - Automatic identification system (AIS) - Part 2: AIS AtoN Stations - Operational and performance requirements, methods of testing and required test results |
IEC 62056-21:2002 | Electricity metering - Data exchange for meter reading, tariff and load control - Part 21: Direct local data exchange |
UNE-EN 13757-1:2015 | Communication systems for meters - Part 1: Data exchange |
BIS IS/IEC 62056-46 : 2007 | ELECTRICITY METERING - DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL - PART 46: DATA LINK LAYER USING HDLC PROTOCOL |
BS EN 62320-2:2017 | Maritime navigation and radiocommunication equipment and systems. Automatic identification system (AIS) AIS AtoN Stations. Operational and performance requirements, methods of testing and required test results |
BS EN 62056-7-5:2016 | Electricity metering data exchange. The DLMS/COSEM suite Local data transmission profiles for Local Networks (LN) |
14/30302871 DC : 0 | BS EN 62056-7-5 - ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 7-5: COMMUNICATION PROFILES FOR LOCAL DATA TRANSMISSION |
ISO 15745-5:2007 | Industrial automation systems and integration Open systems application integration framework Part 5: Reference description for HDLC-based control systems |
UNI/TS 11291-11-3 : 2014 | Gas measurement systems - Hourly based gas metering systems - Part 11-3: Communication profile of local interface |
CAN/CSA-ISO/IEC 18000-3:12 (R2016) | Information technology - Radio frequency identification for item management - Part 3: Parameters for air interface communications at 13,56 MHz (Adopted ISO/IEC 18000-3:2010, third edition, 2010-11-15) |
I.S. EN 62056-7-5:2016 | ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 7-5: LOCAL DATA TRANSMISSION PROFILES FOR LOCAL NETWORKS (LN) |
ANSI INCITS 414 : 2006 | INFORMATION TECHNOLOGY - FIBRE CHANNEL - BACKBONE - 3 (FC-BB-3) |
I.S. CWA 13987-1:2003 | SMART CARD SYSTEMS: INTEROPERABLE CITIZEN SERVICES: EXTENDED USER RELATED INFORMATION - PART 1: DEFINITION OF USER RELATED INFORMATION AND IMPLEMENTATION |
CSA ISO/IEC 7816-3 : 2007 | IDENTIFICATION CARDS - INTEGRATED CIRCUIT CARDS - PART 3: CARDS WITH CONTACTS - ELECTRICAL INTERFACE AND TRANSMISSION PROTOCOLS |
ANSI INCITS 342 : 2001 | INFORMATION TECHNOLOGY - FIBRE CHANNEL - BACKBONE (FC-BB) |
ES 200 674-1 : 2.4.1 | INTELLIGENT TRANSPORT SYSTEMS (ITS); ROAD TRANSPORT AND TRAFFIC TELEMATICS (RTTT); DEDICATED SHORT RANGE COMMUNICATIONS (DSRC); PART 1: TECHNICAL CHARACTERISTICS AND TEST METHODS FOR HIGH DATA RATE (HDR) DATA TRANSMISSION EQUIPMENT OPERATING IN THE 5,8 GHZ INDUSTRIAL, SCIENTIFIC AND MEDICAL (ISM) BAND |
I.S. EN 62056-5-3:2017 | ELECTRICITY METERING DATA EXCHANGE - THE DLMS/COSEM SUITE - PART 5-3: DLMS/COSEM APPLICATION LAYER |
IEC 62056-5-3:2017 | Electrcity metering data exchange - The DLMS/COSEM suite - Part 5-3: DLMS/COSEM application layer |
TS 101 270-2 : 1.2.1 | TRANSMISSION AND MULTIPLEXING (TM); ACCESS TRANSMISSION SYSTEMS ON METALLIC ACCESS CABLES; VERY HIGH SPEED DIGITAL SUBSCRIBER LINE (VDSL); PART 2: TRANSCEIVER SPECIFICATION |
ISO/IEC TR 24729-1:2008 | Information technology Radio frequency identification for item management Implementation guidelines Part 1: RFID-enabled labels and packaging supporting ISO/IEC 18000-6C |
I.S. EN 61158-4-18:2012 | INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 4-18: DATA-LINK LAYER PROTOCOL SPECIFICATION - TYPE 18 ELEMENTS (IEC 61158-4-18:2010 (EQV)) |
TS 100 392-2 : 3.7.1 | TERRESTRIAL TRUNKED RADIO (TETRA); VOICE PLUS DATA (V+D); PART 2: AIR INTERFACE (AI) |
TS 127 010 : 13.0.0 | DIGITAL CELLULAR TELECOMMUNICATIONS SYSTEM (PHASE 2+) (GSM); UNIVERSAL MOBILE TELECOMMUNICATIONS SYSTEM (UMTS); LTE; TERMINAL EQUIPMENT TO USER EQUIPMENT (TE-UE) MULTIPLEXER PROTOCOL (3GPP TS 27.010 VERSION 14.0.0 RELEASE 14) |
I.S. EN 61375-3-1:2012 | ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK (TCN) - PART 3-1: MULTIFUNCTION VEHICLE BUS (MVB) (IEC 61375-3-1:2012 (EQV)) |
EN 62320-2:2017 | MARITIME NAVIGATION AND RADIOCOMMUNICATION EQUIPMENT AND SYSTEMS - AUTOMATIC IDENTIFICATION SYSTEM (AIS) - PART 2: AIS ATON STATIONS - OPERATIONAL AND PERFORMANCE REQUIREMENTS, METHODS OF TESTING AND REQUIRED TEST RESULTS (IEC 62320-2:2016) |
IEC 61158-5-15:2010 | Industrial communication networks - Fieldbus specifications - Part 5-15: Application layer service definition - Type 15 elements |
EN 13757-1:2014 | Communication systems for meters - Part 1: Data exchange |
EN 62056-21:2002 | Electricity metering - Data exchange for meter reading, tariff and load control - Part 21: Direct local data exchange |
EN 62056-7-5:2016 | Electricity metering data exchange - The DLMS/COSEM suite - Part 7-5: Local data transmission profiles for Local Networks (LN) |
EN 61158-4-16:2008 | Industrial communication networks - Fieldbus specifications - Part 4-16: Data-link layer protocol specification - Type 16 elements |
EN 61375-3-1 : 2012 | ELECTRONIC RAILWAY EQUIPMENT - TRAIN COMMUNICATION NETWORK (TCN) - PART 3-1: MULTIFUNCTION VEHICLE BUS (MVB) (IEC 61375-3-1:2012) |
SAE J3068/1:2023 | Identification of Vehicles and Supply Equipment for Conductive AC Charging |
OVE/ONORM EN 301842-2 : 1.7.1 | VHF AIR-GROUND DIGITAL LINK (VDL) MODE 4 RADIO EQUIPMENT - TECHNICAL CHARACTERISTICS AND METHODS OF MEASUREMENT FOR GROUND-BASED EQUIPMENT - PART 2: GENERAL DESCRIPTION AND DATA LINK LAYER (ETSI EN 301 842-2 V1.7.1 (2015-04) |
ISO/IEC 7498-1:1994 | Information technology Open Systems Interconnection Basic Reference Model: The Basic Model |
ISO/IEC TR 10171:2000 | Information technology Telecommunications and information exchange between systems List of standard data link layer protocols that utilize high-level data link control (HDLC) classes of procedures, list of standard XID format identifiers, list of standard mode-setting information field format identifiers, and list of standard user-defined parameter set identification values |
ISO/IEC 646:1991 | Information technology ISO 7-bit coded character set for information interchange |
ISO/IEC 2382-9:1995 | Information technology Vocabulary Part 9: Data communication |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.