MIL-L-8937 Revision D:1982
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING, [NATO CODE NUMBER S 1738]
Available format(s)
PDF
Superseded date
15-08-1988
Superseded by
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.Covers requirements for solid film lubricant intended to reduce wear and prevent galling, corrosion and seizure of metals.
| DevelopmentNote |
Supersedes DEFSTAN 91-19/1(1973) (10/2003)
|
| DocumentType |
Standard
|
| Pages |
17
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE AS85731B | Fastener, Positive Locking, Electronic Equipment, General Specification For |
| MIL-H-21367 Revision E:1985 | HULL FITTINGS: CONNECTORS, ADAPTER, END SEALS, AND STUFFING TUBES FOR FLEXIBLE, SOLID-DIELECTRIC, RADIO-FREQUENCY CABLES |
| MIL-F-85421 Revision B:1986 | FITTINGS, TUBE, FLUID SYSTEMS, SEPARABLE, BEAM SEAM, 3000/4000 PSI - GENERAL SPECIFICATION FOR |
| ASTM D 2625 : 1994 : R2003 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| MIL I 45932 : 0 | INSERT, SCREW THREAD, THIN WALL, LOCK IN |
| DEFSTAN 00-970(PT0)/9(2012) : 2012 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/14(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| MIL BULL 343 : A | DOCUMENTS APPLICABLE TO AIRCRAFT ENGINES AND PROPELLERS, USE OF |
| MIL I 45910 : C | INSERT, SCREW THREAD LOCKED IN & RING LOCKED 1 SERRATED GENERAL SPECIFICATION FOR |
| DEFSTAN 00-970(PT0)/11(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/13(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/12(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/8(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/10(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| MIL-STD-2156 Base Document:1983 | LAUNCHER, RAIL, GUIDED MISSILE, AIRCRAFT, GENERAL DESIGN CRITERIA FOR |
| MIL-STD-726 Revision H:1985 | PACKAGING REQUIREMENTS CODE |
| MIL-I-45934 Base Document:1971 | INSERT, SCREW THREAD, KEYRING LOCKED, SELF LOCKING AND NON SELF LOCKING, 125, 180, AND 220 KSI FTU: GENERAL SPECIFICATION FOR |
| SAE J2270_201606 | Ship Systems and Equipment - Threaded Fasteners - Inspection, Test, and Installation Guidance |
| ASTM D 2625 : 1994 : R2010 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| DOD-I-63274 Revision A:1983 | Insert, Screw Thread-Thin Wall, Locked in, Metric, General Specification for |
| ASTM D 2625 : 1994 : R1998 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| MIL-C-81582 Revision B:1975 | CONNECTOR, ELECTRICAL, BAYONET COUPLING, ENVIRONMENTAL RESISTING, UMBILICAL, GENERAL SPECIFICATION FOR |
| MIL-F-85731 Base Document:1986 | FASTENER, POSITIVE LOCKING, ELECTRONIC EQUIPMENT GENERAL SPECIFICATION FOR |
| ASTM D 2625 : 1994 : R2015 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| MIL-N-85729 Base Document:1988 | NUT, SELF-LOCKING, A-286, 160 KSI FTU, 450 DEGREES F, GENERAL SPECIFICATION FOR |
| MIL H 85800 : 0 | HOSE ASSEMBLIES, POLYTETRAFLUOROETHYLENE, ARAMID FIBER REINFORCED, 5000 & 8000 PSI, GENERAL SPECIFICATION FOR |
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| MIL-F-85720 Base Document:1985 | FITTING, TUBE, FLUID SYSTEMS, SEPARABLE, HIGH PRESSURE, DYNAMIC BEAM, SEAL, GENERAL SPECIFICATION FOR |
| NASM 21209 : 2003 | INSERT, SCREW THREAD, COARSE AND FINE, SCREW LOCKING, HELICAL COIL, CRES |
| MIL I 45916 : B | INSERT,SCREW THREAD - THREAD CUTTING AND THREAD FORMING |
| NAS1599:1980 | CONNECTORS, GENERAL PURPOSE, ELECTRICAL, MINIATURE CIRCULAR, ENVIRONMENT RESISTING, 200 DEG. C. MAXIMUM TEMPERATURE |
| MIL L 23699 : E | LUBRICATING OIL, AIRCRAFT TURBINE ENGINES, SYNTHETIC BASE |
| MIL-STD-290 Revision H:2013 | PACKAGING AND MARKING OF PETROLEUM AND RELATED PRODUCTS |
| MIL T 5624 : R | TURBINE FUEL, AVIATION, GRADES JP 4 AND JP 5 |
| ASTM D 1310 : 2014 : REDLINE | Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus |
| VV-D-1078 Revision B:1983 | DAMPING FLUID, SILICONE BASE (DIMETHYL POLYSILOXANE) |
| MIL H 83282 : C | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, AIRCRAFT, METRIC, NATO CODE NUMBER H 537 |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| MIL-A-8243 Revision D:1985 | ANTI-ICING AND DEICING-DEFROSTING FLUIDS |
| QQ-A-250-5 Revision F:1971 | ALUMINUM ALLOY ALCLAD 2024, PLATE AND SHEET |
| MIL L 2104 : F | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT TACTICAL SERVICE |
| FED-STD-791 Revision D:2007 | TESTING METHOD OF LUBRICANTS, LIQUID FUELS, AND RELATED PRODUCTS |
| DOD P 16232 : F | PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (FOR FERROUS METALS) |
| MIL C 372 : C | CLEANING COMPOUND, SOLVENT FOR BORE OF SMALL ARMS AND AUTOMATIC AIRCRAFT WEAPONS |
| MIL-STD-105 Revision E:1989 | SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES |
| MIL-T-81533 Revision A:1967 | TRICHLOROETHANE, 1, 1, 1, (METHYL CHLOROFORM) INHIBITED, VAPOR DEGREASING |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.