MIL-STD-35-72 Base Document:1974

FOREWORD
1.0 Actuators, Electromechanical, Rotary
1.1 Specification Title Index
1.2 Specification Requirements Instructions
    1.2.1 General
    1.2.2 Effectivity of Data
    1.2.3 Writing Methodology
    1.2.4 Characteristic Codes and Characteristic Value
           Codes
    1.2.5 Actuator Characteristics
    1.2.6 Dimensions and Drawings
    1.2.7 Materials and Finishes
    1.2.8 Additional Requirements, Marking, Packaging,
           Quality Assurance, and Notes
    1.2.9 Applicable Documents
    1.2.10 Quality Assurance and Conformance
    1.2.11 Detailed Requirements
    1.2.12 Date
    1.2.13 FSCM/Code Ident of Requester
    1.2.14 Prime Contract Number
    1.2.15 Applicable General Specification
    1.2.16 Generated Document
    1.2.17 Item Application
    1.2.18 Drawing Figure Number
    1.2.19 Dimensions
    1.2.20 Design Characteristics
    1.2.21 Actuator Materials
    1.2.22 Actuator Finishes
    1.2.23 Travel
    1.2.24 Operating Torque
    1.2.25 Stall Torque
    1.2.26 Holding Torque
    1.2.27 Rated Load
    1.2.28 Maximum Operating Load
    1.2.29 Stall Load
    1.2.30 Output Shaft Revolutions
    1.2.31 Backlash
    1.2.32 Coast
    1.2.33 Repeatabi1ity
    1.2.34 Travel Limit Stops
    1.2.35 Brakes
    1.2.36 Operating Speed Adjustments
    1.2.37 Reversibility
    1.2.38 Position Transmitters
    1.2.39 Thermal Protection
    1.2.40 Duty Cycle
    1.2.41 Over-Riding Loads
    1.2.42 Rated Life
    1.2.43 Clutch
    1.2.44 Motor-to-Output Shaft Gear Ratio
    1.2.45 Output Shaft Side Loading
    1.2.46 Motor
    1.2.47 Efficiency
    1.2.48 Power Consumption
    1.2.49 Input Power
    1.2.50 Electrical Connectors
    1.2.51 Electrical Wiring
    1.2.52 Electrical Connections
    1.2.53 Weight
    1.2.54 Locking of Parts
    1.2.55 Housing
    1.2.56 Output Shaft
    1.2.57 Lubrication
    1.2.58 Retaining Rings
    1.2.59 Spring Pins
    1.2.60 Operating Temperature
    1.2.61 Storage Temperature
    1.2.62 Operating Altitude Range
    1.2.63 Nameplate and Product Marking
    1.2.64 Wiring Diagram Nameplate
    1.2.65 Motor Data Nameplate
    1.2.66 Lubrication Data Nameplate
    1.2.67 Interference (Conducted)
    1.2.68 Interference (Radiated)
    1.2.69 Electrical and Environmental Test Methods and
           Requirements
    1.2.70 Workmanship
    1.2.71 Sources
    1.2.72 Material and Process Substitution
    1.2.73 Supersession Data
    1.2.74 Test Data and Test Methods
    1.2.75 Specification Requirements, Appendices and SRS
    1.2.76 Specification Requirements Sheet (SRS) Form
    1.2.77 Searching for Existing Documents
Specification Requirements
Quality Assurance Requirements
Special Requirements
Table I. Actuators Materials Table
Table II. Actuator Finishes Table
Appendices
1.3 Configuration and Drawings
    1.3.1 Figure Titles vs Figure Numbers
    1.3.2 Legend Index
Figures 250-01-1 thru 250-02-1
Reproducible Foldout Specification Requirement Sheet (SRS) Forms
Reproducible Foldout Specification Requirement Sheet Tabulation Table

Describes the procedures to be followed, and the format to be used, for submission of requirements to obtain a computer generated procurement document.