MIL-DTL-32372 Revision A:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fitting, Adapter, Hydraulic and Pneumatic, NPTF to ORFS Connectors, 1500 to 3000 PSI and -65°F to 250°F
English
28-09-2016
08-05-2021
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
Specifies fittings, adapter, hydraulic, and pneumatic national pipe thread fuel, (NPTF) dryseal pipe threads to o-ring face seal (ORFS) connectors, 1500 to 3000 psi, -65 degrees F to 250 degrees F temperature range, for use in hydraulic or pneumatic systems.
| DocumentType |
Standard
|
| Pages |
17
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| SupersededBy |
This specification covers fittings, adapter, hydraulic, and pneumatic national pipe thread fuel, (NPTF) dryseal pipe threads to O-ring face seal (ORFS) connectors, 1500 to 3000 psi, -65°F to +250°F temperature range, for use in hydraulic or pneumatic systems. National Pipe Thread connector ends are in accordance with ASME B1.20.3 connector ends; the ORFS end is in accordance with SAE J1453/3 connector ends.
| MIL-DTL-32372-4 Revision A:2017 | Fitting, Adapter, Straight, Hydraulic and Pneumatic, NPTF Male to ORFS Bulkhead |
| MIL-DTL-32372-12 Revision A:2017 | Fitting, Adapter, Tee, Hydraulic and Pneumatic, NPTF Male on Branch to ORFS Male Run to Run |
| MIL-DTL-32372-8 Revision A:2017 | Fitting, Adapter, 45 Degree, Hydraulic and Pneumatic, NPTF Male to ORFS Female Swivel |
| MIL-DTL-32372-9 Revision A:2017 | Fitting, Adapter, 90 Degree, Hydraulic and Pneumatic, NPTF Male to ORFS Female Swivel |
| MIL-DTL-32372-7 Revision A:2017 | Fitting, Adapter, Straight, Hydraulic and Pneumatic, NPTF Male to ORFS Female Swivel |
| MIL-DTL-32372-6 Revision A:2017 | Fitting, Adapter, 90 Degree Male, Hydraulic and Pneumatic, NPTF to ORFS Bulkhead |
| MIL-DTL-32372-2 Revision A:2017 | Fitting, Adapter, 45 DegreesElbow, Hydraulic and Pneumatic, NPTF Male to ORFS Male |
| MIL-DTL-32372-11 Revision A:2017 | Fitting, Adapter, Tee, Hydraulic and Pneumatic, ORFS Male to ORFS Female Swivel to NPTF Male on Branch |
| MIL-DTL-32372-5 Revision A:2017 | Fitting, Adapter, 45 Degree, Hydraulic and Pneumatic, NPTF Male to ORFS Bulkhead |
| MIL-DTL-32372-10 Revision A:2017 | Fitting, Adapter, Tee, Hydraulic and Pneumatic, ORFS Female Run to Run to NPTF Male on Branch |
| MIL-DTL-32372-1 Revision A:2017 | Fitting, Adapter, Straight, Hydraulic and Pneumatic, NPTF Male to ORFS Male |
| MIL-DTL-32372-3 Revision A:2017 | Fitting, Adapter, 90 Degree Elbow, Hydraulic and Pneumatic, NPTF Male to ORFS Male |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| SAE AMS5645S | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (321) Solution Heat Treated |
| SAE AMSQQA225/9A | Aluminum Alloy 7075, Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished |
| SAE AMSQQP416E | Plating, Cadmium (Electrodeposited) |
| SAE AMSP5510A | O-Ring, Preformed, Straight Thread Tube Fitting Boss, Type I Hydraulic (-65 to 160 °F) |
| MIL-DTL-16232 Revision G:2000 | Phosphate Coating, Heavy, Manganese or Zinc Base |
| MIL-PRF-7808 Revision L:1997 | Lubricating Oil, Aircraft Turbine Engine, Synthetic Base |
| ANSI/NCSL Z540 3 : 2006(R2013) | REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT |
| MIL-PRF-5606 Revision H:2002 | Hydraulic Fluid, Petroleum Base; Aircraft, Missile, and Ordnance |
| SAE AMS6382P | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) Annealed |
| SAE AMS5643U | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
| SAE AMS5743J | Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered |
| ASTM E 384 : 2017 : REDLINE | Standard Test Method for Microindentation Hardness of Materials |
| SAE AMSWWT700/4A | Tube, Aluminum Alloy, Drawn, Seamless, 5052 |
| SAE AMSA22771C | Aluminum Alloy Forgings, Heat Treated |
| SAE J403_201406 | Chemical Compositions of SAE Carbon Steels |
| SAE AMSWWT700/6C | Tube, Aluminum Alloy, Drawn, Seamless, 6061 |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AMS5647K | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 9.5Ni Solution Heat Treated |
| MIL-STD-889 Revision C:2016 | Galvanic Compatibility of Electrically Conductive Materials |
| MIL-DTL-81706 Revision B:2004 | Chemical Conversion Materials for Coating Aluminum and Aluminum Alloys |
| MIL-PRF-87257 Revision C:2017 | Hydraulic Fluid, Fire Resistant; Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile |
| SAE AMS2417J | Plating, Zinc-Nickel Alloy |
| SAE J1453/3_201206 | Specification for O-Ring Face Seal Connectors: Part 3 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Caps, and Connectors with SAE J1926-2 Inch Stud Ends |
| ASTM B 567 : 1998 | Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method |
| SAE J515_201511 | Specification for O-Ring Materials Used with Hydraulic Connectors |
| SAE J1453/1_201205 | Specification for O-Ring Face Seal Connectors: Part 1 - Tube Connection Details and Common Requirements for Performance and Tests |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid power connections |
| SAE J514_201201 | Hydraulic Tube Fittings |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| SAE AMS2700E | Passivation of Corrosion Resistant Steels |
| MIL-PRF-83282 Revision D:1997 | Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code Number H-537 |
| SAE AMS5639J | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 10Ni Solution Heat Treated |
| SAE AMS6370P | Steel, Bars, Forgings, and Rings 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) |
| FED-STD-162 Revision A:1967 | Hose, Rubber, Visual Inspection Guide for (Future Acquisitions May Refer to the Association for Hose and Accessories Distribution (NAHD) Handbook \"Design and Specification of Hose Assemblies\") |
| MIL-C-15726 Revision F:1988 | Copper-Nickel Alloy, Sheet, Plate, Strip, Bar, Rod and Wire |
| SAE AMS4124E | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73, T7351) Solution Heat Treated, Stress Relieved by Stretching, and Overaged |
| SAE AMS4928V | Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes 6Al - 4V Annealed |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.