MIL-STD-31000 Revision A:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Technical Data Packages
15-05-2021
26-02-2013
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
APPENDIX A - SELECTION AND ORDERING GUIDANCE
APPENDIX B - MODEL BASED DEFINITION (MBD) - MODEL
ORGANIZATIONAL SCHEMA
APPENDIX C - 3D TDP VALIDATION GUIDE
Specifies requirements for the deliverable data products associated with a technical data package (TDP) and its related TDP data management products. A TDP contains elements, is described by a level and type, and may have associated metadata and supplementary technical data.
DevelopmentNote |
Supersedes MIL DTL 31000 (C). (12/2009) Supersedes MIL T 47500. (11/2010) A NOTICE 1 - Notice of Validation. (12/2017)
|
DocumentType |
Standard
|
Pages |
167
|
PublisherName |
US Military Specs/Standards/Handbooks
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
This standard defines the requirements for a technical data package (TDP) and its related TDP data management products. The purpose of the TDP is to provide an authoritative technical description of an item which is clear, complete and accurate, and in a form and format adequate for its intended use. A TDP contains elements, is described by a level and type, and may have associated metadata and supplementary technical data. A TDP is a sub-set of product and technical data as shown in the hierarchical breakdown in Figure 1.
MIL-DTL-83425 Revision A:2006 | EARCUP, SOUND PROTECTIVE MX-8376/AR |
MIL-C-70628 Base Document:1987 | Container, Ammunition, PA108 Assembly |
GEIA HB 649 : 2005 | CONFIGURATION MANAGEMENT STANDARD IMPLEMENTATION GUIDE |
MIL-STD-3001-1 Revision A:2014 | PREPARATION OF DIGITAL TECHNICAL INFORMATION FOR MULTI-OUTPUT PRESENTATION OF TECHNICAL MANUALS (PART 1 OF 8 PARTS) |
MIL DTL 18396 : E | SWITCHES, METER AND CONTROL, NAVAL SHIPBOARD |
DEFSTAN 00-970(PT0)/9(2012) : 2012 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/17(2016) : 2016 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/14(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
MIL-DTL-25531 Revision F:2013 | Coupling Half, Quick Disconnect, Pneumatic Starter, External, Low Pressure |
DEFSTAN 00-970(PT0)/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
MIL-DTL-7788 Revision H:2011 | PANELS, INFORMATION, INTEGRALLY ILLUMINATED |
DEFSTAN 00-970(PT0)/13(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/12(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/15(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/11(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
MIL-DTL-5099 Revision C:2011 | INDICATOR, CABIN AIR PRESSURE, 1-7/8 INCH DIAL, TYPE MA-1 |
DEFSTAN 00-970(PT0)/8(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
MIL-DTL-27723 Revision F:2013 | Probe, Total Temperature, Deiceable |
DEFSTAN 00-970(PT0)/10(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/16(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DSCC 85078 : E | DELAY LINES, ACTIVE, PROGRAMMABLE 3 BIT, 16 PIN DIP COMPATIBLE, EMITTER-COUPLED LOGIC (ECL) |
DSCC 90046 : E | GASKETS, SHIELDING, EMI/RFI, ORIENTED WIRES IN SILICONE RUBBER |
IEEE 15288.2-2014 | IEEE Standard for Technical Reviews and Audits on Defense Programs |
SAE ARP 5812 : 2017 | ACTUATORS, LINEAR MECHANICAL, GENERAL SPECIFICATION GUIDE |
MIL-PRF-24755 Revision B:2010 | Fans, Vaneaxial, High Pressure, Naval Shipboard |
SAE AS 21608 : 2012 | FERRULE, SHIELD TERMINATING, CRIMP STYLE |
MIL-DTL-5421 Revision D:2011 | TUBES, PITOT, ELECTRICALLY HEATED, AIRCRAFT |
MIL-HDBK-115 Revision C:2016 | U.S. ARMY REVERSE ENGINEERING HANDBOOK (GUIDELINES AND PROCEDURES) |
MIL-DTL-7601 Revision C:2011 | GAGE, EMERGENCY OXYGEN, TYPE L-2 |
EIA CMB7-4 : 2011 | GLOSSARY OF TERMS, ACRONYMS, AND DEFINITIONS |
SAE EIA 649/1 : 2014 | CONFIGURATION MANAGEMENT REQUIREMENTS FOR DEFENSE CONTRACTS |
MIL-HDBK-502 Revision A:2013 | Product Support Analysis |
MIL-DTL-27166 Revision F:2013 | VALVE, PRESSURE EQUALIZING, GASEOUS PRODUCTS |
MIL-STD-3046 Base Document:2013 | CONFIGURATION MANAGEMENT |
MIL-DTL-2212 Revision K:2014 | CONTACTORS AND CONTROLLERS, ELECTRIC MOTOR AC OR DC, AND ASSOCIATED SWITCHING DEVICES |
SAE J 1776 : 2014 | MARINE VEHICLES - HYDRAULIC SYSTEM PUMPS AND MOTORS - DESIGN AND SPECIFICATION GUIDE |
GEIASTD0007B:2013 | LOGISTICS PRODUCT DATA |
MIL-DTL-27715 Revision C:2014 | Circuit Breaker, Trip-Free, High Temperature, Aircraft General Specification for |
MIL-DTL-901 Revision E:2017 | Shock Tests, H.I. (High-Impact) Shipboard Machinery, Equipment, and Systems, Requirements for |
MIL-DTL-9320 Revision E:2010 | Signal, Warning, Audible, for Headset, Type MA-1 |
MIL-DTL-25446 Revision E:2012 | Transmitter, Temperature, Electrical Resistance, Armored, Bayonet Locking Type, (-50 Degrees C to 300 Degrees C) |
MIL-DTL-5794 Revision C:2006 | MICROPHONE UNIT M-6A/UR AND MICROPHONE, CARBON M-51/UR (CARBON NOISE CANCELING) |
SAE AS 4073 : 2013(R2018) | AIR CYCLE AIR CONDITIONING SYSTEMS FOR MILITARY AIR VEHICLES |
MIL-DTL-5904 Revision E:2010 | LIGHT, RUNWAY MARKER, ELEVATED, TYPE C-1 |
MIL-PRF-19004 Revision B:2001 | FANS, CENTRIFUGAL, VENTILATION, NAVAL SHIPBOARD |
MIL-DTL-32385 Base Document:2011 | CONNECTOR, RECEPTACLES, PLUGS, ADAPTER, USED ON ELECTROLUMINESCENT, EMBEDDED, AND PRINTED CIRCUIT BOARD LAMP LIGHTING PANELS |
MIL-DTL-6019 Revision E:2011 | GAGES, PRESSURE, DIAL INDICATING, LOW-PRESSURE OXYGEN |
DSCC 92017 : A | GASKETS, EMI/RFI SHIELDING, EXPANDED PTFE WITH CARBON FILLER |
MIL-DTL-6839 Revision E:2011 | INDICATOR, POSITION, LANDING GEAR |
MIL-DTL-27193 Revision D:2017 | INDICATOR, ATTITUDE ARU-2B/A |
SAE ARP 5794 : 2014 | CENTRIFUGAL AIRCRAFT FUEL PUMP REQUIREMENTS, DESIGN AND TESTING, AEROSPACE STANDARD |
SAE ARP 4058 : 2017 | GENERAL SPECIFICATION GUIDE FOR MECHANICAL GEARED ROTARY ACTUATORS |
SAE EIA 649/2 : 2016 | CONFIGURATION MANAGEMENT REQUIREMENTS FOR NASA ENTERPRISES |
ASME Y14.100 : 2017 | ENGINEERING DRAWING PRACTICES - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
VDA 4955 : 2006 | |
ASME Y14.5 : 2009 | DIMENSIONING AND TOLERANCING |
MIL-STD-2073-1 Revision E:2008 | STANDARD PRACTICE FOR MILITARY PACKAGING |
ISO/PAS 26183:2006 | SASIG Product data quality guidelines for the global automotive industry |
ASME Y14.24 : 2012 | TYPES AND APPLICATIONS OF ENGINEERING DRAWINGS - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
ASME Y14.34 : 2013(R2018) | ASSOCIATED LISTS - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
DOD 4100.39-M : 2010 | FEDERAL LOGISTICS INFORMATION SYSTEM - VOLUME 10: PROCEDURES MANUAL MULTIPLE APPLICATION REFERENCES/INSTRUCTIONS/TABLES AND GRIDS |
ISO/IEC 12207:2008 | Systems and software engineering Software life cycle processes |
ISO 32000-1:2008 | Document management — Portable document format — Part 1: PDF 1.7 |
FED-STD-376 Revision B:1993 | PREFERRED METRIC UNITS FOR GENERAL USE BY THE FEDERAL GOVERNMENT |
VDA 4958-3 : 2006 | LONG TERM ARCHIVING (LTA) OF DIGITAL PRODUCT DATA WHICH ARE NOT BASED ON TECHNICAL DRAWINGS - PART 3: DATA MODEL |
MIL-STD-963 Revision B:1997 | DATA ITEM DESCRIPTIONS (DIDS) |
MIL-STD-967 Base Document:2003 | DEFENSE HANDBOOKS FORMAT AND CONTENT |
ASME Y14.41 : 2012 | DIGITAL PRODUCT DEFINITION DATA PRACTICES - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
DOD-STD-2101 Base Document:1979 | CLASSIFICATION OF CHARACTERISTICS |
ASME Y14.1 : 2012 | DECIMAL INCH DRAWING SHEET SIZE AND FORMAT - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
ASME Y14.100 : 2017 | ENGINEERING DRAWING PRACTICES - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
NAS 3500 : REV 1 | TECHNICAL DATA PACKAGE: COMPOSITION, COMMUNICATION, AND APPLICATION |
DOD 5220.22M : 95 SUP1 CHANGE 1 | INDUSTRIAL SECURITY MANUAL FOR SAFEGUARDING CLASSIFIED INFORMATION |
MIL-STD-961 Revision E:2003 | DEFENSE AND PROGRAM-UNIQUE SPECIFICATIONS FORMAT AND CONTENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.