MIL-STD-242-12 Revision H:1984
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
ELECTRONIC EQUIPMENT PARTS SELECTED STANDARDS HARDWARE & INSULATORS PART 12 (NO S/S DOCUMENT)
Available format(s)
PDF
Published date
18-07-1984
Publisher
Withdrawn date
18-05-1996
€16.67
Excluding VAT
1. SCOPE
2. APPLICABLE DOCUMENTS
3. DEFINITIONS
4. GENERAL REQUIREMENTS
5. IDENTIFICATION
Describes the requirements for the selection of hardware and insulators used in the design and manufacture of Navy equipment.
| DevelopmentNote |
H NOTICE 1 - Notice of Change. H NOTICE 2 - Notice of Cancellation without replacement. (07/2005)
|
| DocumentType |
Standard
|
| Pages |
409
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Withdrawn
|
This standard establishes the requirements for the selection of hardware and in-sulators used in the design and manufacture of Navy equipment.
| MIL-F-22978 Revision A:1963 | Fastener, Rotary, Quick-Operating, High-Strength (ASG) (S/S by NASM22978) |
| MS14102 Revision J:1994 | BEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, WIDE, CHAMFERED OUTER RING, -65 DEG. F TO 325 DEG. F (S/S BY SAE-AS14102) |
| MIL-I-23264 Revision A:1968 | Insulators, Ceramic, Electrical and Electronic, General Specification for |
| MS51848 Revision E:1993 | WASHER, LOCK-HELICAL SPRING, HI-COLLAR |
| MS14101 Revision J:1994 | Bearings, Plain, Self-Locking, Self Lubricating, Low Speed, Narrow, Grooved Outer Ring, -65 Degrees to +325 Degrees F (S/S by SAE-AS14101) |
| MS35336 Revision D:1970 | Washer, Lock Countersunk, 80 Degrees, 82 Degrees, External Tooth (IN/MM) |
| MS21250 Revision L:1989 | BOLT, TENSION, STEEL, EXTERNAL WRENCHING, FLANGED, 12-POINT, 180 KSI FTU, 450 DEG F (S/S BY NASM21250) |
| MS21134 Base Document:1972 | BOLT, TENSION, STEEL, 180 KSI FTU, 450 DEGREE F, EXTERNAL WRENCHING, SPLINE DRIVE, FLANGED (S/S BY NASM21134) |
| MS27212 Revision P:1994 | TERMINAL BOARD ASSEMBLY, MOLDED-IN-STUD, ELECTRIC (S/S BY SAE-AS27212) |
| MS21098 Base Document:1994 | BOLT, SELF.LOCKING, STEEL, 160 KSI, FTU 250 DEG. F, 12 POINT, EXTERNAL WRENCHING (EXTERNALLY WRENCHING CAP SCREWS) (S/S BY NASM21098) |
| MIL-B-81935 Revision A:1987 | Bearings, Plain, Rod End, Self-Aligning, Self-Lubricating, General Specification for (S/S by SAE-AS81935) |
| MS21092 Revision A:1970 | Bolt, Self-Locking, 250 Deg. F, CRES, 48 KSI FSU, 80 KSI FTU, 100 Deg. Flush Head, Cross Recessed |
| MS15795 Revision G:1986 | Washer, Flat-Metal, Round, General Purpose (S/S by NASM15795) |
| MS24463 Revision H:1994 | BEARING, ROLLER, NEEDLE-SINGLE ROW, HEAVY DUTY, SELF-ALIGNING, TYPE III, ANTIFRICTION, INCH (S/S BY SAE-AS24463) |
| MS21438 Revision C:1997 | BEARING, ROLLER, NEEDLE, SINGLE ROW, HEAVY DUTY, TRACK ROLLER, SEALED, TYPE V, ANTIFRICTION, INCH (S/S BY SAE-AS21438) |
| MIL F 18240 : E | FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250 DEG F MAXIMUM |
| MS51960 Revision D:2011 | Screw, Machine-Flat Countersunk Head, 82 Degree, Cross-Recessed, Corrosion Resistant Steel, UNF-2A |
| MS20601 Revision J:1992 | RIVET, BLIND, STRUCTURAL PULL STEM, SELF-PLUGGING, 100 DEG. FLUSH HEAD, TYPE II (S/S BY NASM20601) |
| MS35335 Revision G:2004 | Washer, Lock, Flat-External Tooth |
| MS16995 Revision H:1997 | SCREW, CAP, SOCKET HEAD-HEXAGON, CORROSION RESISTANT STEEL, UNC-3A (S/S BY NASM16995) |
| MS21096 Revision C:1994 | BOLT, SELF-LOCKING, 75 KSI FSU, 125 KSI FTU PAN HEAD, CROSS RECESSED (S/S BY NASM21096) |
| MS14157 Revision B:1978 | BOLT, WHEEL, TENSION, FLANGED STEEL, 180KSI FTU, 450 DEG. F EXTERNAL SPLINE DRIVE (S/S BY NASM14157) |
| MS21099 Base Document:1965 | Bolt, Self Locking, Corrosion Resisting Steel, 80 KSI FTU, 250 Deg. F, 12-Point, External Wrenching (Externally Wrenching Cap Screws) |
| MS21095 Revision A:1971 | BOLT, SELF-LOCKING, 250 DEG. F, CRES, 48 KSI FSU, 80 KSI FTU, HEX HEAD (S/S BY NASM21095) |
| MS75004 Revision G:1987 | ADAPTER, BATTERY TERMINAL (STORAGE BATTERY) (NO S/S DOCUMENT) |
| MS25274 Revision G:1982 | CAP, ELECTRICAL (WIRE END, CRIMP STYLE, TYPE II, CLASS 1) FOR 105 DEG. C TOTAL CONDUCTOR TEMPERATURE (S/S/ BY SAE-AS25274) |
| MIL-STD-1277 Revision B:1983 | SPLICES, TERMINALS, TERMINAL BOARDS, BINDING POSTS, TERMINAL JUNCTION SYSTEMS, WIRE CAPS; ELECTRICAL (S/S BY MIL-HDBK-1277) |
| MS21004 Revision D:1981 | TERMINAL, LUG, UNINSULATED, RECTANGULAR TONGUE, CRIMP STYLE, COPPER, TYPE 1, CLASS 1 FOR 175 DEG. C TOTAL CONDUCTOR TEMPERATURE (S/S BY SAE-AS21004) |
| MIL-T-81714 Revision E:1988 | Terminal Junction System (TJS), Environment Resistant General Specification for (S/S by SAE-AS81714) |
| MS25036 Revision P:1986 | TERMINAL, LUG, CRIMP STYLE, COPPER, INSULATED, RING TONGUE, BELL MOUTHED, TYPE II, CLASS I (FOR 105 DEG. C TOTAL CONDUCTOR TEMPERATURE) (S/S BY SAE-AS25036) |
| MIL-T-55164 Revision C:1987 | Terminal Boards, Molded, Barrier, Screw and Stud Types, and Associated Accessories, General Specification for (S/S by A-A-59125) |
| MIL-B-81936 Base Document:1973 | Bearings, Plain, Self-Aligning (BECU Ball, CRES Race) General Specification for (S/S by SAE-AS81936) |
| MS51958 Revision C:1983 | Screw, Machine Pan-Head, Cross-Recessed, Corrosion Resisting Steel, UNF-2A (S/S by NASM51958) |
| MIL-P-55149 Revision B:1988 | POSTS, BINDING, ELECTRICAL (INSULATED AND UNINSULATED), GENERAL SPECIFICATION FOR (NO S/S DOCUMENT) |
| MIL-STD-1762 Base Document:1979 | BEARINGS AND BUSHINGS, PLAIN, PREFERRED FOR DESIGN, LISTING OF (NO S/S DOCUMENT) |
| MIL-F-8975 Revision B:1982 | Fasteners, Blind, High Strength, Installation Formed, Corrosion Resistant Steel, Heat Resistant Steel and Titanium, General Specification for (S/S by NASM8975) |
| MIL-B-81820 Revision F:1994 | Bearings, Plain, Self-Aligning, Self-Lubricating, Low Speed Oscillation, General Specification for (S/S by SAE-AS81820) |
| MS21097 Revision E:1992 | BOLT, SELF-LOCKING, 250 DEG. F, CRES, 48 KSI FSU, 80 KSI FTU, PAN HEAD, CROSS RECESSED (S.S BY NASM21097) |
| W-C-440 Revision B:1970 | CLIP, ELECTRICAL, GENERAL SPECIFICATION FOR (S/S BY A-A-59466) |
| MS27429 Revision F:1986 | SPLICE, CONDUCTOR, DISCONNECT, CRIMP STYLE, COPPER, INSULATED BARREL, TYPE II, CLASS 1 FOR 105 DEG. C TOTAL CONDUCTOR TEMPERAURE (S/S BY SAE-AS27429) |
| MS21140 Revision J:1998 | FASTENER, BLIND, HIGH STRENGTH, PULL TYPE, POSITIVE MECHANICAL LOCK, 100 DEG. FLUSH HEAD, CORROSION RESISTING STEEL, 95 KSI FSU (S/S BY NASM21140) |
| MS24679 Revision E:1990 | NUT, PLAIN, CAP, LOW CROWN, UNC-2B AND UNF-2B (S/S BY A-A-55629) |
| MIL-B-7838 Revision C:1989 | Bolt, Internal Wrenching, 160 KSI FTU (S/S by NASM7838) |
| MS17143 Revision F:1981 | TERMINAL, LUG, CRIMP STYLE, COPPER, INSULATED, RECTANGULAR TONGUE, TYPE II, CLASS 1 FOR 105 DEG. C. TOTAL CONDUCTOR TEMPERATURE (S/S BY SAE-AS17143) |
| MS35489 Revision K:2012 | Grommets, Synthetic and Silicone Rubber, Hot-Oil and Coolant Resistant |
| MS24464 Revision H:1994 | BEARING, ROLLER, NEEDLE-DOUBLE ROW, HEAVY DUTY, SELF-ALIGNING, TYPE IV, ANTIFRICTION, INCH (S/S BY SAE-AS24464) |
| MS35307 Revision E:1997 | SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT), STEEL, CORROSION RESISTING, PASSIVATED, UNC-2A (S/S BY NASM35307) |
| MS20600 Revision J:1992 | RIVET, BLIND, STRUCTURAL PULL STEM, SELF-PLUGGING, PROTRUDING HEAD, TYPE II (S/S BY NASM20600) |
| MIL-T-7928 Revision G:1976 | Terminals, Lug: Splices, Conductor: Crimp Style, Copper, General Specification for (S/S BY SAE-AS7928) |
| MS17731 Revision C:1971 | FASTENER, ROTARY, QUICK-OPERATING, FLUSH HEAD, FLOATING TYPE, 2210 LBS MIN TENSILE STRENGTH (S/S BY NASM17731) |
| MS 17732 : C | |
| MIL-B-81934 Revision B:1991 | Bearings, Sleeve, Plain and Flanged, Self-Lubricating, General Specification for (S/S by SAE-AS81934) |
| MS21432 Revision B:1994 | Bearing, Roller, Needle, Track Roller, Integral Stud, Type VII, Antifriction, Inch (S/S by SAE-AS21432) |
| MIL C 85052 : A | CLAMP LOOP, CUSHION, GENERAL SPECIFICATION FOR |
| MIL-T-55155 Revision C:1993 | TERMINALS, FEEDTHRU (INSULATED) AND TERMINALS, STUD (INSULATED AND NONINSULATED), GENERAL SPECIFICATION FOR (S/S BY A-A-59126) |
| MS21094 Base Document:1965 | BOLT, SELF-LOCKING, 250 DEG.F., STEEL, 75 KSI FSU, 125 KSI FTU, HEX HEAD (S/S BY NASM21094) |
| MS51957 Revision D:1997 | Screw, Machine, Pan Head, Cross-Recessed, Corrosion Resistant Steel, UNC-2A |
| MS20004THRUMS20024 Revision E:1989 | Bolts, Internal Wrenching, 160 KSI FTU and 96 KSI FSU (S/S by NASM20004THRU20024) |
| MIL-B-8831 Revision B:1982 | Bolt, 180 KSI FTU and 180 KSI FSU, 450 Degrees F Protruding and Flush Head, General Specification for (S/S by NASM8831) |
| MIL-B-3990 Revision D:1980 | Bearings, Roller, Needle, Airframe, Antifriction, Inch (S/S by SAE-AS39901) |
| MS14103 Revision J:1994 | BEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, WIDE, GROOVED OUTER RING, -65 DEG. TO 325 DEG. F (S/S BY SAE-AS14103) |
| MS16996 Revision F:1993 | SCREW, CAP, SOCKET HEAD-HEXAGON, CORROSION RESISTANT STEEL, UNF-3A (S/S BY NASM16996) |
| MIL-R-7885 Revision D:1988 | Rivets, Blind, Structural, Mechanically LockedSpindleand Friction Locked Spindle, General Specification for |
| MS35691 Revision E:2005 | Nut, Plain, Hexagon (JAM) UNC-2B and UNF-2B |
| MS51959 Revision D:1997 | SCREW, MACHINE-FLAT COUNTERSUNK HEAD, 82 DEG., CROSS-RECESSED, CORROSION - RESISTANT STEEL, UNC-2A (S/S BY NASM51959) |
| MS14104 Revision J:1994 | BEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, NARROW, CHAMFERED OUTER RING, -65 DEG. F TO 325 DEG. F (S/S BY SAE-AS14104) |
| MS35338 Revision L:1994 | WASHER, LOCK-SPRING, HELICAL, REGULAR (MEDIUM) SERIES (S/S BY NASM35338) |
| MS20604 Revision K:1995 | RIVET, BLIND, NONSTRUCTURAL, UNIVERSAL HEAD, CLASS 1 (S/S BY NASM20604) |
| MS21091 Base Document:1965 | Bolt, Self-Locking, 250 Deg. F., Steel, 75 KSI FSU, 125 KSI FTU, 100 Deg. Flash Head Cross Recessed |
| MIL N 25027 : G | NUT, SELF-LOCKING, 250 DEGREES F, 450 DEGREES F, AND 800 DEGREES F |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.