MIL-T-81714 Revision E:1988
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Terminal Junction System (TJS), Environment Resistant General Specification for (S/S by SAE-AS81714)
02-03-1988
10-07-2006
Describes the Terminal Junction System parts used for interconnection of wiring and incorporation of passive components.
| DevelopmentNote |
Supersedes NAS 1818, NAS 1819, NAS 1820, NAS 1821, NAS 1822, NAS 1823, NAS 1824, NAS 1825, NAS 1826, NAS 1827, NAS 1828 & NAS 1817. (04/2005) Supersedes NAS 1748. (03/2006) E NOTICE 1 - Notice of Cancellation/Superseded by SAE AS 81714. (07/2006)
|
| DocumentType |
Standard
|
| Pages |
59
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| SupersededBy |
This specification covers Terminal Junction System (TJS) components which are used for interconnection of wiring and incorporation of passive components (see 6.1). These environment resistant components have in common the use of crimp type external pin contacts in accordance with MIL-C-39029/1 for Series 1 or crimp type external socket contacts in accordance with MIL-C-39029/22 for Series II. This family of TJS components is designed to operate continuously over a temperature range of -65 degrees C to 200 degrees C, using any combination of temperatures generated by the electrical load and ambient temperature so that the maximum internal hot spot, combined temperature, will not exceed the maximum specified for the class of TJS component, unless otherwise specified (1.2, 3.1).
| MIL-W-5088 Revision L:1991 | Wiring, Aerospace Vehicle (Future Design Should Refer to SAE-AS50881) |
| MIL-HDBK-508 Base Document:1998 | Wiring and Wiring Devices for Combat and Tactical Vehicles, Selection and Installation of |
| MIL-STD-339 Base Document:1987 | WIRING & WIRING DEVICES FOR COMBAT & TACTICAL VEHICLES, SELECTION 8 INSTALLATION (S/S BY MIL-HDBK-508) |
| MIL-STD-242-12 Revision H:1984 | ELECTRONIC EQUIPMENT PARTS SELECTED STANDARDS HARDWARE & INSULATORS PART 12 (NO S/S DOCUMENT) |
| MIL E 17807 : C | ELEVATOR, WEAPON AND CARGO, ELECTROMECHANICAL (SHIPBOARD) |
| MIL-STD-1277 Revision B:1983 | SPLICES, TERMINALS, TERMINAL BOARDS, BINDING POSTS, TERMINAL JUNCTION SYSTEMS, WIRE CAPS; ELECTRICAL (S/S BY MIL-HDBK-1277) |
| MIL-HDBK-1277 Base Document:1998 | Splices, Chips, Terminals, Terminal Boards, Binding Posts, Electrical |
| MIL-STD-1549 Revision A:1988 | COMMON TERMINATION SYSTEM FOR ELECTRICAL AND ELECTRONIC PARTS (NO S/S DOCUMENT) |
| MIL-C-39029-22 Revision B:1989 | Contacts, Electrical Connector, Socket, Crimp Removable, (For MIL-T-81714 Terminal Junction System Series II and MIL-C-81511 Series 3 and 4 Class L Connectors) (S/S by SAE-AS39029/22) |
| MIL-W-22759 Revision E:1990 | WIRE, ELECTRICAL, FLUOROPOLYMER-INSULATED, COPPER OR COPPER ALLOY (S/S BY SAE-AS22759) |
| MIL L 7808 : K (1) | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| MIL C 22520 : F | CRIMPING TOOLS, TERMINAL HAND OR POWER ACTUATED, WIRE TERMINATION AND TOOL KITS - GENERAL SPECIFICATION FOR |
| MIL-W-81044 Revision B:1973 | Wire, Electrical, Crosslinked Polyalkene, Crosslinked Alkane-Imide Polymer, or Polyarlyene Insulated, Copper or Copper Alloy (S/S by SAE-AS81044) |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| MIL L 23699 : E | LUBRICATING OIL, AIRCRAFT TURBINE ENGINES, SYNTHETIC BASE |
| SAE AIR1351H | Manufacturers\' Identification of Aerospace Electrical and Electronic Wiring Devices and Accessories |
| MIL-I-81969-8 Revision B:1986 | Installing and Removal Tools, Connector Electrical Contact, Types I and II, Class 2, Composition A (S/S by SAE-AS81969/8) |
| MIL C 55330 : B | CONNECTORS, PREPARATION FOR DELIVERY OF |
| MIL T 5624 : R | TURBINE FUEL, AVIATION, GRADES JP 4 AND JP 5 |
| MIL-STD-45662 Revision A:1988 | Calibration Systems Requirements (Refer to ISO-10012-1 and ANSI-Z540-1 or Comparable Standards as Alternatives to MIL-STD-45662) |
| MIL-STD-1277 Revision B:1983 | SPLICES, TERMINALS, TERMINAL BOARDS, BINDING POSTS, TERMINAL JUNCTION SYSTEMS, WIRE CAPS; ELECTRICAL (S/S BY MIL-HDBK-1277) |
| MIL-I-81969-14 Revision C:1987 | Installing and Removal Tools, Connector Electrical Contact, Type III, Class 2, Composition B (S/S By SAE-AS81969/14) |
| MIL-STD-889 Revision C:2016 | Galvanic Compatibility of Electrically Conductive Materials |
| MIL-I-81969-16 Revision A:1979 | Installing and Removal Tools, Connector Electrical Contact, Type III, Class 1, Composition B (S/S By SAE-AS81969/16) |
| MIL-I-17214 Revision B:1984 | Indicator, Permeability; Low-Mu (Go-No Go) (S/S by ASTM-A342) |
| MIL G 45204 : C | GOLD PLATING, ELECTRODEPOSITED |
| MIL-C-39029 Revision D:1988 | Contacts, Electrical Connector, General Specification for (S/S by SAE-AS39029) |
| MIL-STD-1344 Revision A:1977 | Test Methods for Electrical Connectors (S/S by EIA364, See Notice 6 for Individual Test Method Replacement) |
| MIL-A-8243 Revision D:1985 | Anti-Icing and Deicing-Defrosting Fluids (S/S by SAE-AMS1424) |
| MIL H 5606 : G | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE |
| MIL-STD-202 Revision H:2015 | Electronic and Electrical Component Parts |
| MIL-STD-1285 Revision D:2004 | Marking of Electrical and Electronic Parts |
| MIL-W-5088 Revision L:1991 | Wiring, Aerospace Vehicle (Future Design Should Refer to SAE-AS50881) |
| MIL-STD-105 Revision E:1989 | Sampling Procedures and Tables for Inspection by Attributes (See Notice 3 for Replacement Information) |
| MIL-C-39029-1 Revision F:1982 | Contacts, Electrical Connector, Pin, Crimp Removable, (For MIL-T-81714 Terminal Junction Systems) (S/S by SAE-AS39029/1) |
| MIL W 16878 : F | WIRE, ELECTRICAL, INSULATED, GENERAL SPECIFICATION FOR |
| MS27488 Revision N:2008 | Plug, End Seal, Electrical Connector |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.